JL AUDIO MBT-RXv2 Weatherproof Receiver Instruction Manual
- May 15, 2024
- JL AUDIO
Table of Contents
MBT-RX v2
Weatherproof Receiver with
Bluetooth® Wireless Technology
MBT-RXv2 Weatherproof Receiver
Installation Considerations
- Installation requires appropriate tools and safety equipment. Professional installation is recommended.
- This product is water-resistant. Do not submerge or subject to high-pressure water spray.
- Do not mount in areas of extreme heat.
- Mount this product securely to prevent damage or injury in severe conditions.
- Before cutting or drilling, check for potential obstacles behind mounting surfaces.
- Carefully route all system wiring away moving parts and sharp edges; secure all wiring and use grommets and loom where appropriate to protect from sharp edges.
Pairing Considerations
Multiple devices can be paired to the MBT-RXv2, but only one streaming device can connect at a time. The MBT-RXv2 will remember the last device that was connected to it and reconnect with it automatically. If that streaming device is not active, then other paired streaming devices can connect manually, or new streaming devices can be paired. When a connected streaming device is out of range for more than one minute, the MBT-RXv2 will automatically disconnect the streaming device and return to pairing mode (internal LED will flash). When that same device comes back into range, it should be reconnected to the MBT-RXv2 manually.
Pairing Your Device
- Ensure your streaming device has Bluetooth® enabled and that the MBT-RXv2 is on. The internal LED will flash to indicate pairing mode is active.
- Select “MBT-RXv2” from your device’s Bluetooth® setup menu.
- When successfully connected, the internal LED will illuminate solid.
- Once connected, all playback controls are managed using the connected streaming device.
Specifications|
---|---
Bluetooth® Profile| A2DP (High-Quality, Stereo Audio)
Bluetooth® Core Spec| Version 5.0 with Qualcomm® aptX-HD
Connection Range| Up to 35 ft /11 m
Frequency Response| 20 Hz -20 kHz (±1 dB)
Operating Voltage| 10 – 16VDC
Current Draw / Fuse Value| 40 mA /2 A
Remote Output Capacity| 1 A
S/N Ratio| 100 dB (20 Hz -20 kHz)
Audio Outputs| One stereo pair of RCA plugs
Output Voltage| 4V RMS
Product Model: MBT-RXv2 PMN: Bluetooth Audio Receiver
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement in
portable exposure condition without restriction.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment.
The device has been evaluated to meet general RF exposure requirement. This
equipment should be installed and operated with minimum distance 0mm between
the radiator & your body.
MBT-RXv2_010524
Printed in China • © 2024 • JL Audio is a trademark of Garmin Ltd. or its
subsidiaries
and is registered in one or more countries, including the U.S. The JL Audio
logo,
MBT-RX logo, and the IPX7 logo are trademarks of Garmin Ltd. or its
subsidiaries.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>