Handy THPDC-A Poly Dump Cart Owner’s Manual
- June 4, 2024
- Handy
Table of Contents
Owner’s Manual
OPERATOR’S MANUAL AND PARTS LIST
POLY DUMP CART THPDC-A
Spares & Support: 01793 333212
www.thehandy.co.uk
Before use please read & understand this manual, paying particular attention to the safety instructions.
Important Safety Instructions
- READ ALL INSTRUCTIONS CAREFULLY BEFORE USE.
- Do not load The Poly Dump Cart with more than 881Ibs(400kg). Do not use the dumping feature of the Poly Dump Can with more than 3991bs (181 kg).
- Do not allow children to use the Poly Dump Cart unsupervised. The Poly Dump Cart is not a toy.
- Always distribute the payload evenly over the surface of the tray.
- Do not load any items on the top edges of the plastic tray.
- If any parts become damaged, broken, or misplaced, do not use The Poly Dump Cart until replacement parts can be obtained.
- Do not operate or use on objects that can cause damage to the pneumatic tires or tubes. Do not inflate tires to more than 30 PSI / 2.1 BAR.
- SAVE THESE INSTRUCTIONS!
Assembly Instructions
Your Poly Dump Cart requires assembly. Account for all parts and hardware
before beginning assembly. If any parts are missing or damaged, or if you have
any questions or need additional instructions, call the helpline on 01793
333220.
Tools required for assembly: large flat screwdriver and socket set (or two
adjustable wrenches).
Step 1 Assemble the front bracket to the front frame using M8X20 bolts
(TH140.12). MB lock (TH140.16).10 8mm washers (TH140-19)
Step 2 Assemble rear bracket to rear frame and tub using Round head M8X30
bolts TH140-13 MB lock nuts TH140.16. 4PCS ID 8mm wide wing washers (TH140.18)
on the base of the tub. Use one washer inside the tub and one underneath the
nut (see Exploded Drawing for Assembly on page 4) Step 3 Assemble the lock to
the tub using Round head M8X20 bolts (T11140-14). MB lock nuts(TH140.16).4PCS
ID 8mm wide wing washers (TH140.18) on the base of the tub. Use one washer
inside the tub and one underneath the nut (see Exploded Drawing for Assembly
on page 4), Step 4 Place the tub into its dump position. Remove the front
screws from the rear frame. Take the front axle and frame and slide it over
the rear frame where the screws were lust removed. Once aligned, reinsert the
screws and refit the nuts. The rear frame, front frame, and tub should now all
be connected.
Step 5 Assemble the wheels using the M12 lock nuts (TH140-17). spacers
(TH140-21), and washers (TH140-20).
Step 6 Assemble the handle to the yoke using an M8X60 bolt (TH140-15). M8 lock
nut (TH140-16), and ID 8mm washer (TH140-19).
Using the Dumping Feature
To operate the dumping feature, pull the dumping release handle outward to
release the plastic bed from the locking mechanism. Lift up the release handle
to raise the can into the dumping position.
Returning the Plastic Bed to the Lowered Position
Move the plastic bed back down to the lowered position. Make sure the dumping
release handle is locked into place when the cart is in the lowered position.
CAUTION
DO NOT EXCEED THE MAXIMUM OVERALL LOAD CAPACITY OF 400KGS AND MAXIMUM DUMPING
LOAD CAPACITY OF 181KGS.
Exploded Drawing for Assembly
Parts List
TH140-1 Tub (1)
TH140-2 Lock (1)
TH140-3 Front Frame (1)
TH140-4 Rear Frame (1)
TH140-5 Front Bracket Assembly (1)
TH140-6 Rear Bracket (1)
TH140-7 Left Rear Brace (1)| TH140-8 Right Rear Brace (1)
TH140-9 Handle (1)
TH140.10 Coupling (1)
TH140.11 Wheel (4)
TH140-12 Bolt M8x20 (4)
TH140-13 Round Head Bolt M8x30 (4)
TH140-14 Round Head Bolt M8x20 (4)| TH140.15 Round Head Bolt M8x60 (1)
TH140-16 Lock Nut M8 (13)
TH140-17 Lock Nut M12 (4)
TH140.18 Wide Wing Washer ID 8mm (16) TH140.19 ID 8mm Washer (5)
TH140-20 Washer ID 12mm (4)
TH140-21 Spacer (4)
---|---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>