USX MOUNT XML030-K Full Motion TV Wall Mount Instruction Manual

June 14, 2024
USX-MOUNT

USX MOUNT XML030-K Full Motion TV Wall Mount

USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount-PRO

Product Information

Specifications:

  • Compatible TV Size: 42-82 inches
  • VESA Size Range: MIN 200mm x 100mm, MAX 600mm x 400mm
  • Maximum TV Weight: 120 lbs (54.5 kg)
  • Wall Compatibility: Wood stud, Solid concrete (DO NOT install into drywall alone)

Product Usage Instructions

Step 1: Check Compatibility

  1. Check if your TV’s VESA size is within the specified range.
  2. Ensure that your TV weight is not more than 120 lbs (54.5 kg).
  3. Determine if your wall is made of drywall with wood studs or solid concrete.

Step 2: Gather Tools
Make sure you have the following tools:

  • Tape Measure
  • Pencil
  • Screwdriver
  • Electric Drill
  • 1/2 in. (13 mm) Socket Wrench
  • Stud Finder
  • 7/32 in. (5.5 mm) Wood Drill Bit
  • 3/8 in. (10 mm) Masonry Drill Bit
  • Hammer

Step 3: Installation Guide
Wood Stud Install:

  1. Ensure that the wall is capable of supporting five times the weight of the TV and mount itself.
  2. Use a stud finder to locate the wood studs in the wall.
  3. Mark the position of the wood studs with a pencil.
  4. Drill pilot holes into the marked positions using a 7/32 in. (5.5 mm) wood drill bit.
  5. Attach the wall plate unit to the wood studs using suitable screws and a screwdriver.
  6. Attach the TV brackets to the back of the TV using the provided screws and a screwdriver.
  7. Hang the TV onto the wall plate unit by aligning the brackets with the wall plate unit.
  8. Secure the TV in place by tightening the screws on the TV brackets.

Concrete Install:

  1. Ensure that the wall is capable of supporting five times the weight of the TV and mount itself.
  2. Use a concrete drill bit to drill holes into the solid concrete wall.
  3. Insert concrete wall anchors into the drilled holes.
  4. Attach the wall plate unit to the concrete wall using suitable screws and a screwdriver.
  5. Attach the TV brackets to the back of the TV using the provided screws and a screwdriver.
  6. Hang the TV onto the wall plate unit by aligning the brackets with the wall plate unit.
  7. Secure the TV in place by tightening the screws on the TV brackets.

FAQ

  • Q: What should I do if my TV is not compatible with this mount?
    A: If your TV does not meet the VESA size requirements or weighs more than 120 lbs (54.5 kg), this mount is not compatible. Please contact us for further assistance.

  • Q: Can I install this mount on a drywall without wood studs?
    A: No, it is not recommended to install this mount into drywall alone. It should be installed on wood studs or solid concrete walls for proper support.

  • Q: What should I do if I don’t have all the required tools?
    A: Make sure you have all the necessary tools listed in the user manual. If you are missing any tools, please obtain them before proceeding with the installation.

CAUTION: PLEASE READ ENTIRE MANUAL PRIOR ! TO USE AND SAVE THESE INSTRUCTIONS

Before getting started, let’s check below lists to make sure it is just right for you!USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount-
\(1\)

Dimensions

USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(2\)

Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.

USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(3\) USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount-
\(4\)

INSTALLATION

STEP 1 Attach Brackets to TVUSX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount-
\(5\) USX-MOUNT-XML030-K-Full-Motion-TV-Wall-
Mount- \(6\) USX-MOUNT-XML030-K-Full-Motion-TV-
Wall-Mount- \(7\)

STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION: Avoid potential personal injury or property damage!

  • Drywall covering the wall, must not exceed 5/8 in. (16 mm)
  • Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
  • Maximum horizontal space between fasteners: 16 in. (406 mm)
  • Stud center must be verified
  1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.

  2. Position the mounting template at your desired height and line up the holes with your stud center line. Level the wall plate and mark the hole locations.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(8\)

  3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
    IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs.

  4. Install wall plate using four lag bolts . Tighten the lag bolts only until they are pulled firmly against the wall plate.
    CAUTION: Improper use could reduce the holding power of the lag bolt.
    DO NOT over-tighten the lag bolts.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-
Mount- \(9\)

STEP 2B Attach Wall Plate to Solid Concrete Wall
CAUTION: Avoid potential personal injury or property damage!

  • Mount the wall plate assembly directly onto the concrete surface
  • Minimum solid concrete thickness: 8 in. (203 mm)
  1. Position the mounting template on the wall at your desired height. Level the wall plate and mark the hole locations.

  2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
    IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm ).USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(10\)

  3. Insert four anchors.
    CAUTION: Be sure the anchors are seated flush with the concrete surface.

  4. Insert wall plate 05 using four lag bolts 01. Tighten the lag bolts only until they are pulled firmly against the wall plate.
    CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount-
\(11\)

STEP 3 Extension Arms and end support Assembly
Please make sure you install these extension arms in right direction.USX-
MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(12\)

STEP 4 Wall Plate Installation Integrity Test
Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-
Mount- \(13\)

STEP 5 Hang and Secure TV to Wall Plate
Hang TV/bracket assembly onto wall plate, wrap clips on bracket around extension arms and tighten them using bolts 03.USX-MOUNT-XML030-K-Full-
Motion-TV-Wall-Mount- \(14\)

STEP 6 Adjustments

  1. TV leveling adjustment (±4°): Loosen 4 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level, and retighten to secure.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(15\)
  2. Tilting angle adjustment (+5°/-15°): Pull TV to your desired angle then fasten 2 tilting bolts with Allen key 04.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(16\)
  3. Cables manage: Manage TV cables orderly and guide them through the velcros.USX-MOUNT-XML030-K-Full-Motion-TV-Wall-Mount- \(17\)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals