WINEGARD FL-5000 FlatWave Antenna Instruction Manual
- June 16, 2024
- WINEGARD
Table of Contents
Model Fl-5000
For help, email help@winegard.com or call
1-800-788-4417.
DO NOT RETURN ANTENNA TO PLACE OF PURCHASE.
Specifications
- For indoor use only
- Range of 25 miles (performance may vary based on terrain and obstructions)
- For high VHF & UHF channels
- Recommended for use with one TV
- Small, compact size
- Includes 3M™ Command™ Brand Strips
- No assembly required
- Model FL-5000
Setup
-
Connect the mini coax cable to the “Antenna In” coax port on the TV.
-
Run a channel scan. (For a listing of likely channels available in your area, go online to www.winegard.com/localchannels.)
-
If not satisfied with the number of channels found, try re-positioning the antenna. Moving the antenna three feet in one direction is often enough to change the reception. Then, re-run a channel scan.
Once the best location has been determined, secure the antenna with the
provided command strips, which can be placed on any part of the antenna.
If more coaxial cable is needed to mount the antenna in the desired location,
connect the coaxial cable to a female-to-female barrel connector (Winegard
model FS-8100), sold separately), and attach additional coaxial cable.
Do not paint the FlatWave antenna. This could block signal and void your
warranty. Note that the antenna is not meant for use in an attic.
Tips for Maximizing reception
Mount the antenna on a window that faces the broadcast tower of stations that you want to receive. The sides of the antenna have blind spots, so the antenna may not “see” enough signal from the broadcast tower if the sides of the antenna face the tower.
If the antenna is mounted so that it hangs vertically, the coax cable should run from the top or bottom of the antenna. If the antenna is mounted so that it lies flat (e.g. on a table), the coax cable should point toward the signal.
The FlatWave antenna is small enough to hide behind a TV or picture frame.
The coax cable is running from the side of the antenna instead of the top or bottom of the antenna. Try re-positioning the antenna so that the coax cable runs from the top or bottom of the antenna, and run a new channel scan.
The antenna may pick up signal when mounted near electronics, or electronics, including the television itself, may reflect the signal from the broadcast tower. If so, try mounting the antenna higher on the wall, and run a new channel scan. The higher the antenna, the better signal you will receive.
Questions & answers
What channels can the FlatWave antenna receive?
The FlatWave antenna can receive programming from all of the major local broadcast networks (e.g. ABC, CBS, FOX, NBC, PBS) plus additional networks (Qubo, ION, The CW, This TV, MyNetworkTV, Azteca, Telefutura, Univision, and Telemundo). The FlatWave antenna can also receive local news, weather and educational programs that satellite and cable don’t offer.
How can I find out what channels are broadcast in my area?
Check out www.winegard.com/localchannels. On this site, you can enter your address and get a listing of likely channels available in your area.
How many channels will I receive with the FlatWave antenna?
The number of channels will vary from location to location. Generally speaking, if you live in or near a metropolitan area you will receive more channels than if you live outside a metropolitan area. Each location is different. Keep in mind that antenna reception may vary based on terrain (including trees, buildings, hills and mountains). The fewer obstructions, the better your chance for receiving strong digital signals.
Do I need to pay for programming?
No—local programming received through an over-the-air antenna is free!
Does the FlatWave antenna work with any TV?
The FlatWave antenna works with any TV or device that has an ATSC tuner. Devices that have built-in ATSC tuners include TVs, laptops, PCs, some satellite receivers, and digital recording devices (DVRs). TIP Any television manufactured after March 1, 2007 is required by U.S. government to have an ATSC tuner. If your TV menu has an option for scanning for digital channels, then your television has an ATSC tuner.
Can I connect the FlatWave antenna to multiple televisions?
No—the FlatWave antenna is designed to connect to connect to a single television. Splitting the signal between multiple TVs will degrade the signal.
How do I set up the FlatWave antenna?
1.) Place the antenna in the desired location. 2.) Connect the coax cable coming from the FlatWave antenna to the “Antenna In” coax port on your TV. 3.) Run a channel scan.
Is there anywhere that the antenna shouldn’t be mounted?
The antenna is designed for indoor use only. The FlatWave antenna is not meant to be mounted outdoors or in the attic.
How do I know where the signal is strongest?
After connecting the coax cable from the FlatWave antenna to the “Antenna In” port on the TV, run a channel scan. Try the antenna in different locations, making sure to run a channel scan every time you move the antenna. Finding TV signal is similar to cell phone coverage. Sometimes walking a few feet can make a difference. The less obstructions and the higher the antenna is mounted, the better chance of receiving a strong signal.
Can I connect the FlatWave antenna to additional coax?
Yes. Connect the provided coax to a female-to-female barrel connector, and then connect additional coax. Winegard recommends model FS-8100 barrel connector (sold separately). Depending on the length of coax cable added, some signal degradation may be experienced.
Troubleshooting
| Issue | Possible Cause |
|---|---|
| I am not getting channels. | Try running a new channel scan on the TV. Try the |
antenna in a new location. Something may be obstructing the signal.
One channel is missing.| Try turning the antenna 10 or 20 degrees in either
direction to avoid reflection or to better optimize the signal, or try moving
the antenna to a new location.
Try running a new channel scan on the TV. Refer to the channel scan insert for
more information.
The picture or sound freezes while I am watching a channel, or there are boxes
in the picture.| This is often caused by a weak or intermittent signal. Try
moving the antenna to a better location or aiming it directly at the tower for
this channel.
Digital television Facts
Your Winegard antenna is digital and HD ready. This means that the antenna
receives all available digital and HD local programming in your area.
The FlatWave antenna works with any TV or device with an ATSC tuner. As more
and more local networks are broadcasting their programs in HD, you can
experience your favorite shows in crisp, clear FREE HD! You also have the
ability to receive programming that cable and satellite companies may not
provide. It doesn’t get any better than that!
Antenna reception may vary based on transmitting antenna tower height, lobe pattern of the transmitter, height of the receiving antenna, weather conditions and terrain on receiving path including trees, buildings, hills, mountains, etc.
90 DAY LIMITED WARRANTY
Winegard Company warrants this Winegard product against any defects in
materials or workmanship within 90 (ninety) days from date of purchase. No
warranty claim will be honored unless at the time the claim is made, you
present proof of purchase to an authorized Winegard dealer (if unknown, please
contact Winegard Company, 3000 Kirkwood Street, Burlington, IA 52601-2000,
Telephone 800-288-8094).
Winegard Company (at its option) will either repair or replace the defective
product at no charge to you. This warranty covers parts, but does not cover
any costs incurred in removal, shipping or reinstallation of the product. This
limited warranty does not apply if the product is damaged, deteriorates,
malfunctions or fails from: misuse, improper installation, abuse, neglect,
accident, tampering, modification of the product as originally manufactured by
Winegard, usage not in accordance with product instructions or acts of nature
such as damage caused by wind, lightning, ice or corrosive environments such
as salt spray and acid rain.
The 90 Day Warranty is provided on the condition that the equipment is
properly delivered with all handling and freight charges prepaid to your
Winegard dealer for return to our factory for repair or replacement. Winegard
dealers will arrange for the replacement or repair and return to you without
charge the product which failed due to defective material or workmanship.
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES,
EXPRESS OR IMPLIED, MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED
TO THE 90-DAY PERIOD OF THIS WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person, whether in
contract, tort or otherwise, and Winegard shall not be liable for incidental
or consequential damage or commercial loss, or from any other loss or damage
except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion of limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601
800-288-8094 • Fax
319-754-0787 •
www.winegard.com
Printed in U.S.A. ©2011 Winegard Company Rev4 7/12 2452248
Winegard and FlatWave are registered trademarks of Winegard Company.
3M and Command are trademarks of 3M Company.
https://manual-hub.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>