Dong Guan SW570 Wireless Controller User Manual
- June 16, 2024
- Dong Guan
Table of Contents
Dong Guan SW570 Wireless Controller User Manual
Product Overview
- key
- L key
- colorful lights
- Left joystick L3 button
- cross key
- screenshot key
- HOME button
- + key
- R key
- A, B, X, Y keys
- Right joystick R3 button
- indicator light
- ZR key
- M2 key
- TURBO button
- ZL key
- M1 key
- Reset button
Product Brief
- Support Switch/Switch LITE /PC/IOS/Android/Steam platform ;
- Double vibration support;
- With Six-Axis Sensor Function;
- Supports programmable buttons ;
- USB charging cable: 1.2 meters
- Built-in battery capacity： 600mah
- With Breathing LED light
Operation guide
Mode and connection instructions
Switch mode connection: long press the Home button for 3-5 seconds, the LED
running flashes quickly to enter the Bluetooth search mode, and the channel
indicator corresponding to the successful connection is always on. Note: After
the controller enters the synchronization mode, if the synchronization is not
successful within 2.5 minutes, it will automatically sleep.
-
Enter the controller setting page according to the following orders.
-
Enter the page to switch the controller mode.
-
Open the controller according to instruction of (initial use) and enter the connection state. It will be normally operated after successful connection.
Android Gamepad mode connection:
long press HOME+X for 3-5 seconds, LED1 flashes quickly, enters the Bluetooth
search mode, LED1 is always on after the connection is successful, (supports
standard HID mode, it can play Android mobile game hall games, such as:
chicken simulation device, etc.)
IOS 13 mode connection:
Long press HOME+A for 3-5 seconds, LED2+LED3 flashes quickly, enters the
Bluetooth search mode, LED2+LED3 is always on after the connection is
successful, and supports MFI games.
PC Bluetooth mode connection:
long press HOME+X for 3-5 seconds, LED1 flashes quickly, enters the Bluetooth
search mode, and LED1 is always on after the connection is successful (Note:
Bluetooth mode is used to connect to the computer using Android mode, only the
key value setting is recommended experienced players.)
Connect back and wake up
Reconnection:
The controller is in sleep state, short press (A.B.X.Y.+.-.O.↑/↓/←/→) any
button LED1-LED4 flashes, and automatically connects back to the console.
Wake up:
When the console is in sleep state, short press the HOME button of the
controller and the LED1-LED4 will flash to wake up the console， and the
controller will automatically connect to the console.
Sleep and disconnect
The console screen is turned off, and the controller automatically sleeps. It
will automatically sleep if no key is pressed within 5 minutes (including the
sensor does not move). In the state of wireless connection, press the HOME
button for 5 seconds to disconnect from the console.
Charging indication
When the controller is turned off, LED1-LED4 flashes slowly when charging, and
the LED is off when fully charged; Charging in the connected state, the
current channel indicator flashes (slow flashing), and the current indicator
is always on when fully charged; When pairing, reconnecting, charging or low
power, the pairing, reconnecting LED indication is given priority.
Low voltage alarm
When the battery voltage is lower than 3.55V±0.1V, the current channel light
flashes quickly to indicate low voltage; When the battery voltage is lower
than 3.45V±0.1V, it will automatically sleep; Low voltage alarm: the current
indicator light flashes (fast flash)
Turbo function
a: Manual burst setting:
(for the first time) press (A/B/X/Y/L/ZL/R/ZR) one or more action keys, and
then press the TURBO button to start the manual burst function;
b :Automatic burst setting:
(for the second time) press the action button that has turned on the manual
burst function again, and then press the TURBO button to turn on the automatic
burst function;
c :Clear the burst setting:
(for the third time) press the action button that has turned on the automatic
burst function again, and then press the TURBO button to clear the burst
function;
TURBO speed adjustment:
T key and cross key up (UP) is to speed up; T key and cross key down (DOWN) is
to slow down the speed; the speed is divided into 8HZ, 12HZ, 15HZ; the default
is 12HZ. Set TURBO, no after shutdown Memory function, restore the default
12HZ.
Wired connection
PC connection:
Please use a USB cable to connect the controller to the computer, and the
controller LED3 will always be on after connection. (Note: The controller
defaults to X-INPUT mode on the PC side)
Switch connection:
Please use the USB cable to connect the controller to the SWITCH console, and
the corresponding LED light on the controller will always be on after
connection.
Ps3 connection:
Please use the USB cable to connect the controller to the PS3 console, and the
corresponding LED light on the controller will always be on after connection.
RGB colorful lights
a. Rainbow light mode:
The joystick lights on the left and right sides change randomly and gradually
in different colors, and the left and right sides display inconsistently.
(This mode is the default when booting)
b. Monochromatic light mode: (red-orange-yellow-green-cyan-bluepurple) single color is always on, press T + cross key to switch to the next color.
c. Monochrome gradient transformation mode: (red-orange-yellowgreen- cyan-blue-purple repeated cycle change)
a. Press T+Cross key to switch the large lighting mode.
b. Brightness adjustment mode: In non-off mode, long press the T key (press and hold for 2 seconds to start changing), and slowly press the gear to change the brightness from dark to bright in the current mode (0%-25%-50%-75%-100 %) (cycle) let go to set the current brightness (vibration reminder), the default brightness is 75%.
c. Off mode: Double-click the T key to turn off the light (when the light brightness is adjusted to 0%, double-click to turn on the light, you must double-click to turn on and turn off the light when the light brightness is above 25%)
d. After shutting down, the light has a memory function, which can remember the mode and brightness set before shutting down.
Adjustment of motor vibration speed (only available for SWITCH)
In the connected state, press and hold the four keys L, R, ZL, and ZR at the
same time to adjust the motor strength (the handle will vibrate once after
adjusting); the motor vibration is divided into three levels: strong, medium
and weak. Medium, then strong, weak in such a way to cycle.
M key function programming
M key=M1.M2; Programmable keys ↑/↓/←/→/A/B/X/Y/L/R/ZL/ZR/L3/R3;
Programming mode:
-
By default, M1 is mapped to ZL, and M2 is mapped to ZR;
-
Setting method:
press and hold the M key, then press the “+” key, the indicator light flashes and then release it to enter programming, and then press one or several keys you want to set (↑/↓/←/→ /A/B/X/Y/L/R/ZL/ ZR/L3/R3), and then press M to save the setting.
For example:
Press and hold the M1 key, then press the “+” key to enter the programming setting (the indicator light flashes), then press the A key, and then press the M1 key to save the setting. At this time, the M1 key corresponds to the A key function. -
Press and hold the M1 key, M2 key, and – key at the same time, and the indicators of the three keys will flash for 3 seconds to clear the programming. M1, M2 restore the original M1 mapping ZL, M2 mapping ZR
Note:
When entering programming, if you do not press the button that can be
programmed, the original set function will be cleared.
Handle hardware reset
When the handle is abnormal, press the reset button to reset the handle
hardware.
Parameters
Working voltage: DC 3.7V
Working current: 25mA-150mA
Sleep current: ≦27uA
Built-in lithium battery: 600mAh
Input charging voltage: Type-C input 5V
Charging current: ≈350mA
Bluetooth version: 2.1+EDR
Transmission distance: 10 M
Port: TYPE C interface
Battery life: play 10H
FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hamful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause hamful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF waming statement: the device has been evaluated to meet general RF
exposure requirement,
The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>