brennenstuhl HTCZ01 Zigbee Radiator Thermostat Instruction Manual

May 15, 2024
brennenstuhl

Zigbee Radiator thermostat
Installation and operating instructions
HT CZ 01

Radiator thermostat HT CZ 01

SAFETY INSTRUCTIONS

WARNING: RISK OF DEATH AND ACCIDENTS FOR INFANTS AND CHILDREN! Never leave children unattended with the packaging material. There is the danger of suffocation through ingestion or inhalation of small parts or films. Children often tend to underestimate the dangers. Keep the device away from children. It is not a toy. This device can be used by children from 8 years as well as persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided that they have been given supervision or instruction conceming the safe use of the device and that they understand the resulting risks. Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision. Operate the device in a dry and dust-free environment only. Operate the device in an indoor environment only. Do not expose the device to unfavourable influences such as

  • Humidity,
  • Constant sunlight,
  • Heat radiation,
  • Cold,
  • Vibrations.

CAUTION RISK OF INURY!
We will not assume any liability for material or personal damage caused by improper handling or non-observance of the safety instructions! In such cases, the warranty / guarantee will become null and void!
Any other use than those described in these instructions will lead to damage of the device.
Do not undertake structural modifications to the device. Otherwise, safe operation cannot be assured.

INTENDED USE
Using the radio radiator thermostat, you can regulate the room temperature in a time- controlled manner and define heating phases according to your individual requirements, The room temperature is controlled by the radiator valve via the brennenstuhi*Connect fadiator thermostat.

INSTALLATION INFORMATION / DISTANCE TO SOURCES OF INTERFERENCE

This device works with the 2.4 GHz Zigbee protocol. The reach within buildings may strongly differ from the one in open areas.
Apart from the transmission power and the reception properties of the receivers, environmental influences such as air humidity and the structural situation on site play an important role.
The reach may be considerably reduced by:

  • Walls made of wood, plasterboard, concrete, reinforced concrete
  • Proximity to metal and conductive objects
  • Broadband interference, e.g. in residential areas (DECT phones, mobile phones, radio headphones, radio speakers, radio weather stations, baby monitoring systems)
  • Proximity to electric motors, transformers, power supply units, computers

SCOPE OF DELIVERY
1 x radiator thermostat
1 x operating instructions
2 x batteries LR6 / AA, mignon 1.5 V included
1 x adapter Danfoss RA, Danfoss RAV, Danfoss RAVL

TECHNICAL DATA

Designation of the product: HT CZ 01
Item no.: 1294070
Operating voltage: DC 3 V (2x AA alkaline)
Radio frequency: 2.4 GHz Zigbee
Frequency band: 2,400-2,483 GHz
Ambient temperature: 0 — 40 °C
Temperature range: Automatic mode: 5-30 °C

Manual mode: 5-30 °C
Frost protection mode: 5-15 °C
Union nut:| M30 x 1.5 mm
Measuring intervals:| every 2 minutes
Battery service life:| approx. 1 year

DEVICE OVERVIEW

  1. LCD

  2. Setting wheel
    Press: Change mode
    Rotate: Temperature adjustment

  3. LED

  4. Union nut

  5. Error

  6. Battery low

  7. Set temperature

  8. Window open

  9. Mode: Automatic

  10. Mode: Manual

  11. Installation mode

  12. Wireless network

  13. Child protection

DOWNLOADING THE APP / BRENNENSTUHL®CONNECT
The radiator thermostat is controlled using the brennenstuhl® Connect app. The app is available free of charge at the App Store and the Google Play Store. For the download and the installation, follow the instructions on the screen.
Google, GooglePlay and Google Home are trademarks of Google LLC.
Apple and the Apple logo are brands of Apple Inc. App Store is a service mark of Apple Inc.
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its partners.
COMPATIBLE WITH AMAZON ALEXA AND GOOGLE ASSISTANT
The device is compatible with Amazon Alexa and Google Assistant. For Amazon Alexa, download the brennenstuhl®Connect Skill and search for the radiator thermostat. For Google Assistant, select the Google Home App and click “Add”

“Set-up device”. Then follow the screen menu.

COMMISSIONING

Battery insertion:
The device is supplied with the batteries already inserted; please remove the contact protection.

  1. Rotate the external cover in the direction of the arrow (1) and then pull the cover in the direction of the arrow (2)

  2. Insert 2 mignon AA alkali batteries into the radiator thermostat.
    Ensure correct polarity. Please do not use rechargeable batteries.

  3. After insertion of the batteries, the current temperature and the symbol for the installation mode are displayed

  4. Push the cover onto the housing again in the direction of the arrow (1); afterwards, rotate the cover in the direction of the arrow (2) to lock it.

ASSEMBLY AT THE RADIATOR

The radiator thermostat can be assembled without draining heating water as it is not necessary to make any changes in the heating system itself. For the assembly, you only need a slotted or Philips screwdriver.
The radiator thermostat is equipped with a universal union nut (4) (M30x1.5 mm) and is thus suitable for the following valves without adapter:

• Heimeier
• MNG
• Junkers
• Honywell-Braukmann
• Landis/&Gyr (Duodyr)| • Oventrop
• Schlösser
• Comap
• Valf Sanayii| • Mertik Maxitrol
• Watts
• Wingenroth (Wiroex)
• R.B.M| • Tiemme
• Jaga
• Siemens
• Idmar
---|---|---|---

For Danfoss valves, you need the following adapter

Make View Adapter

Heimeier, Junkers, MNG, Honywell-
Braukmann, … etc. (see complete list
under “Assembly at the radiator“)| | Not required
Danfoss RA| | See enclosed adapters
Danfoss RAV| | See enclosed adapters
Danfoss RAVL| |

DISASSEMBLY OF THE ORIGINAL HEATING CONTROLLER

There are many different types of heating valves and thus also many different fastening systems. If possible, use the original instructions of the radiator thermostat for disassembly. First of all, set the original heating controller to the maximum value (A) by rotating it counterclockwise.
The valve is completely opened and the controller no longer pushes on the valve pin. Different disassembly options:
Union nut
Screw off the union nut by rotating it counterclockwise (B). Afterwards, you can remove the thermostat head.
Snap fastening
You can easily loosen thermostat heads fastened in this way be rotating the lock/union nut a little bit counterclockwise (C).
Afterwards, you can remove the thermostat head The system is only suitable for controlling radiators. Any other use e.g. at cooling systems or underfloor heatings etc. is not admissible.
INFORMATION ON THE USE OF THE RADIATOR THERMOSTAT WITH THE BRENNENSTUHL°CONNECT APP
To be able to enjoy the full functionality of the radiator thermostat, you need the brennenstuhl® Zigbee gateway GWY CZ 01 art. no. 1294060 to use the brennenstuhlConnect app and for connection into the network.
The gateway is the connection between the WiFi network and the brennenstuhl
Connect Zigbee radio products. To be able to use battery-operated products for a longer period of time, it is necessary to use the Zigbee radio technology.

INSTALLATION

  1. Keep the setting wheel pressed for 3 seconds before mounting the radiator thermostat on the heating valve.

  2. Shortly before F1 and the installation symbol flash, the radiator thermostat vibrates gently.
    Please turn to continue reading →

  3. Now screw the radiator thermostat on the valve by means of the union nut (for Danfoss valves, use the enclosed adapter). Slightly push the union nut forwards and rotate it clockwise onto the valve thread. The maximum torque of 5 Nm must not be exceeded.

  4. Keep the setting wheel pressed again until F12 appears.

  5. After ca. 10 seconds, the installation symbol goes out and the current temperature is displayed. The installation is completed.

INSTALLATION / ADJUSTMENT DRIVE

  1. After the installation, the radiator thermostat is automatically adjusted to the radiator valve. For this purpose, the radiator thermostat opens and closes the valve to determine the opened position and the closed position of the heating valve.
  2. If the process ends with an error, check whether the union nut is still screwed tight or whether the adapter has loosened. Afterwards, remove the batteries for 10 seconds.
    Then, re-insert the batteries into the radiator thermostat and activate the installation mode to start the automatic adjustment.
    To ensure proper functioning of the radiator thermostat, the influence of the thermal radiation of the radiator should be kept to a minimum. Please install the radiator thermostat as shown in the figure below.brennenstuhl HTCZ01
Zigbee Radiator Thermostat - ASSEMBLY ATTHE RADIATOR 9

SET-UP OF THE ZIGBEE GATEWAY ART. NO. 1294060

The gateway GWY CZ 01 art. no. 1294060 has an integrated 2.4 GHz WLAN module to allow for connection of the gateway with the router. Please deactivate the 5 GHz network of your router during the set-up of the gateway. The 5 GHz network can be re-activated once the set-up is completed.

  • Download the brennenstuhl®Connect app and install it.
  • Open the app and click the “+” symbol in the top right corner and select gateway 1294060.
  • Then add the gateway into the app by following the instructions given in the app.

SET-UP OF THE RADIATOR THERMOSTAT IN THE ZIGBEE GATEWAY
For teaching-in of the radiator thermostat, shortly press the setting wheel 3 times; the LED starts to flash. The teach-in mode is now active for 2 minutes and cannot be interrupted. After 2 minutes, the teach-in mode is automatically switched off.

  • Now open the brennenstuhl®Connect app and select the Zigbee gateway
  • Select “Add Zigbee device” at the lower end of the display
  • In the next step, select “LED is already flashing”
  • Now, the app searches for the radiator thermostat
  • After successful search, the device is displayed; select “Complete”
  • You can then change the device name and assign it to a room
  • Complete the set-up by means of “Complete”

OPERATION

  1. Mode: Automaticbrennenstuhl HTCZ01 Zigbee Radiator Thermostat - OPERATION The radiator thermostat automatically sets the desired temperature which has been defined in the brennenstuhl® Connect app before. For automatic mode, the radiator thermostahas to be connected to the brennenstuhl® Zigbee gateway art. no. 1294060 and the radio network must be active.
  2. Mode: Manualbrennenstuhl HTCZ01 Zigbee Radiator Thermostat - OPERATION 2 In the manual mode, the temperature can be fixedly set manually using the setting wheel. The temperature can be set between 5 and 30 °C.
  3. Mode: Frost protectionbrennenstuhl HTCZ01 Zigbee Radiator Thermostat - OPERATION 4 The frost protection mode is intended for keeping rooms free from frost so that, for example, water lines cannot freeze in at low temperatures. In frost protection mode, the temperature can be set between 5 and 15 °C.

ACTIVATING THE CHILD PROTECTION DIRECTLY AT THE RADIATORTHERMOSTAT

To activate/deactivate the child protection, you keep the setting wheel pressed for 3 seconds. If the child protection is active, no operation is possible any more at the radiator thermostat. The child protection is intended to prevent children from changing the radiator thermostat setting or other kinds of accidental tampering with the radiator thermostat.
If the child protection is active, a padlock symbol is shown in the display. OPEN WINDOW DETECTION (can only be set in the brennenstuhl®Connect app)
The Open window function can be activated or deactivated in the brennenstuhl®Connect app. If the function is activated, the radiator thermostat detects an open window and closes the valve for 30 min. In this way, the heat loss can be reduced. The Open window function is activated by default. To deactivate/activate the Open window function, open the brennenstuhl®Connect app and select the window symbol for activation or deactivation. VALVE ADJUSTMENT (can only be set in the brennenstuhl®Connect app) If the valve adjustment has been activated in the app, an automatic valve adjustment will be carried out if necessary. The valve adjustment can be activated or deactivated in the app. This function is activated by default. For activation/deactivation, open the brennenstuhl®Connect app, go to the control field of the radiator thermostat and select the valve symbol. CHILD PROTECTION (can be set in the brennenstuhl®Connect app) The child protection can be activated or deactivated in the brennenstuhl®Connect app. If the child protection is active, all settings at the radiator thermostat are blocked. The function is intended to prevent incorrect operation or children playing with the radiator thermostat.
For activation/deactivation, open the brennenstuhl®Connect app, go to the control field of the radiator thermostat and select the padlock symbol. AUTOMATIC MODE – SETTING HEATING PHASE (can only be set in the brennenstuhl®Connect app)
In the brennenstuhl®Connect app, under the radiator thermostat, select the “Clock symbol” for the automatic mode. Afterwards, you can define the individual heating phases. Select “Add timer” and enter the values for the heating phases.brennenstuhl HTCZ01 Zigbee Radiator Thermostat - CHILD
PROTECTION 1

CLEANING THE DEVICE

  • Clean the device with a dry, non-linting cloth. In case of more serious contamination, you can slightly moisten the cloth.
  • Do not use solvent-containing detergents for the cleaning. Otherwise, the surface and labelling of the device may be damaged.
  • Never immerse the device in water or any other liquids. Otherwise, the device may be damaged.
  • Ensure that the device is completely dry before the next use.

DISPOSAL
The packaging is made of environmentally friendly materials which can be disposed of via the local recycling centres. For possibilities of disposal of the used product, please contact your local or municipal administration.
When your product has come to the end of its working life, in the interest of protecting the environment, it should not be disposed of with the domestic waste. Please dispose of it correctly. You can obtain further information on collection points and working hours with your competent administration.
Batteries and rechargeable batteries may not be disposed of in household waste!
As a consumer, you are legally obligated to dispose of all batteries and rechargeable batteries at a collection point in your municipality/your district or in a shop so that they can be disposed of in an environmentally- friendly manner, otherwise there are possible risks to the environment and human health.

SERVICE

If you have questions concerning the product, please do not hesitate to contact us at www.brennenstuhl.com.
Phone: 00 800 48 72 0 74 1 (free of charge)
SIMPLIFIED EU DECLARATION OF CONFORMITY
We, the Hugo Brennenstuhl GmbH & Co.KG, herewith declare that the remote system type HT CZ 01 complies with the directives 2014/53/EU and 2011/65/EU.
The complete text of the EU declaration of conformity is available at the following web address: www.brennenstuhl.com/konformitaetserklaerung/ke_1294070.pdf
This device complies with all legal, national and European requirements.
All company names and product designations contained herein are trademarks of the respective owners.
All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

brennenstuhl User Manuals

Related Manuals