Armor 99 Noise Cancelling USB Wired Headset User Manual

: June 17, 2024
: ARMOR

Armor 99 Noise Cancelling USB Wired Headset

Product Information

Specifications

Wideband Speaker
Ear Cushion
Adjustable Headband
Soft Headband Pad
T bar
Ultra Noise Cancelling Microphone
Secondary Microphone
USB Controller
Flexible Boom Arm
Type A Connector

Headset Components

Wideband Speaker
Ear Cushion
Adjustable Headband
Soft Headband Pad
T bar
Ultra Noise Cancelling Microphone
Secondary Microphone
USB Controller
Flexible Boom Arm
Type A Connector

Armor-99-Noise-Cancelling-USB-Wired-Headset-fig-1.

Product Usage Instructions

Compatibility

Works with any PC & Softphone.
Compatible with Skype For Business & Microsoft Teams*, Avaya, Cisco system, and 3CX.

Connection

Connect your Armor 99 USB Series Headset to a free USB port on your PC.
Make sure that the headset has been selected as the standard audio device in the system control audio settings.
Check whether you need to adjust these settings to use a headset by reading the operating instructions for your smartphone application.

Headset Components

Visual Light-Up Display to Mute Microphone
Volume Control
On/Off Hook Key Function for Teams Version

Using Your Headset

Connect your 99 USB Series Headset to a free USB port on your PC. There is a USB Type C adapter included if needed.

Wearing Your Headset

The headset can be worn on either the right or left side by rotating the microphone boom over the headband to accommodate your preference.

How to Wear the Headset

Place the headset receiver to your ear(s), if using a single ear headset you should set the T-bar above the other ear. Adjust the headband until it is comfortable, ideally ensuring that there is virtually no pressure felt on the ear(s).

Mic Positioning

To avoid low or distorted sound, and to provide clear and crisp telephone calls, the microphone should be positioned within an inch or two (30-40mm) from the corner of your mouth. The microphone boom arm is flexible and will move in a variety of directions to ensure the best fit.

Clothing Clip Usage

Your new headset includes a clothing clip to ensure the cable does not get caught or inadvertently pulled. Follow these steps for proper usage:

Fasten the clothing clip securely to your clothing at a suitable level.
Ensure there is enough slack on the cable to allow free movement of your head without disturbing the headset position.

Ear Cushion Removal

To remove the ear cushion for cleaning or replacement, follow these steps:

Using both thumbs, gently pry the ear cushion away from the groove on the receiver.

Maintenance

The ear cushions can be removed for cleaning or replacement Armor-99-Noise-
Cancelling-USB-Wired-Headset-fig-1

Accessories

Replacements & Enhancements:

Leatherette Ear Cushion/s
Spare Foam Ear Cushion/s
Clothing clip
USB Female Type A to Male Type C Adapter
Soft Carrying Case

Safety Information

For your safety, only use this product with CE and RoHS-approved equipment. Using non-approved equipment can void the product warranty.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

NOTE 2

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Regulatory Information

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

Contact Information

Armor Headsets Inc. Website: www.armorheadset.com
Email: info@armorheadsets.com
Phone: 888-880-3088