Salior SK2303D Baby Car Rearview Mirror User Guide
- September 21, 2024
- Salior
Table of Contents
SK2303D Baby Car Rearview Mirror
“`html
Specifications
- Product Size: 1181 inches
- Product Material: Mirror – ABS & Acrylic Lens
- Battery Capacity: 3000mAh (DC5V/1A)
- Charge Cable: 10-Feet USB-C to USB-A
- LED Lights: 37 LEDs
- Color Temperature: 3500K
- Remote Control Battery: CR2032
- Levels of Brightness: 10%, 25%, 40%, 55%, 70%, 85%, 100%
Product Usage Instructions
Initial Use Guide
- Remove the battery insulation tab from the remote control.
- Peel off the protective film from the acrylic mirror.
- Connect the power source for the first use.
Installation Guide
The mirror can be installed using adjustable straps with
velcro.
Charging the Mirror
Use the included 10-feet charging cable to connect the mirror to
a power source for charging.
Power Supply
The mirror can be powered by the built-in 3000mAh rechargeable
battery or via the included 10 feet charging cable connected to
your vehicle’s USB-A port or a power bank.
FAQ
Q: How do I know when the battery needs charging?
A: The battery indicator on the mirror will show a red light
when the battery is below 20%. It will show a yellow light when
charging is in progress and a green light when the battery is fully
charged.
Q: How do I adjust the brightness of the LED lights?
A: Use the remote control to adjust brightness levels with the +
and – buttons. There are 7 levels of brightness to choose from.
Q: What is the purpose of the timer mode?
A: The timer mode allows you to select either a 30-second or
60-second timer for the LED lights to automatically turn off after
the set time.
“`
180mm
Baby Car Rearview Mirror
250mm
LED lights
Acrylic mirror
BATTERY INDICATOR
360°
The rotating can be adjusted in 360 degrees
Red Light: Battery is below 20%–please charge immediately. Yellow Light: Charging in progress. Green Light: Battery is fully charged.
REMOTE CONTROL INSTRUCTIONS
ON/OFF
30S
60S
ON/OFF Use the remote control to turn the LED light on and off, or press the
button on the back of the mirror.
Adjust Brightness: With 7 levels of brightness, use the “+” and “-” buttons on
the remote control to select the appropriate brightness level.
30S Timer Mode: Select “30s” or “60s” on the remote to activate the timer. A
3-seconds breathing light will confirm
60S
signal receipt, and the light will turn off automatically after 30 or 60
seconds based on your selection.
Memory brightness: The brightness in always-on mode and timer mode will be set
to the last used brightness level; after the battery runs out and the power is
restored, the default brightness is 40%.
INITITAL USE GUIDE
1. Remove the battery insulation tab from the remote control. 2. Peel off the
protective film from the acrylic mirror. 3. It is recommended to connect the
power source for the first use.
INSTALLATION GUIDE
1.To install, detach the magic tape strap and wrap it securely around the headrest opposite the infant’s seat, ensuring a tight fit by fastening the magic tape clasp. 2.Pull the strap to fix the mirror to the headrest, ensuring it stays in place during travel. 3.Sitting in the driver’s seat, adjust the mirror to the best angle that allows for a clear and convenient view of the infant during driving. (Optionally, one can ask for assistance from a helper if available.) Note: Please ensure all components are correctly installed and securely fastened to ensure driving safety and the infant’s comfort.
Adjustable straps with velcro
CHARGING THE MIRROR
Use the included 10-feet charging cable to connect the mirror to a power
source for charging.
POWER SUPPLY
The mirror can be powered by the built-in 3000mAh rechargeable battery or via
the included 10 feet charging cable connected to your vehicle’s USB-A port or
a power bank.
SPECIFICATION
Product Size Product Material Battery Capacity
Charge Cable LED Lights
Color Temperature Remote Control Battery
levels of brightness
1181 inchcMirror: 10*6.5inch ABS & Acrylic Lens 3000mAh (DC5V/1A) 10-Feet USB-C to USB-A 37 LEDs 3500K CR2032 10%,25%,40%,55%, 70%,85%, 100%
ATTENTION
1. Read all instructions before use. 2. Avoid exposing the product to direct
sunlight, high temperatures, heating above 60°C, or incineration. 3. Do not
place on wet surfaces. 4. Do not open, crush, or subject to impact or
modification. 5. Discontinue use if you notice any unusual smell, heating, or
other abnormalities. 6. Dispose of responsibly by recycling; do not discard
with household waste. Use designated recycling systems or contact the retailer
for proper disposal.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>