JL AUDIO SB-T-4RNRG5 Stealthbox Compatible with 2010-Up Toyota 4Runner Installation Guide

JL AUDIO SB-T-4RNRG5 Stealthbox Compatible with 2010-Up Toyota 4Runner

IMPORTANT

• Installation requires appropriate tools and safety equipment.
• Professional installation is recommended.
• If you prefer to perform your own installation, please read this installation guide completely before beginning.
• Before cutting or drilling, check for potential obstacles behind mounting surfaces.
• Mount this product securely to prevent damage or injury in severe conditions.

INCLUDED HARDWARE

POWER RECOMMENDATION

JL Audio recommends high quality amplifiers such as the JL Audio XD300/1v2. The diagram below shows the recommended crossover settings for the XD300/1v2. For a detailed description of the amplifier settings, consult the owner’s manual for the amplifier. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealth box. JL Audio recommends using a 4 AWG power kit such as the XD-P(S4-1 B for your Stealthbox amplifier. Other kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplifier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-B(S12-25.

• STEP 1
  Clear the rear cargo area.

• STEP 2
  Carefully unclip and remove the center cargo door sill panel.

• STEP 3
  Open the indicated plastic cover and remove the exposed 1 O mm bolt.

• STEP 4
  Turn the cargo net retaining hook clockwise to release and remove the hook. Remove the exposed Phillips screw.

• STEP 5
  Use a panel removal tool to remove the two indicated trim covers. Remove the two exposed 10 mm bolts

• STEP 6
  Open the two indicated plastic covers and remove the two exposed 1 O mm bolts.

• STEP 7
  Remove the lower rear seat carpeted trim panel from the vehkle.
  STEP 8
  Carefully uncllp and remove the carpeted floor panel. There are four (4) cllps that secure the floor panel to the vehicle. Lift and remove the exposed Styrofoam subfloor panel. Remove the single exposed Phillips screw from the location indicated on the floor.

• STEP 9
  Use a panel removal tool to carefully remove the passenger rear seat recline lever assembly. The lever assembly must be pried towards the center of the vehicle to remove.

• STEP 10
  After removing the passenger rear seat recline lever assembly, disconnect the metal pull cable from the back of the handle.

• STEP 11
  Remove the two exposed 10 mm bolts.

• STEP 12
  Open the plastic cover over the seat belt bolt and remove the exposed 14 mm bolt.

• STEP 13
  Flip the carpeted flap at the bottom of the rear seat forward and remove the exposed 14 mm bolt.

• STEP 14
  With the passenger rear seat back upright, remove the indicated 14 mm bolt.

• STEP 15
  From behind the rear passenger seat, remove the indicated 14 mm bolt and move the rear passenger seat back aside.

• STEP 16
  Carefully uncllp and remove the rear passenger side door sill trim panel.

• STEP 17
  Lift the weatherstripping from the rear edge of the OEM rear panel.
  Carefully unclip the OEM rear panel and remove it from the vehicle.

• STEP 18
  From the rear of the OEM rear panel, disconnect the power harnesses from the AC and DC power sockets.
  Remove the OEM rear panel from the vehicle.

• STEP 19
  Use a tool to cut the OEM plastic leg where indicated by the yellow circle in the image.
  Install one of the supplied 1/4 – 20 U-Nuts onto the exposed OEM metal mounting tab.

• STEP 20
  Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over each of six 1/4″ – 20 x 111 Hex Head Screws. Referring to Page 2 as a guide, use two assemblies per Bracket to attach the Top Bracket, Bottom Bracket, and Side Bracket to the Stealthboxt. Center each assembly in the Bracket Slots, then fully tighten them into the Stealthbox threaded inserts. Install one 1/4 – 20 U-Nut onto the Bottom Bracket as indicated.

• STEP 21
  Starting from the bottom of the openlng, insert the Stealthboxc into the mounting location, aligning each Bracket to the OEM metal mounting points.
  The Bottom Bracket sits behind the OEM bottom metal mounting point, whereas the other mounting brackets will sit in front of the remaining OEM metal mounting points.

• STEP 22
  Slide a 1/411 Split Lock Washer and a 1/411 Flat Washer over each of three M6 x 1mm, 25mm Hex Head Screws. Use these assemblies to secure the top hole of the Front Bracket, the Top Bracket, and the Side Bracket to the OEM metal mounting points. Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over one
  1 /4″ – 20 x 3/4″ Hex Head Screw and use it to secure the bottom hole of the Front Bracket to the OEM metal mounting point.

• STEP 23
  Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over each of three 1 /4″ – 2 O x 1″ Hex Head Screws. Use these assemblies to secure the Front Bracket to the threaded holes on the Stealth box and the Bottom Bracket to the OEM metal mounting point.
  Route the speaker cable and connect to the terminal cup on the Stealthboxc .

• STEP 24
  Flip the OEM rear panel over and lay it on a flat surface. Use a screwdriver to remove the 15 Phillips screws around the perimeter of the cargo pocket. Remove the cargo pocket from the panel. After removing the cargo pocket, use a screwdriver to remove the two indicated Phillips screws, then remove the indicated trim piece from the rear of the pane

• STEP25
  Remove the plastic protrusions from the back of the OEM rear panel within the indicated areas.
  (Note: The plastic protrusions have already been removed in this image.)

• STEP 26
  Place the Stealthbox<ll Grille Panel over the panel opening with the grille cloth facing down. Use a screwdriver to hand tighten 14 of the Phillips screws removed in STEP 20 around the Grille Panel’s perimeter.
  After hand tightening the screws, work back around the perimeter of the Grille Panel and fully tighten each screw. Do not overtighten the screws.

• STEP 27
  Reinstall the OEM rear panel.

• STEP 28
  Reinstall the remainder of the OEM panels and parts.

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox

MID/HIGH-FREQUENCY DRIVER FITMENT

A variety of JL Audre coaxial and component systems wrll fit in the factory speaker locations of you vehicle.

954-443-1100
www.jlaudio.com
All specifications are subject to change without notice “L Audio” and “How we play”a registered trademarks of lL Audio, he. Ahead of the Curve” and Its respective logo are trademarks of JL Audio, hc
Printed in U5A 2021 JLAudio, he For more detailed information please visit us online at wwwjlaudio.com

USA Limited Warranty

FOR CAR AUDIO PRODUCTS SOLD AT RETAIL:
JL Audio warrants these products to be free of defects in materials and workmanship from the original date of purchase for these periods: One (1) year from the original date of purchase: Car Speakers and Subwoofers Two (2} years from the original date of purchase: Car Amplifiers, Electronics, Enclosed Subwoofers, Stealthbox and Connection Products
Note: The Car Amplifier Warranty Period Is extended to three (3) years when accompanied by the purchase of a qualifying JL Audio Amplifier Power Connection System and with installation by an authorized JL Audio dealer.
This warranty is not transferable and applies only to the original retail purchaser from an authorized JL Audio dealer in the USA. Should service be necessary under this warranty for any reason due to manufacturing defects or malfunction, on, JL Audio will (at Its discretion), repair or replace the defective product with the new or remanufactured product at no charge.

Note: Products purchased from unauthorized dealers are not covered under warranty.
Damage caused by the following is not covered under warranty: accident, misuse, physical abuse, product modification or neglect, failure to follow Installation instructions, unauthorized repair attempts, and misrepresentations by the seller. Loudspeakers with thermal or over-excursion damage are not covered under warranty. This warranty does not cover incidental, accidental or consequential damages and does not cover the cost of removing or reinstalling products. Cosmetic damage due to improper hand I mg, accident or normal wear and tear or exposure to harsh chemicals Is not covered under warranty. JL Audio will not be responsible for restoring or maintaining custom finishes or cosmetic treatments applied to products.
This warranty is void If the product’s serial number has been removed, altered or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If you need service on your JL Audio product:
All USA retail warranty returns should be sent to JL Audio freight prepaid through an authorized JL Audio dealer and must be accompanied by proof of purchase (a copy of the original retail sales receipt.) Direct returns from consumers or non-authorized dealers will be refused unless spe<ifically authorized by JL Audio with a valid return authorization number Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is prior to purchasing date. Return only defective components. (If one speaker falls In a system, return only that speaker component, not the entire system.) Non-defective items received will be returned freight-collect. The customer is responsible for shipping charges and Insurance in sending the product to JL Audio. Freight damage on returns is not covered under warranty.

JL Audio Customer Service:
1-954-443-1100 9:00 AM – 5:00 PM (Eastern Time Zone)

JL Audio Technical Support:
www.jlaudio.com/support

Original Equipment Warranty

For Jl Audio products installed as original equipment by a boat or vehicle manufacturer, warranty coverage Is provided within the boat or vehicle manufacturer’s warranty program. Please contact your boat dealer or manufacturer.

International Warranty

JL Audio Car Audio products are warrantied against defects in materials and workmanship for a minimum time period as stated In the USA warranty above, beginning on the date of purchase from a Dealer authorized by a Jl Audio Distributor. The warranty is only valid within the country of purchase and products are covered by each country’s JL Audio Distributor warranty program. To find your country’s Distributor please visit this link: www.jlaudlo.com/pages/dealer-locator Consumers In the £EA countries and the Russian Federation are protected by local consumer law and benefit from local statutory warranties. Jl Audio reserves the right to change or modify any of the terms and conditions contained in this Warranty Statement, at any time and in our sole discretion. Any changes or modification will be effective immediately upon posting of the revisions on the JL Audio website at www.jlaudio.com/warranty, and you waive any right you may have to receive specific notice of such changes or modifications.

References

• JtAudio.com is for sale | HugeDomains

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>