LUTRON P-BDG-PKG1W Smart Hub Pico Remote Control and In Wall Dimmer User Guide
- June 16, 2024
- Lutron
Table of Contents
- LUTRON P-BDG-PKG1W Smart Hub Pico Remote Control and In Wall Dimmer
- Specifications
- Product Usage Instructions
- FAQ
- Double your warranty
- Contents supplied
- Tools you’ll need
- Installing your dimmer
- Using your Caséta by Lutron kit
- Using your controls
- Troubleshooting
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LUTRON P-BDG-PKG1W Smart Hub Pico Remote Control and In Wall Dimmer
Specifications
- Product: Lutron smart hub, Pico remote control & in-wall dimmer
- Model Numbers: P-BDG-PKG1W, P-BDG-PKG1W-R3, P-BDGPRO-PKG1W
- Power Supply: T-5DC-USB
- Compatible Bulb Types: LED (up to 150 W), Halogen (up to 600 W), Incandescent (up to 600 W)
Product Usage Instructions
Installation for lights with one wall switch (single-pole)
- Turn off power at the circuit breaker before starting the installation.
- Remove the existing switch from the wall.
- If necessary, remove side sections from the dimmer. Do not remove outside side sections on dimmers at the end of the gang.
- Disconnect all three wires from the switch.
- Connect the bare copper (or green) ground wire from the wallbox to the green wire on the dimmer using a wire connector.
- Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
- Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
- Mount the dimmer using the provided screws.
- Attach the wallplate to the dimmer using the provided screws and snap it on.
- Turn on power at the circuit breaker.
- To install the second dimmer, repeat steps 1 through 10.
Important Notes
Some lights have one wall switch (single-pole), while others have two or more wall switches (3-way). If your light has more than one switch, please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.
Removing side sections from the dimmer reduces its maximum wattage rating. Refer to the chart below for maximum wattage information:
Side Sections Removed | LED | Incandescent & Halogen |
---|---|---|
None | 150 W or 600 W* | 150 W or 500 W* |
1 side | 150 W | 400 W |
2 sides | 150 W | 400 W |
- For maximum wattage information when mixing light bulb types, visit www.casetawireless.com/ganging
Tools you’ll need
- Flat-head screwdriver
- Pliers
- Phillips-head screwdriver
FAQ
Q: What light bulb types are compatible with the dimmer?
A: The dimmer is compatible with LED bulbs (up to 150 W), Halogen bulbs (up to 600 W), and Incandescent bulbs (up to 600 W).
Q: My dimmable LED bulbs flicker or turn off, what should I do?
A: If you’re using dimmable LED bulbs and experiencing flickering or turning off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for the best bulb performance.
Lutron smart hub, Pico remote control & in-wall dimmer
Welcome—and thank you for purchasing a Caséta by Lutron dimming kit.
Before you install the dimmer, please watch the installation video at www.casetawireless.com/support
We hope you enjoy the convenience of Caséta by Lutron!
Double your warranty
Love Caséta dimmers? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register
P-BDG-PKG1W
P-BDG-PKG1W-R3
P-BDGPRO-PKG1W
Contents supplied
Tools you’ll need
Works with energy efficient dimmable light bulbs:
- NOTE: You can mix and match dimmable LED, halogen, and incandescent light bulbs with Caséta dimmers.
- Dimmable LED light bulbs vary in their dimming performance. If you’re using these bulbs and theyflicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.
- For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Installing your dimmer
Installation for lights with one wall switch (single-pole)
Turn power off at circuit breaker!
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off power at circuit breaker or
fuse before installing.
Important note (3-Way):
Some lights have one wall switch, while others have two or more wall switches
(such as stair lights, which have a switch at both the top and bottom of the
stairs). We’ve included instructions for lights with one wall switch (called a
single-pole). If your light has more than one switch (called a 3-way), please
visit www.casetawireless.com/3way for
complete installation instructions and how-to videos.
Remove existing switch from wall
- Remove the wallplate from switch.
- Remove the switch and pull it away from the wall.
- Disconnect all three wires* from the switch.
- If your switch has more than 3 wires attached, see “Installing Caséta in a 3-way switch application” video at www.casetawireless.com/3way
Remove side sections (if necessary)
Important note:
Removing side sections reduces the dimmer’s maximum wattage rating. See the
chart below for maximum wattage information.
*Maximum wattage derating chart (120 V~ 50 60 Hz)**
For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging
Connect the dimmer
- Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using a wire connector.
- Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
- Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
Mount the dimmer
Use the screws provided.
Attach the wallplate
Attach the adapter to the dimmer using the screws provided and snap on the wallplate.
(If you installed the dimmer next to other dimmers or switches, you’ll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)
Turn power on at circuit breaker
Repeat Steps 1 through 7 to install the second dimmer.
Using your Caséta by Lutron kit
Install the Lutton smart hub
- A. Connect the smart hub to your Wi-Fi router using the Ethernet cable
- B. Connect the power cord to the smart hub and plug it into an outlet.
Download the Lutron app and walk through setup
Using your controls
Device Ratings
In-wall dimmer
PD-6WCL
120 V~ 50/60 Hz
Lutron smart hub *
L-BDG2 or L-BDGPRO2
5 V- 300 mA
PicoR remote control
PJ2-3BRL
3 V- 10 mA
(1) CR2032 battery
(included)
Power supply
T-5DC-USB
Input : 100–240 V~
50/60 Hz 100 mA
Output : 5 V- 550 mA
Connect to a Class 2, LPS, or SELV, limited energy (<15 W) power source only.
Troubleshooting
Important notes:
- For indoor use only
- Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C)
Go to www.casetawireless.com/support for additional troubleshooting suggestions.
CAUTION
Use only with permanently installed fixtures with dimmable LED, halogen, or
incandescent lamps.
To avoid overheating and possible damage to other equipment, do not use to
control receptacles, motor-driven appliances, or transformer-supplied
appliances.
CAUTION: Risk of Fire, Explosion, Leakage, and Burns. Do Not Recharge, Disassemble, Heat Above 212 °F (100 °C) or Incinerate. This product contains a lithium button/coin cell battery. Keep batteries away from children. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep the batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. The battery in this device contains Perchlorate Material — special handling may apply.
For more information, visitwww.dtsc.ca.gov/hazardouswaste/perchlorate
Codes
Install in accordance with all national and local electrical codes.
Grounding
When no “grounding means” exist in wallbox, the National Electrical Code
(NEC®) allows a control to be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the
circuit is protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or remove green wire
before screwing control into wallbox.
Use of the HomeKit logo means that an electronic accessory has been designed
to connect specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with iPod,
iPhone, or iPad may affect wireless performance.
FCC/IC Information
For FCC/IC information, please visit: www.lutron.com/fcc-
ic
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
The Lutron logo, Lutron, Claro, Caséta, FASS, the Lutron Caséta & RA2 Select
app logo, the design of the Pico remote, and Pico are trademarks or registered
trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
Apple, iPod, iPhone, and iPad are trademarks of Apple Inc., registered in the
U.S. and other countries. HomeKit is a trademark of Apple Inc. App Store is a
service mark of Apple Inc., registered in the U.S. and other countries. All
other product names, logos, and brands are property of their respective
owners.
© 2015-2023 Lutron Electronics Co., Inc.
References
- casetawireless.com/register
- Caseta by Lutron | Smart Light Switches, Controls & Dimmers
- Installing Caséta for a light with two switches | Lutron
- Lutron Support Center | Lutron
- Capacity Derating Charts
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
- dtsc.ca.gov/hazardouswaste/perchlorate
- lutron.com/fcc-ic