brennenstuhl AL 3050 LED Strahler Instruction Manual

brennenstuhl AL 3050 LED Strahler Instruction Manual

Attention: Before using the product, please carefully read the operating instructions and store them in a proper location!

SAFETY INSTRUCTIONS

1. Always check the product for damage before use. Never use the product in case of any  damage. If this is the case, please refer to an electrician or the manufacturer’s service address.
   Non-compliance poses a risk of fatal injury from electrical current!

2. Do not use the product in potentially explosive atmospheres – danger of death!

3. Keep the floodlight away from children. Children are not aware of the risks imposed by electric current.

4. Please never look directly into the light.

5. A destroyed protective cover cannot be replaced. The floodlight has to be disposed of.

6. The external flexible cable of this lamp cannot be exchanged; if the cable is damaged,  the lamp has to be scrapped.

7. The spotlight must be installed and serviced by a qualified technician.

8. Electrical installations may be performed only in compliance with safety regulations (VDE 0100 for Germany).

9. A VDE-certified connection line must be used for the connection.

10. The spotlight must be properly grounded (with protection class I).

11. If the connection box is damaged, it has to be replaced by a qualified expert.

12. Always switch off the power supply before installation (Fig. 1). Caution: electric shock.

13. Observe the recommended mounting heights (see under Mounting). Hot surface

Not suitable for applications with external dimmers.

TECHNICAL DATA

• Protection class: I
• Protection type (versions without motion detector): IP 44
• Protection type (versions with motion detector): IP 44
• Temperature range: -10 °C to +40 °C

Type| AL 1050| AL 2050| AL 3050| AL 1050 P| AL 2050 P| AL 3050 P
---|---|---|---|---|---|---
Motion detector| No| No| No| Yes| Yes| Yes
Nominal power (W)| 10| 20| 30| 10| 20| 30
Power| 0.09 A| 0.16 A| 0.135 A| 0.09 A| 0.16 A| 0.135 A
Power factor| 0.5| 0.5| 0.9| 0.5| 0.5| 0.9
Dimensions of protective cover (mm)| 118 x 76| 171 x 117| 204 x 140| 118 x 76| 171 x 117| 204 x 140
Dimensions L x W x H (mm)| 93 x 124 x 101| 180 x 135 x 111| 216 x 165 x 136| 150 x 124 x 107| 180 x 194 x 117| 216 x 220 x 136
Weight (g)| 331| 523.8| 754| 399.6| 594.2| 843
Max projected area (m²)| 0.0116| 0.0243| 0.0357| 0.0186| 0.0350| 0.0476

This product is suitable for indoor and outdoor lighting purposes.

The spotlight must be installed at a height of less than 3 m. Recommended installation height for models with motion detector 1.8 to 2.5 m.

The spotlight must not be used for other purposes.

INSTALLATION AND CONNECTION TO POWER SUPPLY

1. Always switch off the power supply before installation ( Fig. 1 ).

2. Installation position: The spotlight should ideally be fastened with the wall bracket.

3. Remove the retaining bracket from the spotlight ( Fig. 2 ).

4. Mark the position of the drill holes for fastening the retaining bracket ( Fig. 3 ) and

5. drill the corresponding holes in the wall ( Fig. 4 ). Fasten the bracket to the wall with suitable screws ( Fig. 5 ).
   
   

6. Bring the connection line in through a cable sleeve with a seal ( Fig. 6.1 ).
   

7. Guide the 3 wires into the screw terminal and screw them all tight ( Fig. 6.2 ). Pay attention to the markings N = blue wire, earthing symbol = green / yellow wire, L = brown wire.

8. Plug the screw terminal into the spotlight’s cable entrance ( Fig. 6.3 ).

9. Push the cable sleeve in toward the spotlight and screw it to the spotlight cable entrance ( Fig. 6.4 ).

10. Fasten the spotlight to the retaining bracket.

11. Adjust the lamp into the desired position and tighten the screws ( Fig. 7 ).
    

12. Switch the power supply back on ( Fig. 8 ).
    

DESCRIPTION OF FUNCTION

(only for versions with motion detector) ( Fig. 9 + 10 )

This lamp is equipped with an infrared sensor. It switches on automatically when the
sensor detects movements in the area. If possible, do not point the motion detector toward swimming pools, heating air extractors, air conditioners or objects subject to strong temperature variations. Avoid directing the motion detector at trees or buses or places where pets frequently are.

The motion detector can be rotated horizontally right and left as well as vertically up and down.

When attaching the spotlight, make sure that the motion detector reacts most sensitively to movements that run across the detection field and least to movements directly toward the device.

ADJUST MOTION DETECTOR

Rotate the mounted spotlight upward. You will see three controls on the bottom of the motion detector ( Fig. 9 ).

SENSITIVITY (SENS, MIDDLE): (Fig. 10)

The sensitivity determines the maximum distance at which the sensor switches on due to a person’s movements.

LIGHT SETTING (LUX, RIGHT): (Fig. 10)

The light setting determines the brightness at which the spotlight’s sensor switches on. The position (sun symbol – right) shows that the sensor works during the day and at night, in the other position (moon symbol – left), the sensor works only at night.

To set, wait until the desired brightness is reached in the surroundings. Set the time sensor TIME to the minimum time (10 sec.). Turn the light setting control completely to the symbol (moon). Turn the control slowly toward the symbol (sun) until the spotlight switches on from movement.

The sensor will not switch on when detecting a motion beginning with the set brightness.

TIME SETTING (TIME, LEFT): (Fig. 10)

With this control, you can select any switch-on time between approx. 10 seconds and 4 minutes after the last movement has been detected. Turning the TIME control in the clockwise direction increases the time period, and reduces it in the anti-clockwise direction.

MOTION DETECTOR: PASSIVE INFRARED SENSOR

Detection range: up to 12 m / up to 180° (horizontal) Time setting: approx. 10 sec. to 4 min.

SCOPE OF DELIVERY

LED-spotlight, operating instructions, screws, dowels.

ACCESSORIES

Suitable accessories are available on our homepage www.brennenstuhl.com.

MAINTENANCE

ATTENTION: The LED lamp does not contain components that require maintenance. The light source in this lamp cannot be replaced; if the light source has reached the end of its service life, the entire lamp has to be replaced. The lamp may not be opened

CLEANING

Before cleaning, disconnect the floodlight from the mains power. Do not use solvents, caustic cleaning agents or similar products. Only use a dry or slightly moistened cloth for cleaning.

DISPOSAL

Dispose of electric appliances in an environmentally friendly manner! Electric appliances must not be disposed of in household waste!

The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment rules that used electric appliances should be collected separately and recycled in an environmentally friendly manner.
For possibilities of disposal of the used appliance, please contact your local or municipal administration.

EU DECLARATION OF CONFORMITY

The EU Declaration of Conformity is deposited with manufacturer.

ADRESSES

Hugo Brennenstuhl GmbH & Co. KG Seestraße 1 – 3 · D-72074 Tübingen
H. Brennenstuhl S.A.S. 4 rue de Bruxelles ∙ F-67170 Bernolsheim lectra technik ag Blegistrasse 13 · CH-6340 Baar

For more information please visit the Service/FAQ section on our homepage,
www.brennenstuhl.com.

References

• brennenstuhl® | Licht- und Stromverteilung

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>