Trail ARMOR TARZRMFFE900S RZR 4 900 EPS Mud Flap Fender Extensions Instruction Manual

: June 3, 2024
: Trail ARMOR

Table of Contents

Warnings and Product Liability Disclaimer
Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trail ARMOR TARZRMFFE900S RZR 4 900 EPS Mud Flap Fender Extensions Instruction Manual

Warnings and Product Liability Disclaimer

This product is intended to be used as a cosmetic accessory uncle( normal equipment operation and should not be depended upon or used as a safety device Manufacturer assumes no liability for personal injury or equipment damage as the result of use or installation of this accessory User assumes at ask. User should carefully read all instructions on or to installation All Trail Armor products are designed, engineered, and fit to new vehicles and their specifications. Damage, modifications. and extreme wear may cause and require modifications to the product and/or your vehicle to insure proper fitment.

Instructions

Front

A. Locate the driver’s side front fender extension. Notice the three slotted holes at the lower portion of the fender extension. Place the three slotted holes over the three OEM tabs on the fender flare. Push fender extension inward so that the slotted holes are snug behind OEM tabs. See Picture 1, Insert a supplied #10 x ‘1/4 Phillips fiat top screw into the pre-drilled hole located near the OEM tabs See Picture 1. Be sure the bends of the fender extension are pressed into place to fit the OEM flare properly before installing the last seven screws detailed in Steps B and C below.
Instructions

B. Push fender extension tight into the upper bend of fender flare. Be sure inner edge of fender extension is flush with OEM fender flares inner edge. Insert supplied #10 x3/4 Phillips head screw and speed nut into the pre- drilled hole on the lower portion of the top bend. See Picture 2. Insert two supplied #10 x ‘1/4 Phillips head screws and one speed nut into the two lower pre-drilled holes. See Picture 3.

C. At the front pre-drilled hole of the fender extension near the headlight, align the inner edges of both fender extension and OEM panel. Insert #10 x 3/4- Phillips head screw into front hole and install speed nut. See Picture 4. Next. install three #10 x %’ Phillips head screws and speed nuts to finish installation of driver’s side front fender extension. See Picture 5. Do not over tighten. Repeat other side.

Rear

A. To install the drivers side rear mud flap fender extension, remove the two OEM push pins located inside of the lower portion of the OEM fender flare. See Picture 6. After OEM push pins are removed, pull outward on the lower portion of the flare (to ease installation) and install two supplied 1/4″-20 extruded u nuts over the OEM holes located behind the OEM fender flare. See Picture 7. Locate the driver’s side metal mounting bracket (L). Holding the bracket into place. insert two supplied 114-20 X 1 ton( truss machine screws through the bracket and into the previously installed 114″-20 extruded u nuts. Do not over tighten. See Picture 8.

B. Once the metal mounting bracket (L) is in place, install two supplied 1/4″-20 extruded u nuts onto the mounting bracket See Picture 9. Locate the driver’s side rear fender extension While holding the fender extension into position, insert two supplied 1/4-20 X 5/8 torx truss machine screws through the two lower holes of the fender extension. See Picture 10. Locate the pre-dnlled hole just below the first bend of the fender extension. Make sure the inside edge of the Trail Armor fender extension is flush with the edge of the OEM fender flare. Insert one supplied #10 X 3/4 phillips flat top screw through this pre-dnlled hole into the OEM fender flare. Install one supplied speed nut over screw end and tighten. Do not over tighten. See Picture 11. Insert one supplied #10 X 3/4 phillips flat top screw into the predrilled hole below the previously installed screw. Install one 8-32 speed nut over screw end. See Picture 12.

C. Locate the pre-drilled hole just above the first bend of the fender extension. Holding the edge of the fender extension flush with the OEM fender flare (on the interior), insert four supplied #10 X 3/4 phillips flat top screws through the pre-dnlled holes in the fender extension into the OEM fender flare. Install four 8-32 suplied seed nuts over screw ends. Do not over tithten. See Picture 13.
Instructions
Original August 13, 2014
Enjoy! Any questions. contact Trail Armor at 6624624222