Suptek MD9442 2 Desktop Screens Instruction Manual

June 14, 2024
Suptek

Suptek MD9442 2 Desktop Screens

Suptek-MD9442-2-Desktop-Screens-PRO

UNPACKING INSTRUCTIONS

  • Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
  • Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts.
  • Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

  • Install and operate this device with care.
  • Please read this instruction before beginning the installation, and carefully follow all instructions contained herein.
  • Use proper safely equipment during installation.
  • Please call a qualified installation contractor for help if you:
  • If you don’t understand these directions or have any doubts about the safely of the installation.
  • If you are uncertain about the nature of your wall, consult a qualified installation contractor.
  • Do not use this product for any purpose or in any configuration not explicitly specified in this instruction.
  • We hereby disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

PARTS

Suptek-MD9442-2-Desktop-Screens- \(1\)

INSTALLATION INSTRUCTION

Step 1 Install the Pole on a Desk

  • Option A: Clamp installation
1. Connect clamp support (c) and pole (a) with 3 pieces of M5x18 (f) and tighten it with wrench (i) (figure 1).
2. Connect clamp (b) and clamp support (c) with pre-positioned screws and choose proper hole sit according to the thickness of desk (figure 2). Tighten the plastic knob to fix the clamp (figure 3).![Suptek-MD9442-2-Desktop-Screens- \(2\)](https://manuals.plus/wp-content/uploads/2023/11/Suptek-MD9442-2-Desktop-Screens-2.jpg)
  • Option B: Grommet installation
1. Connect grommet support (c) and pole (a) with 3 pieces of M5x18 (f) and tighten it with wrench (1) (figure 1). Insert grommet support (c) into desk hole whose diameter is over 1.65in/42mm (figure 2).
2. Connect grommet (b) and grommet support (c) with pre-positioned screws and choose proper hole site according to the thickness of desk (figure 3). Tighten the plastic knob to fix the clamp (figure 4).![Suptek-MD9442-2-Desktop-Screens- \(3\)](https://manuals.plus/wp-content/uploads/2023/11/Suptek-MD9442-2-Desktop-Screens-3.jpg)

Step 2 Connect Swivel Arm and PoleSuptek-MD9442-2-Desktop-Screens-
\(4\)

  1. Place pole wire clip (g) on the pole (a).
  2. Place arm wire clip (h) on the swivel arm (d).
  3. Place swivel arm (d) on pole (a). Tighten with wrench (i) at proper position.

Step 3 Connect VESA Plate and Monitor

Suptek-MD9442-2-Desktop-Screens- \(5\)

Step 4 Connect Monitor and Mount

  • Insert monitor into the head of swivel arm.
  • Drive nut(o)in plate into screw hole of head sleeve.Suptek-MD9442-2-Desktop-Screens- \(7\)

Step 5 Angle Adjustment of Head Sleeve

  • Adjust head sleeve according to the needs in case of sagging of monitor.
  • To adjust height of fighten or loosen the screw, fix plate by tightening nut at proper position.

Step 6 Cable Management

  • Make adjustment with wrench (i). Manage cables with arm wire clip (h) and pole wire clip (g).Suptek-MD9442-2-Desktop-Screens- \(10\)

after-sales-eu@suptekmount.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals