JL AUDIO 94685 Stealthbox For 2010-Up Toyota 4Runner Installation Guide
- June 4, 2024
- JL AUDIO
Table of Contents
INSTALLATION GUIDE for the
SB-T-4RNRGS/10TWS3 SKU# 94685
2010 & Up Toyota 4Runner
Enclosure Type: Sealed
Driver Type: (0″‘3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 409 votes (AIMS method!
SB-T-4RNRGS/1OTW3_ INSTR_SKU# 011555
! IMPORTANT
- Installation requires appropriate tools and safety equipment. Professional installation is recommended.
- If you prefer to perform your own installation, please read this installation guide completely before beginning.
- Before cutting or drilling, check for potential obstacles behind mounting surfaces.
- Mount this product securely to prevent damage or injury in severe conditions.
| 
---|---
INCLUDED HARDWARE
| BOX ID | • | SKU | Description |
|---|---|---|---|
| 1 | 3 | 154188 | M6 x 1 mm, 25 mm Hex Head Screw |
| 2 | 13 | 150066 | 1/4″ Split Lock Washer |
| 3 | 13 | 150068 | 1/4″ Flat Washer |
| 4 | 1 | 154190 | Front Bracket |
| 5 | 2 | 152191 | Top/Bottom Bracket |
| 6 | 9 | 151137 | 1/4″ – 20 x 1″ Hex Head Screw |
| 7 | 1 | 154189 | 1/4″ – 20 x 3/4″ Hex Head Screw |
| 8 | 2 | 151164 | 1/4 – 20 U-Nut |
| 9 | 1 | 154192 | Side Bracket |
| 10 | 1 | 154187 | Grille Panel (not shown) |
POWER RECOMMENDATION
JL Audio recommends high-quality amplifiers such as the JL Audio XD300/1v2.
The diagram below shows the recommended crossover settings for the XD300/1v2.
For a detailed description of the amplifier settings, consult the owner’s
manual for the amplifier. If another amplifier is being used, please reference
this illustration and use similar settings on that amplifier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PC54-1B for your Stealthbox® amplifier. Other kits are available should you be using more than one amplifier. Signal wires such as the JL Audio Premium Audio Interconnect Cables should be used to provide a signal for both channels of the amplifier. JL Audio recommends using 12 AWG speaker wires for subwoofers such as our XC-BCS12-25.
| STEP 1 Clear the rear cargo area.
---|---
STEP 2 Carefully unclip and remove the center cargo door sill panel.
STEP 3 Open the indicated plastic cover and remove the exposed 10 mm bolt.
STEP 4 Turn the cargo net retaining hook clockwise to release and remove the
hook. Remove the exposed Phillips screw.
| STEP5 Use a panel removal
tool to remove the two indicated trim covers, Remove the two exposed 10 mm
bolts.
---|---
STEP 6 Open the two indicated plastic covers and remove the two exposed 10 mm
bolts.
STEP 7 Remove the lower rear seat carpeted trim panel from the vehicle.
STEP 8 Carefully unclip and remove the carpeted floor panel. There are four
(4) clips that secure the floor panel to the vehicle. Lift and remove the
exposed Styrofoam subfloor panel. Remove the single exposed Phillips screw
from the location indicated on the floor.
| STEP 9 Use a panel removal
tool to carefully remove the passenger rear seat recline lever assembly. The
lever assembly must be pried towards the center of the vehicle to remove.
---|---
STEP 10 After removing the passenger rear seat recline lever assembly,
disconnect the metal pull cable from the back of the handle.
STEP 11 Remove the two exposed 10 mm bolts.
STEP 12 Open the plastic cover over the seat belt bolt and remove the exposed
14 mm bolt.
| STEP 13 Flip the carpeted flap at the bottom of the rear seat forward and
remove the exposed 14 mm bolt.
---|---
STEP 14 With the passenger rear seat back upright, remove the indicated 14 mm
bolt.
STEP 15 From behind the rear passenger seat, remove the indicated 14 mm bolt
and move the rear passenger seat back aside.
STEP 16 Carefully unclip and remove the rear passenger side door sill trim
panel.
| STEP 17 Lift the
weatherstripping from the rear edge of the OEM rear panel. Carefully unclip
the OEM rear panel and remove it from the vehicle.
---|---
STEP 18 From the rear of the OEM rear panel, disconnect the power harnesses
from the AC and DC power sockets.
Remove the OEM rear panel from the vehicle.
STEP 19 Use a tool to cut the OEM plastic leg were indicated by the yellow
circle in the image. Install one of the supplied 1/4 – 20 U-Nuts onto the
exposed OEM metal mounting tab.
STEP 20
Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over each of six 1/4″ –
20 x 1″ Hex Head Screws. Referring to Page 2 as a guide, use two assemblies
per Bracket to attach the Top Bracket, Bottom Bracket, and Side Bracket to the
Stealthbo•. Center each assembly in the Bracket Slots, then fully tighten them
into the Stealthbox threaded inserts. Install one 1/4-20 U-Nut onto the Bottom
Bracket as indicated.
| STEP 21
Starting from the bottom of the opening, insert the Stealthbox° into the
mounting location, aligning each Bracket to the OEM metal mounting points.
The Bottom Bracket sits behind the OEM bottom metal mounting point, whereas
the other mounting brackets will sit in front of the remaining OEM metal
mounting points.
---|---
STEP 22
Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over each of three M6 x
1mm, 25mm Hex Head Screws. Use these assemblies to secure the top hole of the
Front Bracket, the Top Bracket, and the Side Bracket to the OEM metal mounting
points. Slide a 1/4″ Split Lock Washer and a 1/4″ Flat Washer over one 1/4″ –
20 x 3/4″ Hex Head Screw and use it to secure the bottom hole of the Front
Bracket to the OEM metal mounting point.
STEP 23 Slide a 1/4″ Split Lock Washer and a 1/4′ Flat Washer over each of
three 1/4″ – 20 x 1″ Hex Head Screws. Use these assemblies to secure the Front
Bracket to the threaded holes on the Stealthbox and the Bottom Bracket to the
OEM metal mounting point.
Route the speaker cable and connect to the terminal cup on the Stealthbox’.
STEP 24 Flip the OEM rear panel over and lay it on a flat surface. Use a
screwdriver to remove the 15 Phillips screws around the perimeter of the cargo
pocket. Remove the cargo pocket from the panel.
After removing the cargo pocket, use a screwdriver to remove the two indicated
Phillips screws, then remove the indicated trim piece from the rear of the
panel.
| STEP 25 Remove the plastic protrusions from the back of the OEM rear panel
within the indicated areas.
(Note: The plastic protrusions have already been removed in this image.)
---|---
STEP 26 Place the Stealthbox Grille Panel over the panel opening with the
grille cloth facing down. Use a screwdriver to hand tighten 14 of the Phillips
screws removed in STEP 20 around the Grille Panel’s perimeter.
After hand tightening the screws, work back around the perimeter of the Grille
Panel and fully tighten each screw. Do not overtighten the screws.
| STEP 27
Reinstall the OEM rear panel.
---|---
STEP 28
Reinstall the remainder of the OEM panels and parts.
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox’!
MID/HIGH-FREQUENCY DRIVER FITMENT
A variety of 11_ Audio coaxial and component systems will fit in the factory
speaker location of your vehicle.
| Location / OEM Speaker Size | Suggested JL Audio Speaker Models |
|---|---|
| Coaxial Models | Component Models |
| Front Doors / 6 x 9-inch | C1-690in, C1-690tx0, C2-690tx°0 C2-650×0), |
| C5-650×0) | C1-6901, C1-6500), C2-6500, C3-650), C5-6500), C7-650cw0+2) |
| Rear Doors / 6.5-inch | CI.650x, C2-650x, C5.650x |
C5-650, C7-650cw0)
1 – Installation may require an adaptor, 2 – Component woofer only
(954) 443- 1 1 00
www.jlaudlo.com
NI spedlIcadais are subject to chins without notice IL Audio” end ‘How we
Eerste registered trademarks of A.
ALS Ix “head of the Curve and Its respect.* logo Be tradonalts of Aissio, he
PANS In the USA
• 02021 A.Aucio, hc • ice emcee &Wed Information Oat Altus oriels et
twerkjbudlo.com.
JLA-SKU# 011489 •
ver. 10.12.2021 • 10369
NORTH COMMERCE PARKWAY
• MIRAMAR, FLORIDA • 33025 • USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>