HOOKE ROAD BXG.8200-S Earthshaker Front Bumper with Bull Bar and Winch Plate User Manual
- June 17, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD BXG.8200-S Earthshaker Front Bumper with Bull Bar and Winch
Plate
Product Information
Specifications:
- Product Name: Front Bumper
- Model: BXG.8200-S
Accessories:
| Qty | Part Name |
|---|---|
| 1 | Winch Power Control Box Bracket |
| 2 | Nut Plate |
| 2 | Connect Bracket |
| 4 | Hex Bolts |
| 10 | Hex Bolts |
| 8 | Hex Bolts |
| 6 | Button Head Socket Cap Bolts Screws |
| 14 | Split Lock Washer |
| 12 | Split Lock Washer |
| 24 | Flat Washer |
| 12 | Flat Washer |
| 14 | Flange Hex Lock Nuts |
| 10 | Hex Nuts |
Tools required:
- A. 19mm Socket Wrench
- B. 18mm Wrench
- C. 13mm Wrench
- D. 5mm HEX Socket Wrench
Installation time:
About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.8200-S), please scan the QR code.
Product Usage Instructions
Installation instruction:
- Step 1: Remove the factory bumper. Ready to install this bumper.
- Step 2: To assemble the wings & the main body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12). Repeat the same installation methods on the other side.
- Step 3: To install the bull bar into the main body. Use the Hex Bolts (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8).
- Step 4: To assemble the winch power control box bracket & the winch bracket. Use the Button Head Socket Cap Bolts Screws (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8). This step isn’t 100% necessary. It depends on whether you have the winch power control box.
- Step 5: Put the nut plate into the vehicle body. To install the winch bracket into the vehicle body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2).
- Step 6: Lift up the bumper and install it into your vehicle. Use the Hex Bolts (M1235), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12).
- Step 7: To connect the bumper and the vehicle with the connect bracket. Use the Button Head Socket Cap Bolts Screws (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8). The upper bolts don’t need to install the flat washer & the split lock washer.
- Step 8: Keep the bolts loose, raise the bumper, adjust the gap between it and the car, and then tighten up all of the bolts after confirming that the desired effect is achieved.
- Step 9: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally do not affect the installation of the product.
- Please feel free to contact your distributor if you have any questions about your purchase.
Frequently Asked Questions
Q: How long does it take to install the front bumper?
A: The installation time is approximately 1.5 hours, but it may vary depending on your mechanical skill level.
Q: Do I need any special tools for installation?
A: Yes, you will need a 19mm Socket Wrench, 18mm Wrench, 13mm Wrench, and 5mm HEX Socket Wrench.
Q: Is the winch power control box bracket necessary for installation?
A: No, it is not necessary. The installation of the winch power control box bracket depends on whether you have the winch power control box.
Q: What should I do if I have missing parts?
A: Please verify all parts are present before starting the installation. If you have missing parts, please contact your distributor for assistance.
Contents
Tools required
- A. 19mm Socket Wrench;
- B. 18mm Wrench;
- C. 13mm Wrench;
- D. 5mm HEX Socket Wrench;
Installation time
About 1.5 hours, 2-3 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.8200-S), please scan the QR code.
Installation instruction:
- Step 1: Remove the factory bumper. Ready to install this bumper.
- Step 2: To assemble the wings & the main body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12). Repeat the same installation methods in the other side.
- Step 3: To install the bull bar into the main body. Use the Hex Bolts (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8).
- Step 4: To assemble the winch power control box bracket & the winch bracket.
Use the Button Head Socket Cap Bolts Screws (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8). This step isn’t 100% necessary. Depends if you have the winch power control box.
- Step 5: Put the nut plate into the vehicle body. To install the winch bracket into the vehicle body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2).
- Step 6: Lift up the bumper and install it into your vehicle. Use the Hex Bolts (M1235), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12).
- Step 7: To connect the bumper and the vehicle with the connect bracket. Use the Button Head Socket Cap Bolts Screws (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8). The upper bolts don’t need install the flat washer & the split lock washer.
- Step 8: Keep the bolts loose, raise the bumper, adjust the gap between it and the car, and then tighten up all of bolts after confirming that the desired effect is achieved.
- Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Attention
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>