TONOR TW515 Wireless Microphones User Manual

UHF Wireless Microphone Instruction Manual
TW515 / TW525

TW515 Wireless Microphones

ABOUT THIS MANUAL
Thank you for purchasing TONOR wireless microphone. This manual is intended to help you understand all about this microphone and how to use it. TONOR always strives for the ultimate user experience. All our knowledge and passion for audio technology are incorporated into building microphones with high performance for you. The TONOR microphone is high quality and easy to use to achieve the best user experience.
Enjoy your microphone!
TONOR Team

Package Including

OPERATING ENVIRONMENTS & NOTES

When using this device, keep it away from water.
Use the device in ventilated environment, keep it away from fire.
Since it’s a wireless device, please keep it away from other interfering sources.
Don’t take apart the device.
Please use the standard power supply, high voltage may damage the device.
Please place the used batteries into the recycle bin, don’t litter them.

SPECIFICATIONS

Frequency Response: 40Hz-18Khz
Operating Frequency: A: 520.5MHz-549.5MHz; B: 550.5MHz-579.5MHz
Operating Range: Up to 60m
Frequency Stability: ±10ppm
SNR: ≥96dB
Sound Distortion: ≤0.03%
Mic Input Sensitivity: -52dB±3dB(0dB=1v/μ bar at 1KHz)
RF Sensitivity: -95dBm
Operating Temperature: 0˚C to +55˚C

MICROPHONE OPERATION INSTRUCTION

As shown in the pictures:

1. Display Screen
2. ECHO-/ECHO+
3. Treble-/Treble+
4. Bass-/Bass+
5. Volume -/Volume +
6. Power Button
7. Tail Tube
8. Setting Button
9. Battery Compartment

Install 2*AA batteries before using the wireless microphone and installing instruction is as follows:

1. Take down the tail tube of mic.
2. Install the batteries and tighten tail tube of mic.
   Note: The positive and negative polarity of battery cannot be reversed.

Instruction:

1. Press button 6 for 2s to turn it on/off.
2. Press the button 8, then the frequency on the screen wilI be changed.
3. Press button 5 to adjust volume.

RECEIVER INSTRUCTION FOR TW515 AND TW525

1. POWER BUTTON
2. BATTERY INDICATOR
3. USB-C CHARGING PORT
4. SIGNAL INDICATOR

LIGHT INSTRUCTION
Signal light 4
Turns off: The receiver is not connected to the microphone.
Stays on red: The receiver and microphone A are successfully connected.
Stays on green: The receiver and microphone B are successfully connected.
Battery indicator 2
Red and green lights: Power on and charge. (It is not recommended to power on and charge.)
Stays on red: Power off and charge. When the receiver is fully charged, the red light turns off.
Stays on green: The receiver is power on. The receiver is fully charged.
Turs off: The receiver is power off.

TROUBLESHOOTING

No sound for TW515 (The batteries of microphone have already been installed, but the signal light still turns off.)
Wireless Microphone ID Pairing Steps:

1. Make sure that the receiver and microphone are turned OFF.
2. Unscrew the microphone tail tube and install the batteries into the mic’s battery compartment.
3. Turn on the microphone, and press setting button ⑤ (on the microphone), until the microphone screen flashes quickly, then release settting buttons.
4. Turn on the receiver’s power button, waiting for red signal light flashing 4 times, then press the setting button ⑤ (on the microphone) once. The microphone screen becomes steady and no longer flashes, the signal light on the receiver turns steady, indicating that the pairing is successful.
5. Tighten the microphone tail tube. Pairing is now completed.

No sound for TW525 (The batteries of microphone have already been installed, but one of the microphone has on sound.)
Wireless Microphone ID Pairing Steps:

1. Make sure that the receiver and microphone are turned OFF.
2. Unscrew the microphone tail tube and install the batteries into the mic’s battery compartment.
3. Turn on the microphone, and press setting button ⑤ (on the microphone), until the microphone screen flashes quickly, then release settting buttons.
4. Turn on the receiver’s power button, waiting for signal light flashing 4 times( red light for A mic and green light for B mic), then press the setting button ⑤ (on the microphone) once. The microphone screen becomes steady and no longer flashes, the signal light on the receiver turns steady, indicating that the pairing is successful.
5. Tighten the microphone tail tube.
6. Pairing is now completed for one mic, then repeat 2-5 steps for another mic pairing.

Received signal with noise or interference
Change to other channels;
Check if receiving distance exceeds the maximum range.
Microphone cannot be turned on
Check if batteries are installed reversely;
Change to new batteries.

WARRANTY

TONOR provides 2 years of after-sales service, free replacement to products that are NOT damaged resulting from accident, alteration, misuse, negligence, or abuse. If exceeding 30 days of Amazon return policy, you can still contact us through our Shopify TONORMIC. We will serve you with full sincerity!

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0 cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.
https://www.tonormic.com
support@tonormic.com

EASTWEST ELECTRONIC COMMERCE CO.,
LIMITED
LEVEL 54 HOPEWELL CENTRE 183 QUEEN’S ROAD EAST HONG KONG
EASTWEST ELECTRONIC COMMERCE CO US LIMITED
3500 SOUTH DUPONT HIGHWAY, SUITE G106
DOVER, DE 19901 UNITED STATES
LIFEWIT LIMITED
FLAT 237, 233 HIGH STREET CROYDON SURREY
ENGLAND CR0 1FY UNITED KINGDOM
Lifewit GmbH
Friedenstraße 5 97072 Wuerzburg Germany
MADE IN CHINA

References

• Professional USB Microphone and Wireless Microphone – TONOR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>