USX MOUNT XAS502 Universal Speaker Stands Instruction Manual
- June 16, 2024
- USX-MOUNT
Table of Contents
USX MOUNT XAS502 Universal Speaker Stands
Product Information
Specifications
- Maximum Weight : 11 lbs. (5 kg)
- Tools Needed (not included):
- Tape Measure
- Open-end wrench
Parts and Hardware
Step 1
- a–M4X30 bolt 2pcs
- b–M6X30 bolt 2pcs
- c–M6X24 key hole bolt 2pcs
- 01 M6X12 bolt 2pcs
- 02 M6X10 bolt 2pcs
- d–M6 Butterfly Nut 2pcs
- e–M4 washer 2pcs
- f–M6 spacer 2pcs
- 03 M4X4 bolt 2pcs
- 04 M6 Carpet Nail 8 pcs
Step 2
- 08 Base 2pcs
- 10 Bottom tube 2pcs
- 09 Adjusting tube 2pcs
- Velcro x6
- 05 M6 Carpet Nut 8 pcs
- 06 Speaker attachment unit 2pcs
- 07 Allen key 1pc
Product Usage Instructions
Step 1: Assemble Product
1-1 Insert bottom tube 10 into base 08, then fasten bolt 02 by using Allen key 07.
Option: If the stand is placed on carpet, spin to loosen and remove the rubber feet, install the carpet nail 04 and screw to the end, then use the nut 05 to tighten the nail.
1-2 Insert Adjusting tube 09 into bottom tube 10 and use Allen key 07 to fasten bolt 03.
1-3 Attach the Speaker attachment unit 06 to the Adjusting tube 09 and fasten it with bolt 01.
Installation method of wires
- Method 1: Pass the wire through the internal connection of the product
- Method 2: Fix the wire directly on the surface of the product tube with Velcro
Step 2: Attach speaker to assembled stand
Option 1: According to your speaker’s installation hole, choose bolt a/b, washer(e), and spacer (f) to attach it. Then plug in the wires.
For inset hole
- Use bolt (a/b), washer (e), and spacer (f) to attach the speaker
- M4 washer (e) is only for M4 bolt (a) installation, while no washer is required for M6 bolt (b) installation
Option 2: For a speaker with a keyhole, attach keyhole bolt (c) to the speaker attachment unit 06 with butterfly nut (d).
Place the speaker on the stand with the keyhole bolt (c) inserted in the keyhole, then tighten the butterfly nut (d) and plug in the wires.
Step 3: Height Adjustment
Loosen the handle, and adjust the tube 09 to the desired height, then tighten the handle.
Frequently Asked Questions (FAQ)
Q: What is the maximum weight this product can hold?
A: The maximum weight this product can hold is 11 lbs. (5 kg).
Q: Are all the tools needed for assembly included?
A: No, the tools needed for assembly (tape measure and open-end wrench) are
not included.
XAS502
INSTRUCTION MANUAL
If you have any questions along the way, just message to us. We’re ready to help!
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS.
Dimensions
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
Parts and Hardware for STEP 2
STEP 1 Assemble Product
- Insert bottom tube 10 into base 08 , then fasten bolt 02 by using Allen key 07 Option: If the stand is placed on carpet, spin to loosen and remove the rubber feet, install the carpet nail 04 and screw to the end, then use the nut 05 to tighten the nail.
- Insert Adjusting tube 09 into bottom tube 10 and use Allen key 10 to fasten bolt 03.
- Attach the Speaker attachment unit 06 to the Adjusting tube 09 and fasten it with bolt 01.
Installation method of wires
Method 1: Pass the wire through the internal connection of the product;
Method 2: Fix the wire directly on the surface of the product tube with
Velcro.
Step 2 Attach speaker to assembled stand
-
Option 1: According to your speaker’s installation hole, choose bolt a/b,washer(e) and spacer (f) (as shown in Figure 1 and 2) to attach it.Then plug the wires.
For inset hole: Use bolt (a/b), washer (e) and spacer (f) to attach the speaker. M4 washer (e) is only for M4 bolt (a) installation, while no washer is required for M6 bolt (b) installtion. -
Option 2: For speaker with a key hole attach key hole bolt (c) to the speaker attachment unit 06 butterfly nut (d). ****
Place speaker on stand with key hole bolt (c) inserted in the key hole, then tighten the butterfly nut (d) and plug the wires.
Step 3 Height Adjustment
Loosen the handle, and adjust the tube 09 to desired height 09 ,then tighten the handle.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>