nVent LENTON T-Series 32 mm Horizontal Sleeve Side Fill Owner’s Manual

June 16, 2024
nVent LENTON

nVent LENTON T-Series 32 mm Horizontal Sleeve Side Fill

Product Information

Specifications

  • Catalog Number: RBT1091HSA
  • Product Name: T-Series Horizontal Sleeve, Side Fill, 32 mm, #10
  • Material: Steel
  • Finish: Plain
  • 100% U.S. Domestic Content: Yes
  • Sleeve: Standard Length
  • Rebar Size, Metric: 32 mm
  • Rebar Size, US: #10
  • Diameter 1: 57 mm
  • Diameter 2: 41 mm
  • Length 1: 140 mm
  • Length 2: 70 mm
  • Length 3: 20 mm
  • Unit Weight: 1.340 kg
  • Designed to Meet: AASHTO;ABNT NBR 8548:1984;ACI 318 Type 1 (125% Specified Yield);ACI 318 Type 2 (Specified Tensile);ACI 349;ACI 359;AS3600;CAN/CSA – N287.2/.3/.4;IBC Type 1 (125% Specified Yield);IBC Type 2 (Specified Tensile);US Army Corps of Engineers;CAN/CSA – A23.3

Product Usage Instructions

1. Safety Precautions

Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.

2. Installation

Follow the steps below to install the T-Series Horizontal Sleeve:

  1. Ensure that the structure allows for side fill installation. The vent holes in the sleeve are designed to reduce air entrapment and ensure proper filling.
  2. Prepare the reinforcing bars to be spliced. They can be saw cut, flame cut, or sheared.
  3. Insert the reinforcing bars into the sleeve, making sure they are properly aligned.
  4. Fill the sleeve with the appropriate material until it is completely filled.
  5. Allow the material to cure according to the manufacturer’s instructions.
  6. Visually inspect the installed sleeve to ensure proper installation.

3. Maintenance

The T-Series Horizontal Sleeve does not require any specific maintenance. However, regular inspections should be conducted to ensure the integrity of the sleeve and its connection to the reinforcing bars.

FAQ

1. Are other sizes available?

Sizes not shown may be available by special order. Please contact your nVent LENTON representative for more information.

2. Where can I find additional product details and instruction sheets?

You can find additional product details and instruction sheets on the nVent website at www.nvent.com. You can also request them from your nVent customer service representative.

3. Can nVent products be used differently than indicated in the instruction sheets?

No, nVent products should only be installed and used as indicated in the product instruction sheets and training materials. Failure to follow the instructions and warnings may cause product malfunction, property damage, serious bodily injury, and void your warranty.

4. How can I contact nVent customer service?

You can contact nVent customer service in the following ways:

  • Europe Netherlands: +31 800-0200135
  • Europe France: +33 800 901 793
  • Europe Germany: 800 1890272
  • Other Countries: +31 13 5835404
  • APAC Shanghai: + 86 21 2412 1618/19
  • APAC Sydney: +61 2 9751 8500

Our Brands

nVent.com CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER All trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.

Introduction

The side fill horizontal T-Series sleeve has vent holes located 90 degrees from the tap hole to facilitate side fill installations when the interferences of the structure will not allow top filling. Vent holes are added to horizontal sleeves to reduce air entrapment and help ensure proper filling of the sleeve.

FEATURES

  • Designed to connect horizontal reinforcing bars and angular reinforcing bars up to 45 degrees
  • Used to splice the same diameter bars
  • Works with saw cut, flame cut and sheared bars
  • Can be visually inspected after installation
  • Available with extended sleeve lengths

PRODUCT ATTRIBUTES

  • Material: Steel
  • Finish: Plain
  • 100% U.S. Domestic Content: Yes
  • Sleeve: Standard Length
  • Rebar Size, Metric: 32 mm
  • Rebar Size, US: #10
  • Diameter 1: 57 mm
  • Diameter 2: 41 mm
  • Length 1: 140 mm
  • Length 2: 70 mm
  • Length 3: 20 mm
  • Unit Weight: 1.340 kg

Designed to Meet: AASHTO;ABNT NBR 8548:1984;ACI 318 Type 1 (125% Specified Yield);ACI 318 Type 2 (Specified Tensile);ACI 349;ACI 359;AS3600;CAN/CSA – N287.2/.3/.4;IBC Type 1 (125% Specified Yield);IBC Type 2 (Specified Tensile);US Army Corps of Engineers;CAN/CSA – A23.3

ADDITIONAL PRODUCT DETAILS

Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual. Sizes not shown may be available by special order. Contact your nVent LENTON representative for more information

DIAGRAMS

WARNING

nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.

North America

  • +1.800.753.9221
  • Option 1 – Customer Care
  • Option 2 – Technical Support

Europe

  • Netherlands:
    • +31 800-0200135
  • France:
    • +33 800 901 793

Europe

  • Germany:
    • 800 1890272
  • Other Countries:
    • +31 13 5835404

APAC

  • Shanghai:
    • + 86 21 2412 1618/19
  • Sydney:
    • +61 2 9751 8500

Our powerful portfolio of brands:

  • CADDY
  • ERICO
  • HOFFMAN
  • RAYCHEM
  • SCHROFF
  • TRACER

2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

nVent LENTON User Manuals

Related Manuals