SteamSpa SC-SS0012-0SIndoor Hemlock Wood FAR Infrared Sauna User Guide

SteamSpa SC-SS0012-0SIndoor Hemlock Wood FAR Infrared Sauna

Specifications

• Model: SC-SS0012-0S
• Type: Infrared Sauna
• Version: v1.1

Product Usage Instructions

1. Check for Damages: Upon delivery, inspect the sauna for any visible damages. Report any issues with the packaging to the shipping company and SteamSpa’s Customer Service Department.
2. Verify Model and Accessories: Ensure that the sauna model and accessories match your order and check the voltage input. Notify SteamSpa’s Customer Service Department within 48 hours in case of any discrepancies
3. Read Installation Instructions: Thoroughly review the installation instructions provided to ensure a secure and effective setup of your SteamSpa sauna.
4. Installation Disclaimer: It is important to note that SteamSpa will not be liable for any product damage or malfunction resulting from self-installation or non-compliance with the user manual’s installation guidelines.

Frequently Asked Questions (FAQ)

• Q: How do I register my product for warranty coverage?
  A: You can register your product online at www.SteamSpa.com/register or by mailing in the completed registration card to the provided address. Ensure registration is done within 90 days of purchase to activate the warranty.

• Q: What should I do if I notice damages during delivery?
  A: If you observe any damages to the sauna packaging upon delivery, report it immediately to the shipping company’s representative and SteamSpa’s Customer Service Department.

• Q: Can I install the sauna myself?
  A: While self-installation is possible, it is recommended to strictly follow the installation instructions outlined in the user manual to prevent product damage or malfunction.

INFRARED SAUNA USER GUIDE

MODELS
SC-SS0012-0S

DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your sauna is warranty coverage.
Mail in the completed registry card (Pg. 2) or register online at www.SteamSpa.com/register.

PRODUCT REGISTRATION

IMPORTANT: Your warranty will not be recognized unless this card is fully completed and returned or online registration is completed.

To ensure that your warranty is registered and confirmed please do one of the following:

1. Register online at www.SteamSpa.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information.
2. Complete, cut-out and mail the registration card below. By your returning card we confirm the date of purchase for your new product. This confirmation will allow us to process any warranty claims.

Mail the card to: 5701 NW 35 Avenue, Miami, FL 33142

IMPORTANT WARRANTY INFORMATION!
WARRANTY AND REPAIR GUIDELINES
SteamSpa warrants that this sauna unit will be free from manufacturer defects and malfunctions. For terms and conditions please refer to latest SteamSpa Warranty at www.SteamSpa.com/warranty.
Please be advised failure to comply with any of the following will VOID the warranty.
1. Sauna must registered within 90 days of delivery. See www.SteamSpa.com/register.

Warranty Period:
This product is covered under warranty for a period of one year, commencing from the date of purchase.
For further information or assistance, visit www.SteamSpa.com/warranty or call 1-800-856-0172.

IMPORTANT!

• Malfunctions, damages, part replacements and labor resulting from improper installation, negligence, or lack of care and maintenance will NOT be covered under the SteamSpa Warranty.
• PRIOR TO INSTALLATION,ENSURE THAT THE PRODUCT IS POWERED OFF.

Thank You for choosing SteamSpa for health, beauty and relaxation. Now you can enjoy your own private sanctuary in the comfort of your own home.

USER INSTRUCTIONS

1. Check for visible damages upon delivery of sauna. Any damages to packaging should be reported immediately to shipping company delivery representative and SteamSpa’s Customer Service Dept.
2. Check model and accessories are correct, including voltage input. Any discrepancies are to be reported to SteamSpa’s Customer Service Dept. within 48 hours of delivery.
3. Read installation instructions in detail for a secure and effective installation of SteamSpa sauna.
4. SteamSpa shall not be responsible for product damage or malfunction caused by self-installation or installation procedures which do not comply with user manual.
5. SteamSpa saunas are for indoor use only.

WARNING
Please read carefully before using sauna

• DO NOT use the sauna product with any of the following Health Conditions:

  1. Any type of respiratory condition
  2. Any type of a heart condition
  3. High or low blood pressure
  4. Pregnancy
  5. Any skin disease or disorders
  6. After or while drinking alcohol or alcoholic beverages
  7. Hemophilia or are prone to bleeding

• Check with your doctor regarding the use of this product if you have any other health conditions.
  Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6°F ( 37°C ). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:

  • Failure to preceive heat
  • Failure to reconize the need to exit, or Physical inability to exit the room
  • Unawareness of impending hazard
  • Fetal damage in pregnant women
  • Unconsciousness

WARNING
Please read carefully before using sauna

• Children must use the sauna under the care of an adult. For safety, do not play with it.
• Do not insert objects such as fingers or sticks into the heating tube plate to prevent danger. Never pour water in the sauna especially the heating board.
• Do not place items inside or on top of the sauna.
• Do not touch any electrical components with wet hands to prevent electric shock.
• Do not use the sauna during thunderstorms to prevent electric shock.
• Do not tilt the sauna, do not use sharp objects to strike the sauna.
• Shut down the sauna for half an hour after 4 hours of continuous use.
• Do not operate the sauna in a long-term high temperature environment.
• Do not use after intense exercise, wait until the body temperature returns to normal before using. If you feel any discomfort, please stop using immediately.
• Mind your head when getting in and out of the sauna.
• Do not sleep inside when the sauna turned on.
• Do not use any bath products in the sauna.
• To avoid burns, do not touch the heating element.
• Please keep the seat timber and floor heater dry to avoid damage!
• Do not take pets into the sauna room.
• Do not spray water on the radiators, This may result in electric shock or damage to the radiators. Do not touch the light bulb in use.
• lf the bulb needs to be changed, unplug the sauna and let the bulb cool down before changing it. Do not use the sauna room if you have a trauma, eye disease or burns.
• Do not install shower heads or water spray devices above or inside the sauna.

Covering the heater or infrared emitter causes fire risk!

ASSEMBLY TIPS

Before you begin, read all assembly instructions and safety warnings carefully.

• This sauna requires at least 2 adults to complete assembly.
• Remove all of the contents from the package and check that you have all parts shown in the compoment list.
• NOTICE: Some parts may be pre-installed / pre-assembled.
• This manual is used for the assembly of several sauna models, some figures or drawings may not look exactly like your sauna. Protect the wood surface of sauna during assembly to avoid damage.
• Keep this manual for future reference.

ELECTRICAL REQUIREMENTS

• It is recommended to consult a licensed electrician and check local ordinances before installing any sauna. This sauna requires that receptacle and circuit breaker specifications are 20 amp.
• Electrical modifications may be required to adapt 20 amp current.
• This sauna requires a dedicated circuit, other appliances may not share the same outlet as the sauna.

CHOOSING A LOCATION

• This sauna should be placed INDOORS on a dry, level surface only.
• There should be a minimum of 5 inches clearance between the sauna and any wall.
• Make sure the main power cord will reach the outlet and remains easy to access.
• The sauna should only be used in a dry location, moisture will damage the wood and electrical components.
• Keep the sauna away form any potential hazards including water sources, flammable objects and combustible materials.

RECOMMEND TOOLS

1. Pencil
2. Hammer
3. Tape Measure
4. Electric Drill
5. “+” screwdriver

SPECIFICATIONS

1900mm )
Power Output| 2300 Watts
Maximum Temperature| 149°F ( 65°C )
Voltage| 120V AC / 60Hz
Function| **** Control panel with temp adjust and timer, Audio with USB Drive/Bluetooth/FM, Color LED light, Oxygen ionizer

PRODUCT SIZE CHART

COMPONENTS

1. Duster cover
2. Control box
3. Temperature sensor
4. Left board
5. Control panel
6. Front board
7. Window glass
8. Handles with screw x2
9. Door glass
10. Hinge
11. Bottom board
12. Top board
13. Ventilation
14. Backboard
15. Right board
16. Bench
17. Bench front board
18. Foot rest board
19. Ventilation

Accessories

INSTALLATION

NOTICE:
Please read WARNING and ASSEMBLY TIPS section before installing the sauna.
The figures and drawings are used for the assembly guide only, parts and accessories may not be consistent with your sauna.

1. Find a location to place the Bottom board [11], see ASSEMBLY TIPS for details. Then Attach the Front board [6] to the Bottom board by lining up the Front board with the edge in front of the Bottom board. (Fig 1)

2. There are two kinds of buckles during whole installation, install as shown. (Fig 2)

3. Attach the Right board [15] to the Front board by aligning the buckles and sliding the Right board down, locking it into place. (Fig 3)

4. Attach the Left board [4] to the Front board by aligning the buckles and sliding the Left board down, locking it into place. (Fig 4)

5. Attach the Back board [14] to the Bottom board by aligning the buckles of Left board and Right board, and sliding the Right board down, locking it into place. (Fig 5)

6. Slide the Bench front board [17] into the grooves on Left and Right board as shown (Fig 6), connect the power cable as shown (Fig 7).

7. Put the Bench [16] on the Bench front board, and push it forward to Back board, then fix the bench with self-tapping screws (450).(Fig 8)
   Then put the Foot rest board [18] on the Bottom board, fix the Foot rest board with self-tapping screws (335).

8. Lead the wires in the sauna to the top, Install the Top board [12] at the top of the sauna (Fig 9), and let wires through the groove of Top board.

9. Every connection cable or plug has a corresponding pair, find male and female with the same label (like “Control”) and plug in correctly.

10. Find the “12V output” wire from Control Box [2], through the hole on the Back board, and connect the Oxygen Ionizer (independent parts), then use Electric drill to fix the Oxygen ionizer on the Back board with self-tapping screws (3*25).
    (Fig 11)

11. There are some holes at the edges around the Top board, use Self-tapping screws (5*50) to fix the Top board. (Fig 12)

12. Put the Duster cover [1] on the Top board, then fix the Duster cover with self-tapping screws (3*25) at the four corners. (Fig 13)
    NOTICE: If the duster cover in the package comes in two pieces, you need to fix screws at the optional positions as shown. 

13. Seperate Handles [8] by unscrewing screws on the screw side. Screw side is for inside of Door glass [9], another side is for outside. (Fig 14)
    Put the both handle align with the holes in Door glass, and fix the handle with screws at the wooden handle.

14. Plug the main electrical cord into a dedicated outlet.
    NOTICE : The power outlet should be dedicated to the sauna. Do not

INSTRUCTIONS FOR USE

Congratulations, the assembly of the sauna is now complete, Please review instrutions, warnings & suggestions before using.

1. Temperature display screen
   Display the temp in sauna room, If temp is lower than 86°F (30°C), it shows “LO”.

2. Timer display screen
   If timer is activated,display the countdown time.

3. USB port
   Plug in USB drive, use Audio function to play the music in USB drive.
   NOTICE:

4. The partition format of USB drive require FAT32.

5. MP3 audio should be placed in the root directory.

6. Light button
   Press the button to turn on/off the light, the indicator light will show the ON/OFF status of the light in sauna (if available). If the indicator is on, press the button 5s will turn to lamp adjust mode, Timer display will show “2n”, in this mode, the ON/OFF status of color light
   can be adjusted:

7. press “Time-” to turn ON/OFF color light, and press “Time+” to turn ON/OFF the light in sauna.

8. If the color light is on, short press light button to change the color.

9. No operation for 8s quits the light adjust mode.

10. Power button
    Press and hold this button to switch heater ON / OFF.

11. Temp control
    Press TEMP- and TEMP+ to adjust the heater temperature.
    Temperature range is 86-149°F [ 30-65°C ], press once adjust 5°F [ 1°C ].
    Celsius/Fahrenheit display switch: Press “TEMP-” and “LOCK” for 5S.

12. Timer control
    Touch the “TIME+” and “TIME-” buttons to set the timer.

13. Audio control
    The sauna can play music or radio, press to audio adjust status.
    In audio status, indicator will on, Temp diplay show audio source, Timer display show volume(”Db”, range 01-30), press “TIME+” or “TIME-” to adjust volume, press audio button for switch audio source. No operation for 8s quits the audio adjust mode.
    Bluetooth: Temp display shows “BLU”. Use devices that support Bluetooth audio playback(e.g. smartphone), find the bluetooth device called
    “Steam Spa”, click to connect. If connect successful, press “TEMP+” and “TEMP-” to switch previous / next music.
    NOTE : During bluetooth match, cannot swich audio source or turn ON/OFF another function.
    USB drive: Temp display shows “USB”, press “TEMP+” and “TEMP-” to switch previous / next music.
    FM Radio: Temp display shows frequency, time display shows “VOL”. Press “TEMP+” and “TEMP-” to adjust FM frequency (85.7-108.0Mhz). OFF: Audio function will turn off.

14. Button lock function
    Long press the button for 5s to lock / unlock the control panel.

Oxygen ionizer

1. Press ion button to turn ON/OFF ion function.
2. Press ozone button to turn ON/OFF ozone function.

Tips

1. The speaker is on the bottom of Top board, the audio quality is even better in the sauna.
2. Control box may be hot during sauna session, do not cover.
3. If the radio audio quality is poor, try to adjust the antenna.
4. Ceiling vent can be adjusted in the sauna.
5. When activated, the ozone/ionizer may a produce a distinct odor.

SUGGESTIONS

Before using

1. Please be sure to follow the instruction manual before operations.
2. A hot shower or bath prior to the start of your sauna session, will help promote perspiration.

During using

1. STAY HYDRATED! Remember to drink plenty of water before, during and after your sauna.
2. A normal sauna session should last 30 minutes or less.
3. Perspiration will begin within 15-25 minutes.
4. Open the ceiling vent or door to allow fresh air into the sauna.

After use

1. Always remember to unplug your sauna after each use.
2. Open the door to let the heat and humid water vapor dissipate and keep the sauna cabin dry.
3. Make sure to wipe any sweat from the sauna walls and surfaces. We recommend using a towel.

Clean wood parts

1. Use a wrung wet towel to wipe down the cabin’s outer and inner surface. Additionally, we recommend running a small vacuum cleaner on the inner surfaces.
2. Avoid the use of any organic based cleaners such as gasoline or alcohol on the sauna’s wooden surfaces.
3. Avoid using any sharp or abrasive materials to prevent scratching the wooden surfaces.

Cleaning glass parts

1. Use soft materials to wipe the glass such as a micro-fiber washcloth.
2. Stubborn stains can be wiped with a damp cloth, then dry with a dry cloth.
3. Void using any sharp or abrasive materials to prevent scratching the glass surfaces.

Transportation and storage

1. Avoid water, snow and intense impact during the transportation.
2. Do not store it in a humid environment.
3. The northern climate is relatively dry, keep the wood parts humid, for example, wipe the product with a wrung wet towel.

TROUBLE SHOOTING

The indicator light is broken.

Indicator light is not working.

| The circuit board or components are broken.| **** Contact SteamSpa service.
The temperature sensor is broken.

Infrared Heater not heating up.

| The heater is broken.| Contact SteamSpa service to replace heater .
The wire junction or the heater’s wire is loosened.| Check and tighten the connection.
The temperature sensor is broken.| **** Contact SteamSpa service.

**** Odor from the sauna.

| **** The circuit‘s problems, or foreign matter is heating.|

1. There is foreign matter around, remove it.
2. Heater is over heated or some parts are damaged, cut off the power supply, contact SteamSpa service.

Display shows error code.

| EO: Temp sensor is open circuit or breakdown.| Contact SteamSpa service.
HH: Temp in sauna is too high.| Stop using, let sauna cooldown, if display again, contact SteamSpa service.
Er3: Ambient temp lower than 5°F.| Raise ambient temperature.

**** Cannot play music or radio.

| **** Cannot read USB drive.| Check partition format of USB drive

is FAT32, or change another USB drive.

Bluetooth device connect failed.| Change another Bluetooth audio device.
FM signal strength is not good.| Try to adjust the antenna on top board.

**** Light is not working.

| Wire is not well connected.| Check the connecting wire.
The light is damaged.| Contact SteamSpa service.

Steam Spa PHONE: 305-614-4070 FAX: 866-560-1060 http://steamspa.com info@steamspa.com

References

• Register | SWCORP

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>