Trail ARMOR TAMFFE-TEXTRON-XX Textron XX Mud Flap Fender Extensions Instruction Manual

: October 27, 2023
: Trail ARMOR

Table of Contents

Installation Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trail ARMOR TAMFFE-TEXTRON-XX Textron XX Mud Flap Fender Extensions

Installation Instructions for Textron XX Mud Flap Fender Extensions
TAMFFE-TEXTRON-XX

Installation Instructions

Warning and Product Liability Disclaimer

This product is intended to be used as a cosmetic accessory under normal equipment operation and should not be depended upon or used as a safe device. Manufacture assumes no liability for personal injury or equipment damage as the result of use or installation. PLEASE NOTE: This Product was designed, fit and tested on new vehicle specifications. Any damage, modifications or excessive wear to your vehicle may require modification to the product and/or your vehicle to ensure proper fitment.

To Install Rear Extensive

A. Locate the factory screw from the lower front of the rocker panel. Remove and discard. See Picture 1.

B. Locate the Trail Am1or passenger side rear fender extension and one supplied m6-1.0x 25mm bolt. Holding the extension into position, install the 25mm bolt through the lower pre-drilled hole of the extension into the hole where the factory screw was previously removed. Refer back
to Picture 1

C. Starting with the first tab above U1e 25mm bolt, use a pencil to mark the center of the tabs. After marking centers of the tabs, mark 5/8″ from the edge of the factory fender. See Picture 2A and 28. Using a ‘/4” drill bit, hold U1e extension tight against the factory fender, drill a ¼” hole at the intersection ofU1e two marks. Make ~re hands are away from where you are drilling!

D. Locate one supplied ¼-20 x 518″Torx Truss screw and one supplied ¼-20 nylock nut. Insert the 5/8″ screw through the factory fender, though U1e Trail Amnor extension, and secure with the 1 /4-20 nut. See Picture 3.

E. Working around the fender, repeat this procedure for each oft11e 0U1er eight tabs making sureU1e extension is held tight against U1e factory fender. See Picture 4.

F. Locate the two factory screws in the rear side lieat sltield and remove temporarily. See Picture 5A. Locate the supplied passenger side metal support bracket. Slide the bracket behind the heat shield and replace die two factory screws and nuts. Usit1g die ¼” drill bit, drill through die remaining hole of the support bracket and though the extension. See Picture 5B. Locate one supplied ¼-20 x 5/8″ Torx Truss screw and one supplied ¼-20 nylock nut. Insert tl1e 5/8″ bolt through the top oftl1e extension, through the support bracket, and secure with the 1 /4-20 nylock nut.

To install Front Extensions

H. Locate the facto1y screw in the rocker panel and remove temporarily. Locate the Trail Annor passenger side front tender extension. Holding the extension into position, insert the factory bolt U1rough the lowest hole on the extension into the hole where the factory bolt was removed. See Picture 6.

I. As was done on the rear 0ares, mark the tab centers and measure the 5/8″ from U1e factory fender edges. Start with the closest tab, drill the ¼” hole. Again, BE CAREFUL of placement of your hands! Locate one supplied ¼-20 x 5/8″Torx Truss screw and one supplied 1/..-20 nylock nut. Insert the 5/8″ screw through the factory fender, through the extension, and secure with the nylock nut. See Picture 7 A. Also, locate one supplied #10 x ¾” Phillips Oat washer head screw. Insert the ¾” screw into the pre-drilled hole just above the factory screw. See Picture 78.

J. As witl1 tl1e rear extensions, work aro1md the fender for the four remai11ing side tabs. See Picture 8. Before installing the front two, locate the factory screw underneath the front of the fender. Remove temporarily, insert through the extension and back into the factory hole. See Picture 9.

K. Once the factory screw is replaced, the two remaining tabs can be installed. The factory screw may have to be removed to achieve the ”perfect” fit on the front tab. See Picture 10.