suptek ML55B Mobile TV Cart Instruction Manual

suptek ML55B Mobile TV Cart

WARNING!

Severe personal injury and property damage can result from improper installation or assembly. Read the following warning carefully before beginning.

• If you do not understand the instructions or have any concerns or questions, please contact a qualified local installer.
• Do not install or assemble if the product or hardware is damaged or missing. If you require replacement parts, please contact your local distributor for assistance.
• This product fits most 21″-60″ LCD/plasma screen; load capacity up to 77 lbs/35kg.
• Do not use this product for anything other than the original purpose.
• This product contains moving parts, please use with caution.

Dimension

Parts

• Plastic fixing cover x1

• Long square  tube x2

• Short square tube x2

• Panel x1

• Caster x4

• Column x3

• Hook x2

• Spring fastener x2
  

• Welded base x1

• Head locking bracket x1

• Tray locking bracket x1
  

Screw package

• A: S3/S5/S6 Inner-hexagon Allen key

• B: M8*60 Inner-hexagon x1
  Φ8XΦ16X1 Washer x1

• C:M4*20 x4

• D:M5*25 x4

• E:M6*25 x4

• F:M8*25 x4

• G:Φ6XΦ12X1 Washer x

• H: Φ8XΦ14X11 Spacer x4
  Φ8XΦ14X6 Spacer x4

• I: M8x12 Inner-hexagon x8
  

Installation Instructions

Step 1 Installation of base

1. Insert the long square tubes and short square tubes into the welded base according to the 1 to 1, 2 to 2 markings.
   
   Tighten screw I with wrench A
   
   

Step 2  Installation of plastic fixing cover and column and base

1. Loosen the screw on the column with wrench A

2. Tighten the 2 columns

3. Re-insert the screw with wrench A
   

4. The installation is complete

5. Loosen the screw on the column with wrench A
   

6. Tighten the 2 columns

7. Re-insert the screw with wrench A
   

8. The installation is complete
   

Step 3 Installation of column and Tray Locking Bracket and head locking bracket

Head locking bracket must be in the same side as long tubes or it may tip over.

1. Use wrench A to loosen the screws on the tray locking bracket
   

2. Use wrench A to loosen the screws on the head locking bracket
   

3. Slip the tray locking bracket and head locking bracket into the column
   

4. Select the appropriate position, and tighten the screws on the head locking bracket with wrench A
   

5. Select the appropriate position, and tighten the screws on the tray locking bracket with wrench A

Step 4 Installation of panel and stand

Remove the pre-positioned screws Hang the panel into the column Then tighten the screws.

Complete the installation as shown

Step 5 TV and hooks installation

Preparation:
Check VESA patterns on the back of TV

Please use proper screws; leave room between TV and screw ! (please use higher spacer for long screws in case of TV damage).

Step 6 Installation of TV and stand

Need someone to lift the TV.

1. Hang the hooks into the panel, Available in three heights.
   

2. Insert the spring fasteners into the corresponding spring buckle positions.
   

3. Complete the installation of the spring fastener.

4. Pull the pull cord after hooking the hook into the panel
   

5. Adjust the screw tightness to adjust the TV angle.
   

Customer Support

after-sales@suptekmount.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>