USX-MOUNT XFM090-15 Fixed TV Wall Mount with Low Profile Instruction Manual
- June 14, 2024
- USX-MOUNT
Table of Contents
- Before getting started
- Tools For Using
- Dimensions
- Parts and Hardware
- STEP 1 Attach Brackets to TV
- STEP 2A Attach Wall Plate to Wall Wood Stud Option
- STEP 2B Attach Wall Plate to Solid Concrete Wall
- STEP 3 Wall Plate Installation Integrity Test
- STEP 4 Hang and Secure TV to Wall Plate
- STEP 5 Take Down the TV from the Mount
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
USX-MOUNT XFM090-15 Fixed TV Wall Mount with Low Profile
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS
Before getting started
Dimensions
Before getting started, let’s check below lists to make sure it is just right for you!
Check your TV VESA is within Min and Max size 1
- No? This mount is NOT compatible.
- Yes? Perfect !
Does your TV (including accessories) weigh MORE than 99 lbs. (45 kg)? 2
- No? Perfect – you may continue.
- No? Perfect – you may continue.
What is your wall made of? 3
-
Drywall with wood studs?
-
Caution DO NOT install into drywall alone
-
Solid concrete
-
Unsure?
Message to us via Amazon.
Tools For Using
Do you have all the tools needed? (NOT INCLUDE)
-
Tape Measure
-
driver
-
Pencil Screw
-
Electric Drill
-
Socket Wrench
Wood Stud Install
-
Stud Finder
-
Wood Drill Bit
Concrete Install
-
Masonry Drill Bit
-
Hammer
CAUTION
- This product is designed for use in wood stud, solid concrete walls – DO NOT install into drywall alone
- The wall must be capable of supporting five times the weight of the TV and mount itself
- Do not use this product for any purpose not explicitly specified by manufacturer
- Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Dimensions
TV INTERFACE
WALL PLATE
SIDE VIEW
Parts and Hardware
WARNING : This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
NOTE : Not all hardware included will be used
Parts and Hardware for STEP 1
Parts and Hardware for STEP 2
-
Lag Bolt M6x60mm A x4
-
Washers B1 x4
-
M6 Spacers 10mm B2 x8
-
Level B3 x1
-
Spacers 5mm C x8
TV Screws
Concrete wall anchor (NOT INCLUDED)
Concrete Wall Anchor s Ø10x50mm 4pcs
Contact us at telephone 1-800-460-0956 or message to us to have these additional pieces shipped directly to you.
STEP 1 Attach Brackets to TV
Select TV Screws
Figure out the suitable position of brackets
Need Spacer?
-
No, choose suitable screws and washers.
-
Yes, choose suitable screws, washers and spacers.
Attach the TV Plate
STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION : Avoid potential personal injury or property damage!
- Drywall covering the wall, must not exceed 5/8 in. (16 mm)
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
- Maximum horizontal space between fasteners: 16 in. (406.4 mm)
- Stud center must be verified
-
Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
-
Position the Wall plate 01 at your desired height and line up the holes with your stud center line. Level the Wall 01 and mark the hole locations.
-
Drill pilot holes using a 1/8 in. (3 mm) diameter drill bit.
IMPORTANT : Pilot holes must be drilled to a depth of 2.5in. (64 mm). Be sure to drill into the center of the studs. -
Install wall plate 01 using lag bolts A. Tighten the lag bolts only until they are pulled firmly against the wall plate.
-
CAUTION : Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 2B Attach Wall Plate to Solid Concrete Wall
CAUTION : Avoid potential personal injury or property damage!
- Mount the wall plate assembly unit directly onto the concrete surface
- Minimum solid concrete thickness: 8 in. (203 mm)
- Position the Wall plate 01 on the wall at your desired height. Level the Wall plate 01 and mark the hole locations.
- Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT : Pilot holes must be drilled to a depth of 2.5 in. (64 mm).
-
Insert anchors.
CAUTION : Be sure the anchors are seated flush with the concrete surface. -
Insert wall plate 01 using lag bolts A. Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
STEP 3 Wall Plate Installation Integrity Test
Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.
STEP 4 Hang and Secure TV to Wall Plate
STEP 5 Take Down the TV from the Mount
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>