USX MOUNT XML018-1-01 Full Motion TV Mount Instruction Manual

June 10, 2024
USX-MOUNT

USX MOUNT XML018-1-01 Full Motion TV Mount Instruction Manual
USX MOUNT XML018-1-01 Full Motion TV Mount

CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS Concrete Install

Before getting started, let’s check below lists to make sure it is just right for you!

  1. Check your TV VESA is within Min and Max size
    MAX:600mm/23.62″
    (MIN:200mm/7.87″)
    Diminsion
    No? This mount is NOT compatible.
    Yes? Perfect !

  2. Does your TV (including accessories) weigh MORE than 150 lbs. (68.2 kg)?

CAUTION: DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in collapse of the mount and its accessories, causing possible injury

  1. What is your wall made of?
    Drywall with wood studs?

CAUTION: DO NOT install into drywall alone
Solid concrete

Unsure?
Mail to us via Amazon.

  1. Do you have all the tools needed? (NOT INCLUDE)
    Tape Measure

Pencil

Screw driver

Electric Drill
Electric Drill
Socket Wrench

Wood Stud Install
Stud Finder

7/32 in. (5.5 mm)
Wood Drill Bit

Concrete Install
3/8 in. (10 mm)
Masonry Drill Bit

Hammer

  1. CAUTION
    • This product is designed for use in wood stud, solid concrete walls – DO NOT install into drywall alone
    • The wall must be capable of supporting five times the weight of the TV and mount itself
    • Do not use this product for any purpose not explicitly specified by manufacturer
    • Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

Dimensions

TV INTERFACE
Dimensions
3-D

WALL PLATE
Dimensions
TOP VIEW – EXTENDED
Dimensions
SIDE VIEW – RETRACTED

FULLY ASSEMBLED MOUNT
Dimensions
TOP VIEW – RETRACTED
Dimensions
TOP VIEW – EXTENDED

Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service. Never use damaged parts!

NOTE: Not all hardware included will be used

Parts and Hardware for STEP 1

Brackets
Parts and Hardware
07 x2

TV Screws

M6x12mm

a x4
M6x35mm
Parts and Hardware
c x4
M8x25mm
Parts and Hardware
b x4
M8x45mm
Parts and Hardware
d x4

Spacers
M8x22mm

e x4
10mm

f x4
2.5mm

g x8
M6x17mm

h x4

Washers

M6

i x4

Parts and Hardware for STEP 2

Wall Plate
Parts and Hardware
06 x1
Lag Bolt

01 x4
4MM Allen Key

02 x1
M5x10mm Bolt

03 x4
End support
Parts and Hardware
05 x2
M6x16mm Bolt

04 x2
Mounting template
Parts and Hardware
Level x1

Velcro x3
Parts and Hardware

Concrete wall anchor (NOT INCLUDED)

Concrete Wall Anchor 4pcs

Contact us and message to us to have these additional pieces shipped directly to you.

Assemble End Supports to Wall Plate

Put the and supports 05 into wall plate 06 by using allen key 02 to fasten bolt 03
Assembly Wall Plate

STEP 1 Attach Brackets to TV

Select TV Screws
Assembly Wall Plate

Figure out the suitable position of brackets

LOW MOUNTING HOLES
Assembly Wall Plate
HIGH MOUNTING HOLES
Assembly Wall Plate
INSTALL UP/DOWN IF NEEDED
Assembly Wall Plate
TV BRACKETS MUST BE LEVEL
Assembly Wall Plate

Need Spacer?

  1. No, choose suitable screws and washers.
    Assembly Wall Plate

  2. Yes, choose suitable screws, washers and spacers.
    Assembly Wall Plate
    Tips: If you need to combine M6/M8( b/c/d ) screws with 2.5mm spacers( g ), you have to remove the inner circle.

Attach the TV Plate
Assembly Wall Plate

STEP 2A Attach Wall Plate to Wall Wood Stud Option

CAUTION: Avoid potential personal injury or property damage!

  • Drywall covering the wall, must not exceed 5/8 in. (16 mm)
  • Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
  • Maximum horizontal space between fasteners: 24 in. (609 mm)
  • Stud center must be verified
  1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
    Assembly Wall Plate

  2. Position the mounting template at your desired height and line up the holes with your stud center line. Level the mounting template and mark the hole locations.
    Assembly Wall Plate

  3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
    IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs.
    Assembly Wall Plate

  4. Install wall plate using lag bolts . Tighten the lag bolts only until they are pulled firmly against the wall plate.
    Assembly Wall Plate
    CAUTION: Improper use could reduce the holding power of the lag bolt.
    DO NOT over-tighten the lag bolts.

STEP 2B Attach Wall Plate to Solid Concrete Wall

CAUTION: Avoid potential personal injury or property damage!

  • Mount the wall plate assembly unit directly onto the concrete surface
  • Minimum solid concrete thickness: 8 in. (203 mm)
  1. Position the mounting template on the wall at your desired height. Level the mounting template and mark the hole locations.
    Assembly Wall Plate

  2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
    Assembly Wall Plate
    IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).

  3. Insert four anchors.
    CAUTION: Be sure the anchors are seated flush with the concrete surface.
    Assembly Wall Plate

  4. Insert wall plate 08 using lag bolts 01 . Tighten the lag bolts only until they are pulled firmly against the wall plate.
    Assembly Wall Plate
    CAUTION: Improper use could reduce the holding power of the lag bolt.
    DO NOT over-tighten the lag bolts.

STEP 3 Wall Plate Installation Integrity Test

Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.
Assembly Wall Plate

STEP 4 Hang and Secure TV to Wall Plate
Assembly Wall Plate

STEP 5 Adjustments

TV leveling adjustment (±3°):
Loosen 2 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level and retighten to secure.
Assembly Wall Plate

Tilting angle adjustment (+5°/-15°):
Loosen 2 handles (as below shown) at the same time to tilt TV to your desired angle and fasten fully after finished.

Assembly Wall Plate

TV side to side movement 8″:
Loosen four bolts by maximum 2 turns and need two people cooperation to lift the assembly unit (TV + TV plate + arms) at the same time slide it left or right along the rail of the wall plate to perfectly position the TV. Then tighten the bolts after adjustment.
Assembly Wall Plate

Cables manage:
Manage TV cables orderly and guide them through the velcros.
Assembly Wall Plate

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals