i Armor IA-S177H 6.5 Inch Side Armor Stainless Steel Running Boards Instruction Manual
- June 1, 2024
- i Armor
Table of Contents
i Armor IA-S177H 6.5 Inch Side Armor Stainless Steel Running Boards
Product Information
Specifications
- Mounting Type: Rocker Panel Mount
- Torque Values:
| Fastener Size | Tightening Torque (ft-lbs) |
|---|---|
| 6mm | 6-7 |
| 8mm | 16-18 |
| 10mm | 31-32 |
| 12mm | 56-58 |
| 14mm | 92-94 |
Frequently Asked Questions
- Q: Is drilling required for installation?
- A: No, drilling is not required for mounting this product.
- Q: Can I install this product on my own?
- A: While self-installation is possible, we recommend seeking assistance for best results.
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. THANK YOU FOR CHOOSING OUR PRODUCT!
ROCKER PANEL MOUNT
DRILLING NOT REQUIRED
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package A (For Bracket Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 4 | Driver & Passenger Front/Rear Mounting Brackets | 5# | 18 | M8 Large Flat |
Washers
2#| 2| Driver & Passenger Center Mounting Brackets| 6#| 12| M8 Lock Washers
3#| 6| U Brackets| 7#| 6| M8 Clip Nuts
4#| 12| M8X1.25-25mm Hex Bolts| 8#| 6| M8X1.25 Hex Nuts
Hardware Package B (For Step Bar Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 6 | M8X1.25-55mm Carriage Bolts | 3# | 6 | M8 Lock Washers |
| 2# | 6 | M8 Large Flat Washers | 4# | 6 | M8 Hex Nuts |
Installation Instructions
The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation.
STEP 1
- Identify the passenger side mounting locations as shown, (Fig 1).
STEP 2
- Slide (1) M8 Clip Nut into the rectangular opening with the nut towards the inside. Line up the threaded nut on the clip with the round hole, (Figs 2-3).
STEP 3
- Attach the Passenger Front Mounting Bracket to the installed M8 Clip Nut with (1) M8X1.25-25mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat Washer, (Fig 4). Align the bot-tom hole on the front Bracket with the (1) hole on the pinch weld. Secure the Bracket to the pinch weld using the included (1) M8X1.25-25mm Hex Bolt, (2) M8 Flat Washers, (1) M8 Lock Washer and (1) M8X1.25 Hex Nut, (Fig 4). Do not tighten hard-ware at this time.
- Repeat this step for Passenger Center and Rear Mounting Brackets Installation, (Fig 5). .
Note
- Passenger Front Mounting Bracket and Passenger Rear Mounting Bracket are Universal.
STEP 4
Once all (3) passenger side mounting brackets are installed, select and attach the Passenger Side Step Bar onto the Mounting Brackets with (3) U Brackets, (3) M8X1.25-55mm Carriage Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3) M8X1.25 Hex Nuts. Do not fully tighten hardware at this time, (Fig 6).
STEP 5
- Properly level and adjust the Step Bar and fully tighten all hardware.
STEP 6
- Move to the driver side of the vehicle. Repeat Steps 1-5 to install the driver side step bar.
- Installation completed.
Attention
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
- In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support: info@iarmorauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>