nVent LENTON RBS354715 Horizontal And Vertical Packing Owner’s Manual
- June 16, 2024
- nVent LENTON
Table of Contents
nVent LENTON RBS354715 Horizontal And Vertical Packing
Product Information
Specifications
- Diameter: 13 mm
- Length: 381 mm
- Unit Weight: 0.010 kg
Features
The horizontal and vertical packing materials seal the gaps that can exist between the sleeve and reinforcing steel bar. The packing materials help ensure the molten filler material remains in the sleeve until it solidifies. The product features include:
- Heat-resistant
- Pliable material forms to the reinforcing steel contours
- Helps prevent leaking of molten filler material
Additional Product Details
Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.
Diagrams
Warning
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.
Contact Information
For any inquiries or support, please contact the following:
- Europe Netherlands: +31 800-0200135
- France: +33 800 901 793
- Germany: 800 1890272
- Other Countries: +31 13 5835404
- APAC Shanghai: + 86 21 2412 1618/19
- Sydney: +61 2 9751 8500
Brands
Our powerful portfolio of brands:
- nVent.com
- CADDY
- ERICO
- HOFFMAN
- RAYCHEM
- SCHROFF
- TRACER
Disclaimer
All trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.
Product Usage Instructions
Step 1: Preparation
Prior to using the product, ensure that you have read and understood all the instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.
Step 2: Placement of Packing Materials
The horizontal and vertical packing materials are designed to seal the gaps between the sleeve and reinforcing steel bar. Follow these steps to place the packing materials:
- Identify the gaps between the sleeve and reinforcing steel bar.
- Cut the horizontal and vertical packing materials according to the length required.
- Place the horizontal packing material over the gap horizontally.
- Place the vertical packing material over the gap vertically.
- Ensure that the packing materials form a tight seal and cover the entire gap area.
Step 3: Molten Filler Material
The packing materials help ensure that the molten filler material remains in the sleeve until it solidifies. Follow these steps to use the molten filler material:
- Prepare the molten filler material according to the instructions provided.
- Pour the molten filler material into the sleeve, making sure it fills the entire space.
- Allow the molten filler material to solidify completely before proceeding with further installation or usage.
Step 4: Safety Precautions
During the usage of this product, it is important to prioritize safety. Follow these safety precautions:
- Use appropriate personal protective equipment (PPE) such as gloves and safety glasses.
- Work in a well-ventilated area to avoid inhaling any fumes or gases.
- Avoid direct contact with the molten filler material to prevent burns or injuries.
- Follow all applicable safety guidelines and regulations.
Step 5: Maintenance and Storage
After usage, it is important to properly maintain and store the product for future use. Follow these guidelines:
- Clean any residue or debris from the packing materials and sleeve.
- Store the product in a dry and secure location away from direct sunlight or extreme temperatures.
Frequently Asked Questions (FAQ)
Q: What is the purpose of the packing materials?
A: The packing materials are designed to seal the gaps between the sleeve and reinforcing steel bar, ensuring that the molten filler material remains in the sleeve until it solidifies.
Q: Where can I find the detailed instructions and safety notices?
A: The detailed instructions and safety notices can be found in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.
Q: How should I dispose of the molten filler material?
A: Follow local regulations and guidelines for the proper disposal of the molten filler material.
Introduction
The horizontal and vertical packing materials seal the gaps that can exist between the sleeve and reinforcing steel bar. The packing materials help ensure the molten filler material remains in the sleeve until it solidifies.
FEATURES
- Heat-resistant
- Pliable material forms to the reinforcing steel contours
- Helps prevent leaking of molten filler material
PRODUCT ATTRIBUTES
- Diameter: 13 mm
- Length: 381 mm
- Unit Weight: 0.010 kg
ADDITIONAL PRODUCT DETAILS
Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.
DIAGRAMS
WARNING
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.
North America
- +1.800.753.9221
- Option 1 – Customer Care
- Option 2 – Technical Support
Europe
- Netherlands:
- +31 800-0200135
- France:
- +33 800 901 793
Europe
- Germany:
- 800 1890272
- Other Countries:
- +31 13 5835404
APAC
- Shanghai:
- + 86 21 2412 1618/19
- Sydney:
- +61 2 9751 8500
Our powerful portfolio of brands:
- CADDY
- ERICO
- HOFFMAN
- RAYCHEM
- SCHROFF
- TRACER
2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.