i Armor IA-S116H Stainless Steel Nerf Bars Pocket Steps Square Installation Guide

June 1, 2024
i Armor

i Armor Logo iArmor®by APS

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMEND- ED. THANK YOU FOR CHOOSING OUR PRODUCT!
ROCKER PANEL MOUNT
NO DRILLING / TRIMMING REQUIRED

Torque Value

Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

i Armor IA-S116H Stainless Steel Nerf Bars Pocket Steps Square - PART
LIST

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 4| U Brackets| 6#| 4| M8 Nylon Lock Nuts
2#| 8| M8X1.25-35mm Hex Bolts| 7#| 8| M6X1-25 Hex Bolts
3#| 4| M8 Large Flat Washers| 8#| 16| M6 Large Flat Washers
4#| 4| M8 Lock Washers| 9#| 8| M6 Nylon Lock Nuts
5#| 8| M8 Flat Washers| | |

i Armor IA-S116H Stainless Steel Nerf Bars Pocket Steps Square - Hardware
Package

Hardware Package B (For Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 4| M8X1.25-55mm Carriage Bolts| 3#| 4| M8 Lock Washers
2#| 4| M8 Large Flat Washers| 4#| 4| M8 Hex Nuts

i Armor IA-S116H Stainless Steel Nerf Bars Pocket Steps Square - Step
BarThe instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation.
STEP 1
Start installation from the passenger side front of the vehicle.
Assemble the Passenger Front Mounting Bracket (PFM) and Passenger Front Support Bracket (PFS) as shown, (Fig 1). Do not fully tighten hardware at this time. (Fig 1) Passenger Front Mounting Bracket Assembly

STEP 2
Locate the Passenger Side Front Mounting position on vehicle, there are (2) holes on the pinch weld and one threaded hole on the bottom floor, (Fig 2). (Fig 2) Passenger Side Front Mounting Location
STEP 3
Attach the Assembled Passenger Front Mounting Bracket on the mounting position (Fig 3). Specifically mount Passenger Front Mounting Bracket (PFM) on the bottom threaded hole with (1) M8X1.25-35mm Hex Bolt, (1) M8 Large Flat Washer and (1) M8 Lock Washer. Install Passenger Front Support Bracket (PFS) on the pinch weld with (2) M6X1-25mm Hex Bolt, (4) M6 Large Flat Washers, and (2) M6X1 Nylon Lock Nuts. Do not fully tighten hardware at this time. (Fig 3) Passenger Front Mounting Bracket Installed

STEP 4
Move to the rear of the vehicle. Assemble the Passenger Rear Mounting Bracket (PRM) and Passenger Rear Support Brackets (PRS) with (1) M8X1.25-35mm Hex Bolt, (2) M8 Flat Washers and (1) M8X1.25 Nylon Lock Nut, (Fig 4). Do not fully tighten hardware at this time. (Fig 4) Passenger Rear Mounting Bracket Assembly
STEP 5
Locate the Passenger Side Rear Mounting position on vehicle (Fig 5). Attach the Assembled Passenger Rear Mounting Bracket on the mounting position. Mount Passenger Rear Mounting Bracket (PRM) on the bottom threaded hole with (1) M8X1.25-35mm Hex Bolt, (1) M8 Large Flat Washer and (1) M8 Lock Washer. Install Passenger Rear Support Brackets (PRS) on the pinch weld with (2) M6X1-25mm Hex Bolt, (4) M6 Large Flat Washers, and (2) M6X1 Nylon Lock Nuts, (Fig 6). Do not fully tighten hardware at this time. (Fig 5) Passenger Side Rear Mounting Location (Fig 6) Passenger Rear Mounting Brackets Installation

STEP 6
Once all (2) passenger side mounting brackets are installed, select and attach the Passenger Side Step Bar onto the Mounting Brackets with (2) U Brackets, (2) M8X1.25-55mm Carriage Bolts, (2) M8 Large Flat Washers, (2) M8 Lock Washers and (2) M8X1.25 Hex Nuts, (Fig 7). Do not fully tighten hardware at this time.
STEP 7
Properly level and adjust the Step Bar and fully tighten all hardware.
STEP 8
Move to the other side of the vehicle. Repeat Steps 1-7 to install driver side step bar.
Installation completed.
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

NOTE: Torque all M8 X1.25-55mm Carriage Bolts to 16~18 Ib-ft. Don’t over tighten, or the square bars will be damaged by the brackets i Armor IA-S116H
Stainless Steel Nerf Bars Pocket Steps Square - damaged

Customer Support: info@iarmorauto.com
Rev. 20231101 i Armor Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals