USX MOUNT XTL009 UL Listed TV Wall Mount Tilting Brackets Instruction Manual

USX MOUNT XTL009 UL Listed TV Wall Mount Tilting Brackets

Product Information

Specifications

• TV Size Compatibility: 37-90 inches
• VESA Compatibility: MAX 600mm/23.62 (MIN 200mm/7.87) horizontally, MAX 400mm/15.75 (MIN 100mm/3.94) vertically
• Maximum Weight Capacity: 132 lbs (60 kg)

Check your TV

Ensure that your TV meets the following criteria:

• VESA size is within the specified range
• Weight is not more than 132 lbs (60 kg)

For 37-90″ TV

If you have any questions along the way, just message to us.
We’re ready to help!

CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS

Before Getting Started

Before getting started, let’s check below lists to make sure it is just right for you!

1. Check your TV VESA is within Min and Max size
2. Does your TV (including accessories) weigh MORE than 132 lbs. (60 kg)?
   • CAUTION: DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in collapse of the mount and its accessories, causing possible injury.
3. What is your wall made of?
4. Do you have all the tools needed? (NOT INCLUDE)
5. CAUTION
   • This product is designed for use in wood stud, solid concrete walls – DO NOT install into drywall alone
   • The wall must be capable of supporting five times the weight of the TV and mount itself
   • Do not use this product for any purpose not explicitly specified by manufacturer
   • Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

Dimensions

TV INTERFACE

WALL PLATE

SIDES VIEW

Parts and Hardware

WARNING

• This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
• Never use damaged parts!

NOTE: Not all hardware included will be used.

Parts and Hardware for STEP 1

Parts and Hardware for STEP 2

Concrete wall anchor (NOT INCLUDED)

• Contact us and message to us to have these additional pieces shipped directly to you.

Assemble Wall plate STEP 3

Installation Instructions

STEP 1: Attach Brackets to TV

• Select TV Screws
• Figure out the suitable position of brackets
• Need Spacer?
  1. No, choose suitable screws and washers.
  2. Yes, choose suitable screws, washers and spacers.
  3. Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle.
  4. Attach the TV Plate

STEP 2A: Attach Wall Plate to Wall Wood Stud Option

CAUTION: Avoid potential personal injury or property damage!

• Drywall covering the wall, must not exceed 5/8 in. (16 mm)
• Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
• Maximum horizontal space between fasteners: 24 in. (609.6 mm)
• Stud center must be verified

1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
2. Position the mounting template at your desired height and line up the holes with your stud center line. Level the mounting template and mark the hole locations.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
   • IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs.
4. Install wall plate 08 using lag bolts 01. Tighten the lag bolts only until they are pulled firmly against the wall plate.
   • CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.

STEP 2B: Attach Wall Plate to Solid Concrete Wall

CAUTION: Avoid potential personal injury or property damage!

• Mount the wall plate assembly unit directly onto the concrete surface
• Minimum solid concrete thickness: 8 in. (203 mm)

1. Position the mounting template on the wall at your desired height. Level the mounting template and mark the hole locations.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
   • IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).
3. Insert anchors.
   • CAUTION: Be sure the anchors are seated flush with the concrete surface.
4. Insert wall plate 08 using lag bolts 01. Tighten the lag bolts only until they are pulled firmly against the wall plate.
   • CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.

STEP 3: Hang and Secure TV to Wall Plate

• Before hanging TV, please conduct “wall plate installation integrity test” first.

STEP 4: Hang and Secure TV to Wall Plate

STEP 5: Adjustments

• Tilting angle adjustment (0°/-10°): Pull TV to your desired angle then fasten 2 tilting bolts with Allen key 03.

STEP 6: Take Down the TV from the Mount

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>