USX MOUNT XTL018-01 Advanced Tilt TV Wall Mount Instruction Manual
- June 14, 2024
- USX-MOUNT
Table of Contents
XTL018-01
INSTRUCTION MANUAL
XTL018-01 Advanced Tilt TV Wall
‘For 42-90″ TV
If you have any questions along the way, just message to us. We’re ready to
help!
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE
INSTRUCTIONS
Before getting started, let’s check below lists to make sure it is just right for you!
1 Check your TV VESA is within Min and Max size| No? This mount is NOT
compatible.
Yes? Perfect !
2 Does your TV (including accessories) weigh MORE than 120 lbs. (54.5 kg)?|
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
CAUTION: DO NOT exceed the maximum weight indicated. This mounting system
is intended for use only with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result in collapse of the mount
and its accessories, causing possible injury.
3 What is your wall made of?|
4 Do you have all the tools needed?
(NOT INCLUDE)| Wood Stud Install Concrete Install
5 CAUTION| ● This product is designed for use in wood stud, solid concrete
walls – DO NOT install into drywall alone
● The wall must be capable of supporting five times the weight of the TV and
mount itself
● Do not use this product for any purpose not explicitly specified by
manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect
assembly or use
Dimensions
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard
if swallowed. Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item
to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
Parts and Hardware for STEP 2
Concrete wall anchor (NOT INCLUDED) Concrete Wall Anchor Ø10x50mm 4pcs
Contact us and message to us to have these additional pieces shipped directly
to you.
STEP 1 Attach Brackets to TV
1-1 Select TV Screws
1-2 Figure out the suitable position of brackets
1-3 Need Spacer?
No, choose suitable screws and washers. screw C is connected with TV
Brackets 04 05 directly,do not need to be connected with Washers K I .
Yes, choose suitable screws, washers and spacers. screw f is connected
with TV Brackets 04 05 directly,do not need to be connected with Washers
k I .
Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ),
you have to remove the inner circle.
1-4 Attach the TV Plate
Please ensure that all four screws enter the VESA hole before tightening all
screws during installation.
STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION: Avoid potential personal injury or property damage!
- Drywall covering the wall, must not exceed 5/8 in. (16 mm)
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
- Maximum horizontal space between fasteners: 24 in. (609.6 mm)
- Stud center must be verified
-
Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
-
Position the wall plate unit at your desired height and line up the holes with your stud center line.
Level the wall plate and mark the hole locations. -
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. ! -
Install wall plate 0 3 using lag bolts 01 . Tighten the lag bolts only until they are pulled firmly against the wall plate. 03 01 !
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
Go to STEP 3 on PAGE 13.
STEP 2B Attach Wall Plate to Solid Concrete Wall
CAUTION: Avoid potential personal injury or property damage!
- Mount the wall plate assembly unit directly onto the concrete surface
- Minimum solid concrete thickness: 8 in. (203 mm)
-
Position the wall plate unit on the wall at your desired height. Level the wall plate and mark the hole locations.
-
Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). -
Insert anchors.
CAUTION: Be sure the anchors are seated flush with the concrete surface. -
Insert wall plate using lag bolts . Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
STEP 3 Wall Plate lnstallation lntegrity Test
Before hanging TV, please try to pull the mount to make sure that it has
been assembled on the wall tightly.
STEP 4 Hang and Secure TV to Wall Plate
Hang pre-assembled TV unit on wall plate by pulling the straps and loosen when
finish. STEP 5 Adjustments
Tilting angle adjustment (+2°/-15°)：
Loosen the handles to tilt your TV at desired angle and fasten when finish.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>