JL AUDIO 94748 Car Stealthbox Installation Guide

: June 1, 2024
: JL AUDIO

Table of Contents

JL AUDIO 94748 Car Stealthbox
Product Information
Product Usage Instructions
FAQ
IMPORTANT
INCLUDED HARDWARE
Installation Instructions
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JL AUDIO 94748 Car Stealthbox

Product Information

Specifications

Enclosure Type: Sealed
Driver Type: 10TW1
Nominal Impedance: 2 ohms
Continuous Power Handling: 300 watts (RMS method)

Product Usage Instructions

Empty the rear seat area.
Lift the rear seat and empty the storage pocket. Carefully remove the C-pillar cover on both sides of the vehicle.
Carefully unclip and remove the rear door sill panels on both sides of the vehicle.
Remove the T-50 Torx bolt from seat belt bracket under the seat on the passenger side, and disconnect the harness.
Pull the seat belt bracket through to the top of the seat cushion.
Push the seat belt buckles below the seat cushion.
Remove two 15mm bolts from the seat bracket on both sides of the vehicle.
Press the release tab and lift to remove each of the rear seat headrests.
Pull the release strap to release the seat back.
Carefully remove the rear seat from the vehicle.
Remove the passenger-side storage pocket.
Remove the driver’s side storage pocket.
Place the driver-side storage pocket face down, and locate the indicated marker.
Using a 1/8 drill bit, carefully drill through the centre of the marker on the storage pocket.
Using a 5/16 drill bit, enlarge the hole drilled in the previous step.
Peel the adhesive backing and place Foam Tape strips into the driver side storage pocket, as needed.
Route the speaker cable as necessary and place the enclosure into the storage pocket.
Apply Vibra-Tite 132 to an M6 x 14mm Flanged Hex Head Screw, pass it through a drilled hole in the bottom of the storage pocket, into the threaded insert in the enclosure, and fully tighten.
Peel the adhesive backing and place Foam Tape strips onto the vehicle floor, as needed.
With the enclosure installed in the driver-side storage pocket, reinstall the pocket.
Reinstall the passenger side storage pocket, the rear seats, headrests, seat belt brackets, and trim panels.

FAQ

Q: What is the estimated time for installation?
A: The estimated time for installation is 2 hours.
Q: What is included in the hardware?
A: The included hardware consists of M6 x 14mm Flanged Hex Head Screw, Vibra-tite 132 (not shown), and Foam Tape Strips (not shown).

IMPORTANT

Installation requires appropriate tools and safety equipment.
Professional installation is recommended.
If you prefer to perform your own installation, please read this installation guide completely before beginning.
Before cutting or drilling, check for potential obstacles behind mounting surfaces.
Mount this product securely to prevent damage or injury in severe conditions.

JL-AUDIO-94748-Car-Stealthbox-FIG-1

INCLUDED HARDWARE

BOM ID	Qty	SKU	Description
1	1	155078	M6 x 14mm Flanged Hex Head Screw
–	1	194157	Vibra-Tite 132 (not shown)
–	1	150249	Foam Tape Strips (not shown)

JL-AUDIO-94748-Car-Stealthbox-FIG-2

Installation Instructions

STEP 1
Empty the rear seat area.

STEP 2
Lift the rear seat and empty the storage pocket. Carefully remove the C-pillar cover on both sides of the vehicle.

STEP 3
Carefully unclip and remove the rear door sill panels on both sides of the vehicle.

STEP 4
Remove the T-50 Torx bolt from the seat belt bracket under the seat on the passenger side, and disconnect the harness.

STEP 5
Pull the seat belt bracket through to the top of the seat cushion.

STEP 6
Push the seat belt buckles below the seat cushion.

STEP 7
Remove two 15mm bolts from the seat bracket on both sides of the vehicle.

STEP 8
Press the release tab and lift the to remove each of the rear seat headrests.

STEP 9
Pull the release strap to release the seat back.

STEP 10
Carefully remove the rear seat from the vehicle.

STEP 11
Remove the passenger-side storage pocket.

STEP 12
Remove the driver’s side storage pocket.

STEP 13
Place the driver-side storage pocket face down, and locate the indicated marker.

STEP 14
Using a 1/8” drill bit, carefully drill through the centre of the marker on the storage pocket.

STEP 15
Using a 5/16” drill bit, enlarge the hole drilled in the previous step.

STEP 16
Peel the adhesive backing and place Foam Tape strips into the driver-side storage pocket, as needed.

STEP 17
Route the speaker cable as necessary and place the enclosure into the storage pocket.
Apply Vibra-Tite 132 to an M6 x 14mm Flanged Hex Head Screw, pass it through the drilled hole in the bottom of the storage pocket, into the threaded insert in the enclosure, and fully tighen.

STEP 18
Peel the adhesive backing and place Foam Tape strips onto the vehicle floor, as needed.

STEP 19
With the enclosure installed in the driver-side storage pocket, reinstall the pocket.

STEP 20
Reinstall the passenger side storage pocket, the rear seats, headrests, seat belt brackets and trim panels.

CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!

JL-AUDIO-94748-Car-Stealthbox-FIG-23

MID/HIGH-FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle.

Location / OEM Speaker Size| Suggested JL Audio Speaker Models
---|---
Coaxial Models| Component Models
Front| Door / 6.5-inch| C1-650x, C2-650x| C1-650, C2-650, C3-650,

C6-650cw(2), C7-650cw(2)

Rear| Pillar / 4-inch| C1-400x, C2-400x| C7-350cm(1)

Installation may require an adaptor,
Component woofer only

How we play.

Please review the warranty information included with each product for details. Warranty is valid only if the product was purchased from an Authorized JL Audio Dealer. Authorized dealer status can be verified with the Dealer Locator on www.jlaudio.com. International Warranty: Please contact your country’s JL Audio distributor for specific warranty details. © Garmin Ltd. or its subsidiaries. All rights reserved. Garmin, JL Audio, Stealthbox, and How We Play. are trademarks of Garmin Ltd. or its subsidiaries and are registered in one or more countries, including the U.S. The JL Audio logo, the How We Play logo, the Stealthbox logo, and the SBX logo are trademarks of Garmin Ltd. or its subsidiaries. Product images shown are for illustrative purposes only and may differ from the actual product. Due to continuous product development, all specifications are subject to change without notice.