LUTRON PD-6WCL Caséta Dimmer Pico User Guide
- June 16, 2024
- Lutron
Table of Contents
LUTRON PD-6WCL Caséta Dimmer Pico
Product Information
Specifications:
- Model: P-DIM-3WAY-WH-C
- Contents:
- In-wall dimmer (PD-6WCL)
- Claro wallplate (CW-1)
- Pico remote control (PJ2-3BRL)
- Pico wallplate bracket (PICO-WBX-ADAPT)
- Wire connectors (3)
- Screws (2)
- Works with energy efficient dimmable light bulbs:
- LED – up to 150 W
- Halogen – up to 600 W
- Incandescent – up to 600 W
Product Usage Instructions
Installation for lights with one wall switch (single-pole):
- Turn off power at the circuit breaker.
- Remove the existing switch from the wall.
- Remove the wallplate from the switch.
- Disconnect all three wires from the switch.
- Connect the bare copper (or green) ground wire from the wallbox to the green wire on the dimmer using a wire connector.
- Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
- Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
- Mount the dimmer using the provided screws.
Using the dimmer with a smartphone or tablet (hub required, sold separately):
Note: If you are using the dimmer and remote control with another manufacturer’s hub, please refer to that manufacturer’s instructions for set- up.
- Download the Lutron app on your smartphone or tablet.
- Follow the app’s instructions to set up the dimmer and remote control.
FAQ:
Q: Where can I find a list of compatible dimmable LEDs?
A: You can find a complete list of compatible dimmable LEDs at
www.casetawireless.com/bulblist.
Q: What should I do if my dimmable LED bulbs flicker or turn off?
A: If you’re using dimmable LED bulbs and they flicker or turn off,
please visit www.casetawireless.com/lowend
for information on adjusting the dimmer for best bulb performance.
Q: Where can I find installation instructions for lights with more than
one switch (3-way)?
A: If your light has more than one switch (called a 3-way), please visit
www.casetawireless.com/3way for complete
installation instructions and how-to videos.
Pico remote control & in-wall dimmer
Welcome—and thank you for purchasing a Caséta by Lutron dimming kit. In order
to control your lights from an app or remote, you’ll need to replace an
existing switch with a Caséta by Lutron in-wall dimmer.
Before you install the dimmer, please watch the installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of Caséta by Lutron!
Double your warranty
Love Caséta dimmers? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register
Contents supplied
Tools you’ll need
Installing your dimmer
Installation for lights with one wall switch (single-pole)
Turn power off at circuit breaker
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off power at circuit breaker or
fuse before installing.
Important note:
Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). We’ve included instructions for lights with one wall switch (called a single-pole). If your light has more than one switch (called a 3-way),please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.
Remove existing switch from wall
Remove the wallplate from switch.
Remove the switch and pull it away from the wall.
Disconnect all three wires* from the switch.
If your switch has more than 3 wires attached, see “Installing Caséta in a 3-way switch application” video at www.casetawireless.com/3way
Remove side sections (if necessary)
Do not remove outside side sections on dimmers at the end of gang.
Important note:
Removing side sections reduces the dimmer’s maximum wattage rating. See the
chart below for maximum wattage information.
Maximum* wattage derating chart (120 V~ 50/60 Hz)
For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging
Connect the dimmer
- Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using a wire connector.
- Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
- Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
Mount the dimmer
Use the screws provided.
Attach the wallplate
Attach the adapter to the dimmer using the screws provided and snap on the wallplate.
(If you installed the dimmer next to other dimmers or switches, you’ll need to install a wallplate with the correct size / number of openings to accommodate all the devices.)
Turn power on at circuit breaker
Works with energy efficient dimmable light bulbs:
NOTE: You can mix and match dimmable LED, halogen and incandescent light
bulbs, with Caséta dimmers.
Dimmable LED light bulbs vary in their dimming performance.
If you’re using these bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend for
information on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs, please visit
www.casetawireless.com/bulblist
Using your Caséta by Lutron kit
With a smartphone or tablet (hub required, sold separately)
Note: If you are using the dimmer and remote control with another manufacturer’s hub, please refer to that manufacturer’s instructions for set- up.
Download the Lutron app
Launch the Lutron app
Use the Lutron app to complete ALL remaining steps
Without a smartphone or tablet
(hub not required)
Pairing the dimmer and Pico remote control
Press and hold “off” button on dimmer
Press and hold “off” button on remote
Changing the favorite light level on the Pico remote control (optional)
You can use the round“favorite” button on the Pico remote control to recall a favorite light level. We’ve set it to 50%, but you can change it to any level you like.
Set desired light level on dimmer
Press and hold “favorite” button on remote
For advanced features, tips on how to use Caséta dimmers with CFLs and LEDs, the complete Caséta product line, and more, please visit www.casetawireless.com/features
Using your controls
Replacing light bulbs using FASS Pull the FASS switch out on the in-wall dimmer to remove power at the light socket.
Important notes:
- For indoor use only.
- Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Device Ratings
- In-wall dimmer
- PD-6WCL
- 120 V~ 50/60 Hz
- Pico remote control
- PJ2-3BRL
- 3 V- 10 mA
- (1) CR2032 battery (included)
CAUTION
Use only with permanently installed fixtures with dimmable LED, dimmable CFL,
halogen, or incandescent lamps. To avoid overheating and possible damage to
other equipment, do not use to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
CAUTION: Risk of Fire, Explosion, Leakage, and Burns. Do Not Recharge,
Disassemble, Heat Above 212 °F (100 °C) or Incinerate. This product contains a
lithium button / coin cell battery. Keep batteries away from children. If a
new or used lithium button/coin cell battery is swallowed or enters the body,
it can cause severe internal burns and can lead to death in as little as 2
hours. Always completely secure the battery compartment. If the battery
compartment does not close securely, stop using the product, remove the
batteries, and keep the batteries away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
The battery in this device contains Perchlorate Material
- special handling may apply. For more information, visit www.dtsc.ca.gov/hazardouswaste/perchlorate
Codes
Install in accordance with all national and local electrical codes.
Grounding
When no “grounding means” exist in wallbox, the National Electrical Code
(NEC®) allows a control to be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the
circuit is protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or remove green wire
before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Troubleshooting
| Symptoms | Probable cause and action |
|---|
Light does not turn on or
in-wall dimmer LEDs do not light up.
| • Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmer is in the Off position.
Light does not respond
to Pico remote control.
| • The dimmer failed to pair with Pico remote control; see Pairing the dimmer and Pico remote control.
• The dimmer is already at the light level the Pico remote control is sending.
• The Pico remote control is outside the 30 ft (9 m) operating range.
• The Pico remote control battery is low.
• The Pico remote control battery is installed incorrectly.
• Bulbs turn off while being dimmed.
• Bulbs turn on at high light level but do not turn on at a low
light level.
• Bulbs flicker or flash when
dimmed to a low light level.
| Verify bulbs are marked dimmable and visit www.casetawireless.com/ lowend
for information on adjusting the dimmer for best
bulb performance.
Go to www.casetawireless.com/support for additional troubleshooting suggestions.
Lutron, the Lutron logo, Caséta, Claro, FASS, Pico, and the design of the Pico
remote are trademarks or registered trademarks of Lutron Electronics Co., Inc.
in the US and/or other countries. Apple is a trademark of Apple Inc.,
registered in the U.S. and other countries.
AppStore is a service mark of Apple Inc. All other product names, logos,and
brands are property of their respective owners.
© 2014-2023 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
References
- casetawireless.com/register
- Caseta by Lutron | Smart Light Switches, Controls & Dimmers
- Installing Caséta for a light with two switches | Lutron
- Lutron Support Center | Lutron
- Application Notes | Caséta Wireless | Lutron
- Capacity Derating Charts
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
- dtsc.ca.gov/hazardouswaste/perchlorate
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>