Rebecca 3141-BPW Millennium Lighting Instructions
- June 16, 2024
- Rebecca
Table of Contents
Rebecca 3141-BPW Millennium Lighting
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE : Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT : Do not attach fixture directly to outlet box.
STEP 1 : Secure mounting bar (A) to outlet box with outlet box screws
(B).Thread nut (D) onto nipple (E). Insert lock washer (C) and thread the
nipple (E) onto mounting bar (A), then secure with the nut (D).
STEP 2 : Thread screw collar ring (G) onto nipple (E). Slide screw collar
ring (G) and canopy (F) over screw collar ring (G). Using a pair of pliers,
open the chain link (H) and chain link (J) connect it to collar ring (G),chain
(I) and fixture loop (K),Close the chain link.
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 3 : Lace wires up through chain (H) and pass wires through holes in
screw collar ring (G),We recommend lacing wire up through every other link of
chain (I).
GROUNDING INSTRUCTIONS
STEP 1 : Insert the green grounding screw into the hole with two raised
dimples on the mounting bar. Wrap the ground wire from the fixture (if
supplied) around the green grounding screw, then connect it to ground wire
from the outlet box (if not fixed on the outlet box) using a wire connector
(not supplied). If ground wire from the fixture is not supplied, wrap the
ground wire (if not fixed on the outlet box) from the outlet box around the
green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2 : Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires
according to the directions below:
| GROUP A: Connect to Black House Wire | GROUP B: Connect to White House Wire |
|---|---|
| BLACK | WHITE |
| *PARALLEL WIRE (round & smooth) | *PARALLEL WIRE (square & ridged) |
| WHITE OR GREY WITH TRACER | WHITE OR GREY WITHOUT TRACER |
| BROWN GOLD OR BLACK WITHOUT TRACER | BROWN, GOLD OR BLACK WITH TRACER |
*NOTE : When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
STEP 3 : Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4 : Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel firmness.
STEP 5 : Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check again for
a firm connection.
STEP 6 : Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1 : After wires are connected, tuck them carefully inside outlet
box. Raise canopy (F) allowing for nipple (E) to protrude through the holes on
canopy (F), and secure with screw collar ring (G).
STEP 2 : Thread fixture loop (K) onto nipple (L). then secure with the
fixture loop (K)..
STEP 3 : Install light bulbs. (Please do not exceed the maximum capacity
recommended on the socket.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO:3141-BPW 3141-RBZ
3142-BPW 3142-RBZ
3143-BPW 3143-RBZ
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>