nVent LENTON RBW4558A T-Series Vertical Sleeve Owner’s Manual
- June 15, 2024
- nVent LENTON
Table of Contents
nVent LENTON RBW4558A T-Series Vertical Sleeve
Product Information
Specifications:
- Catalog Number: RBW4558A
- Material: Steel
- Finish: Straight
- 100% U.S. Domestic Content: Yes
- Sleeve: Standard Length
- Rebar Size, Metric: 50 mm
- Diameter 1: 86 mm
- Diameter 2: 60 mm
- Length 1: 203 mm
- Length 2: 102 mm
- Unit Weight: 4.63 kg
- Designed to Meet: AASHTO; ABNT NBR 8548:1984; ACI 318 Type 1 (125% Specified Yield); ACI 318 Type 2 (Specified Tensile); ACI 349; ACI 359; AS3600; CAN/CSA – N287.2/.3/.4; IBC Type 1 (125% Specified Yield); IBC Type 2 (Specified Tensile); US Army Corps of Engineers; CAN/CSA – A23.3
Product Usage Instructions
Safety Precautions:
Prior to installation, it is important to read and understand all of the
detailed instructions and safety notices provided in the nVent LENTON Cadweld
Rebar Splicing System Instruction Manual.
Installation:
To install the T-Series Vertical Sleeve, follow these steps:
- Ensure that the reinforcing bars to be connected are clean and free from any debris.
- Position the T-Series Vertical Sleeve over the ends of the bars to be spliced, ensuring that it is centered and aligned properly.
- If necessary, adjust the length of the sleeve to match the diameter of the bars.
- Secure the T-Series Vertical Sleeve in place using appropriate fasteners or welding techniques.
- Inspect the installation visually to ensure proper alignment and secure attachment.
Visual Inspection:
The T-Series Vertical Sleeve can be visually inspected after installation to ensure proper alignment and attachment. Check for any signs of misalignment, damage, or inadequate fastening.
Extended Sleeve Lengths:
The T-Series Vertical Sleeve is available with extended sleeve lengths for
specific applications. Contact your nVent LENTON representative for more
information on obtaining extended sleeve
lengths.
FAQ (Frequently Asked Questions):
-
Q: Can the T-Series Vertical Sleeve be used with angular reinforcing bars greater than 45 degrees?
A: Yes, the T-Series Vertical Sleeve is designed to connect vertical reinforcing bars and angular reinforcing bars greater than 45 degrees. -
Q: Can the T-Series Vertical Sleeve be used with different diameter bars?
A: Yes, the T-Series Vertical Sleeve is designed to splice the same diameter bars, but it can also be adjusted to match different diameter bars by adjusting the sleeve length. -
Q: What cutting methods are compatible with the T-Series Vertical Sleeve?
A: The T-Series Vertical Sleeve works with saw cut, flame cut, and sheared bars. -
Q: Are there any contact numbers for nVent LENTON representatives?
A: Yes, you can contact nVent LENTON representatives at the following numbers:- Europa Netherlands: +31 800-0200135
- Europa Germany: 800 1890272
- Other Countries: +31 13 5835404
- APAC Shanghai: +86 21 2412 1618/19
- Sydney: +61 2 9751 8500
Note : The information provided in this response is subject to change. For the most up-to-date specifications and details, please refer to the nVent LENTON official documentation or consult with a nVent LENTON representative.
CATALOG NUMBER
- RBW4558A
FEATURES
- Designed to connect vertical reinforcing bars and angular reinforcing bars greater than 45 degrees
- Used to splice the same diameter bars
- Works with saw cut, flame cut and sheared bars
- Can be visually inspected after installation
- Available with extended sleeve lengths
PRODUCT FEATURES
- Material: Stahl
- Finish: Gerade
- 100% U.S. Domestic Content: Ja
- Sleeve: Standard Length
- Rebar Size, Metric: 50 mm
- Diameter 1: 86 mm
- Diameter 2: 60 mm
- Length 1: 203 mm
- Length 2: 102 mm
- Unit Weight: 4,63 kg
Designed to Meet :
AASHTO; ABNT NBR 8548:1984; ACI 318 Type 1 (125% Specified Yield); ACI 318
Type 2 (Specified Tensile);
ACI 349; ACI 359; AS3600; CAN/CSA – N287.2/.3/.4; IBC Type 1 (125% Specified
Yield); IBC Type 2 (Specified Tensile); US Army Corps of Engineers; CAN/CSA –
A23.3
ADDITIONAL PRODUCT DETAILS
- Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System Instruction Manual.
- Sizes not shown may be available by special order. Contact your nVent LENTON representative for more information.
DIAGRAMS
WARNING
nVent products must be used by nVent’s product information sheets and training
materials installed and used. Information sheets are available at
www.nVent.com and from your nVent dealer. Customer
Service Representative. Improper installation, misuse, misapplication, or
other acts inconsistent with nVent’s instructions and warnings may result in
malfunctions, equipment damage, serious injury or result in death and
cancellation of the guarantee.
Nordamerika
+1.800.753.9221
Option 1 – Customer Care
Option 2 – Technical Support
Europa
Netherlands:
+31 800-0200135
France: +33 800 901 793
APAC
Shanghai:
+ 86 21 2412 1618/19
Sydney: +61 2 9751 8500
Our powerful portfolio of brands:
nVent.com CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER
© 2023 nVent. All nVent marks and logos are owned or licensed by nVent
Services GmbH or its affiliates. All other trademarks are the property of
their respective owners.
nVent reserves the right to change specifications without notice.
References
- Building a more Sustainable and Electrified World | nVent
- Building a more Sustainable and Electrified World | nVent
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>