luminii MKR-XX Myka Trimmed Recessed Installation Guide

June 17, 2024
luminii

luminii MKR-XX Myka Trimmed Recessed

luminii-MKR-XX-Myka-Trimmed-Recessed-PRODUCT

Product Information

Specifications:

  • Model: MKR-XX, MKRA-XX
  • Power Requirement: Class 2 Power Unit, 24 Volts DC
  • Installation: Surface Mount Only
  • Environment: Suitable for Damp Locations, Suitable for Installation within Closet Storage Space
  • Safety: Inherently Protected

Product Usage Instructions

Installation by Qualified Electrician:
The product must be installed by a qualified electrician to ensure proper setup and safety.

Power Unit:
Use only with a Class 2 power unit to avoid damage to the product.

Location:
The product is suitable for installation within closet storage spaces.

Voltage:
The product operates on 24 Volts DC.

Environment:
The product is suitable for use in damp locations.

Safety Precautions:
When making modifications to the extrusion and lens, safety equipment is recommended.

Cutting Instructions:
If necessary, the extrusion and lens can be cut in the field using the proper blade for aluminum.

Mounting Brackets:
Mounting brackets are recommended for installation. Different brackets are available depending on the surface type.

LineLED Installation:
Feed the LineLED wires through an opening drilled in the extrusion and remove the adhesive tape backing before installing it onto the extrusion.

Securing LineLED:
Gently press the LineLED strip onto the aluminum extrusion and install the endcaps securely.

FAQ

Q: Can LineLED be shortened?
A: Yes, LineLED can be shortened by cutting along the dashed lines between the solder pads.

Models MKR-XX, MKRA-XX

Please read all instructions before installation and keep them for future reference!

  1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
  2. USE ONLY WITH CLASS 2 POWER UNIT.
  3. 24 VOLTS DC.
  4. SUITABLE FOR DAMP LOCATIONS.
  5. SURFACE MOUNT ONLY
  6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
  7. INHERENTLY PROTECTED

INSTALLATION

luminii-MKR-XX-Myka-Trimmed-Recessed-FIG- \(1\) luminii-MKR-XX-Myka-Trimmed-Recessed-FIG- \(2\) luminii-MKR-XX-Myka-Trimmed-Recessed-FIG- \(3\) luminii-MKR-XX-Myka-Trimmed-Recessed-FIG- \(4\)

  1. Caution : Safety equipment is recommended when modifications are being made to the extrusion & lens.
    If necessary extrusion & lens can be cut in the field. Using the proper blade for aluminum, cut to the desired length.

  2. LineLED can be shortened by cutting along the dashed lines in between the solder pads. Make sure the cut is made on the side of the LineLED without the wire leads. LineLED cannot touch the metal endcap which will shorten the circuit

  3. Mounting brackets are recommended and vary depending on the installation. Reference illustrations below, to determine what bracket is best.
    NOTE : Soft Surface mounting bracket not available on MKRA Channel.

  4. Snap on the hard surface mounting bracket, and screw on the gypsum surface spring bracket. Spread them out evenly, referencing the diagram below.
    NOTE : Soft Surface mounting bracket not available on MKRA Channel.

  5. If necessary route slots on the surface with the proper width and depth to accommodate aluminum extrusion (reference step 7 for slot width).

  6. Gently press the LineLED strip onto the aluminum extrusion and then proceed to install the endaps.

  7. For hard surface mounting brackets: Align the extrusion mounting brackets to the slot, then carefully push the extrusion completely inside to secure.

  8. For the soft surface mounting bracket: Bend the adjustable spring to the straight position, followed by pushing the extrusion completely inside the slot. Then release the springs to secure

  9. Remove the protective film from the diffuser lens. Snap the diffuser lens into the aluminum extrusion.
    NOTE If you are installing the Myka blade louver, please install it carefully. Once the blade louver is installed, it cannot be removed without damaging it.

  10. If installing facing up in wet locations, apply silicone to the edges of the endcaps. Followed by applying silicone to the edge between the lens and extrusion, make sure to clean off any excess silicone.

  11. Ensure the correct (wattage & voltage) power supply is used to power LineLED. Then proceed to connect LineLED wires from the extrusion to the power supply. For more information please refer to the power supply and LineLED wiring instructions.

LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE

7777 Merrimac Ave Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals