suptek CS201 Single Black Floating Shelf with Strengthened Tempered Glass User Manual

suptek CS201 Single Black Floating Shelf with Strengthened Tempered Glass

Specifications

• Model: CS201
• Weight Capacity: 17.6 lbs. (8 kg)

Product Usage Instructions

Important Notice

Before installing the product, ensure that you have received all the parts listed in the component checklist. If any parts are missing or faulty, contact the franchiser for a replacement.

Installation Precautions

• Read and understand all the instructions and warnings in the installation sheet before starting the installation process. If you have any questions or concerns, please contact your local distributor or the provided email address.
• Refer to the installation guide for the recommended distance from the wall to avoid property damage.
• This product should only be installed by someone with good mechanical experience, basic building knowledge, and full understanding of the instructions.
• Ensure that the supporting surface can safely support the equipment and all attached hardware and components, considering the combined load.
• If mounting to wood wall studs, make sure to anchor the mounting screws into the center of the studs. It is highly recommended to use an edge-to-edge stud finder.
• Never exceed the maximum load capacity of the product.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but avoid over-tightening, as it can damage the items and reduce their holding power.
• This product is intended for indoor use only. Using it outdoors could lead to product failure and personal injury.

Tools Required

• Phillips Head Screwdriver (200mm length, excluding the handle)
• Electric drill and 8mm masonry bit for concrete wall installation
• Marking Pen
• Hammer

Wood Stud Wall Mounting

1. Use a stud finder to locate the edges of the studs. It is highly recommended to use an edge-to-edge stud finder.
2. Based on the edges of the studs, draw a vertical line down the center of each stud.
3. Place the wall plate on the wall as a template and mark the center of the four mounting holes. Ensure that the mounting holes are on the centerline of the stud.
4. Drill four 1/8″ (3mm) diameter holes, 1.2″ (30mm) deep.
5. Secure the wall plate using four screws (A), ensuring that the wall plate is level.

Solid Brick and Concrete Block Mounting

1. Use the wall plate as a template to mark the locations of the four holes on the wall.
2. Pre-drill these holes with an 8mm masonry bit, ensuring a depth of at least 50mm.
3. Insert a Concrete Anchor (B) into each of these holes.
4. Attach the wall plate to the wall using four screws (A), ensuring that the wall plate is level.

Assembling The Glass Holder

Attach the connect piece to the glass holder using two screws and leave a space reserved of 3mm as shown in fig.2.1. Repeat the same method to assemble the other glass holder.

Installing The Glass Holder

Insert the glass holders into the wall plate along the wall plate rail at the desired height respectively, and then tighten two screws with a 3mm Allen key as shown in fig.3.1.

Installing The Glass Shelf

Gently place the glass shelf on the glass holders respectively. Attach the glass shelves to the glass holders using screws and plastic bushes. Tighten screws with a 3mm Allen key, but do not tighten completely at this time. Center the glass shelves over the holes and securely tighten the screws with a 3mm Allen key as shown in fig.4.1.

FAQ (Frequently Asked Questions)

Q: Can this product be used outdoors?

A: No, this product is intended for indoor use only. Using it outdoors could lead to product failure and personal injury.

Q: What is the maximum weight capacity of this product?

A: The maximum weight capacity of this product is 17.6 lbs. (8 kg).

Q: What tools are required for installation?

A: The tools required for installation include a Phillips Head Screwdriver (200mm length, excluding the handle), an electric drill with an 8mm masonry bit for concrete wall installation, a marking pen, and a hammer.

Q: How should I secure the wall plate when mounting to wood wall studs?

A: Make sure to anchor the mounting screws into the center of the studs. It is highly recommended to use an edge-to-edge stud finder for accurate placement.

What is your wall made of?

WARNING

• Do not begin the installation of the product before you have r ead amd understood the instructions and warnings contained in this installation sheet. if you have any question regarding any of the instruction or warning, please contact you r local distributor
• Please refer to installation guide recommendation for required distance from wall to avoid risk of property damage.
• This product should only be installed by someone of good mecha nical aptitude,with experience and basic building, and fully understands.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud fin der is highly recommended.
• Always use an assistant or mechanical lifting equipment to saf ely lift and position equipment.
• Tighten screws firml y, but do not over tingten. Over tightening can damage the items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could lead to product failure and personal injury

IMPORTANT:
Ensure you have received all parts against the component checklist prior to installing. If any parts are missing or faulty, call the franchiser for a replacement

PARTS

Tools required

• Phillips Head Screw driver (200mm length exclude the handle)
• Electric drill and 8mm masonry bit for concrete wall installation
• Marking Pen
• Hammer

WOOD STUD WALL MOUNTING

• Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended.
  Based on their edges, draw a vertical line down each stud’s center.

• Place wall plate on wall as a template. And mark the center of the four mounting holes. Make sure that the mounting holes are on the centerline of stud.

• Drill four 1/8”(3mm) dia. Holes 1.2”(30mm) deep. Secure it using four screws(A), make sure that the wall plate is level as shown in fig.1.1.

SOLID BRICK AND CONCRETE BLOCK MOUNTING

• Use the wall plate as a template to mark four holes locations on the wall as shown in fig.1.2.
• Pre-drill these holes with a 8mm masonry bit and depth is at least 50mm.
• Insert a Concrete Anchor(B) into each of these holes. Attach the wall plate to the wall using four screws(A), make sure that the wall plate is level as shown in fig.1.2.

Assembling The Glass Holder

• Attach the connect piece to the glass holder using two screws and space reserved 3mm as shown in fig.2.1
• Use the same method to assemble the other glass holder

Installing The Glass Holder

Insert the glass holders into the wall plate along the wall plate rail at the desired height respectively, and then tighten two screws with a 3mm Allen key as shown in fig.3.1.

• Insert two decorative covers to the top and bottom of wall plate respectively and install two plastic covers as shown in fig.3.2.
• You can adjust the height of the glass holders as needed. Loosen the screws with a 3mm Allen key(but not remove) to adjust the glass holders at the desired height and then tighten screws with a 3mm Allen key as shown in fig.3.2.

Installing The Glass Shelf

Place the glass shelf gently on the glass holders respectively. Attach the glass shelves to the glass holders using screws and plastic bushes, tighten screws with a 3mm Allen key but not tighten completely at this time. Center the glass shelves over holes, securely tighten screws with a 3mm Allen key as shown in fig.4.1.

Cable Management

After installing the DVD wall mount, place DVD gently on the mounted glass shelves. Pull out the cable clip, insert the cable into any of the opening of the clip, with one head of the cable inserted in the clip, insert the clip into the main pole, take out the other head of the cable from another opening of the clip, then push the clip until the end of the main pole.

Maintenance

• Once you have mounted the DVD bracket, Check that they are sufficiently secured and safety to use. You should check whether screws are fixed well every two months.
• If you have any doubts regarding the installation, please consult our retailer or service department for details.

after-sales@suptekmount.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>