USX-MOUNT SML021-24K Full Motion TV Wall Mount Instruction Manual
- June 14, 2024
- USX-MOUNT
Table of Contents
- IMPORTANT INSTRUCTIONS
- Dimensions
- Parts and Hardware
- STEP 1 Attach Brackets to TV
- STEP 2A Attach Wall Plate to Wall Wood Stud Option
- STEP 2B Attach Wall Plate to Solid Concrete Wall
- STEP 3 Extension Arms and end support Assembly
- STEP 4 Wall Plate Installation Integrity Test
- STEP 5 Hang and Secure TV to Wall Plate
- STEP 6 Adjustments
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Elite Gourmet EPB-1800 Elite Cuisine 17 Piece Personal Drink Blender
For 42-84″ TV
If you have any questions along the way, just message to us. We’re ready to
help!
IMPORTANT INSTRUCTIONS
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS !
Before getting started, let’s check below lists to make sure it is just right for you!
1 Check your TV VESA is within Min and Max size|
No? This mount is NOT compatible. Yes? Perfect !
2 Does your TV (including accessories) weigh MORE than 110 lbs. (50 kg)?|
No? Perfect – you may continue. Yes? This mount is NOT compatible.
| CAUTION: DO NOT exceed the maximum weight indicated. This mounting
system is intended for use only with the maximum weights indicated. Use with
products heavier than the maximum weights indicated may result in collapse of
the mount and its accessories, causing possible injury
3 What is your wall made of?|
|
Solid concrete
|
4 Do you have all the tools needed? (NOT INCLUDE)|
-
Tape Measure
-
Pencil
-
Screw driver
-
Electric Drill
-
Socket Wrench
1/2 in. (13 mm)
Wood Stud Instal
-
Stud Finder
-
Wood Drill Bit
Concrete Install
-
Masonry Drill Bit
-
Hammer
5 CAUTION|
- This product is designed for use in wood stud, solid concrete walls – DO NOT install into drywall alone
- The wall must be capable of supporting five times the weight of the TV and mount itself
- Do not use this product for any purpose not explicitly specified by manufacturer
- Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Dimensions
-
TV INTERFACE
-
WALL PLATE
-
FULLY ASSEMBLED MOUNT
-
TOP VIEW – EXTENDED
-
TOP VIEW – RETRACTED
-
3-D
-
SIDE VIEW – EXTENDED
-
SIDE VIEW – EXTENDED
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard
if swallowed. Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item
to your dealer; contact
Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
TV Brackets
TV Screws
-
M4x12mm
-
M4x30mm
-
M6x12mm
-
M6x35mm
-
M8x25mm
-
M8x45mm
Spacers
-
M8x22mm
-
10mm
-
2.5mm
-
M6x17mm
Washers
-
M4
-
M6
Parts and Hardware for STEP 2
-
Wall Plate Unit
-
Velcro x3
-
Mounting template
-
Lag Bolt
-
Level
Concrete wall anchor (NOT INCLUDED)
Concrete Wall Anchor Ø10x50mm 4pcs
Contact us and message to us to have these additional pieces shipped directly to you.
Parts and Hardware for STEP 3
-
M6x8mm Bolt
-
M6x16mm Bolt
-
M5x10mm Bolt
-
Allen Key
-
Extension Arm
-
Extension Arm
-
End Support
STEP 1 Attach Brackets to TV
Select TV Screws
Figure out the suitable position of brackets
Need Spacer?
STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION: Avoid potential personal injury or property damage!
- Drywall covering the wall, must not exceed 5/8 in. (16 mm)
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
- Maximum horizontal space between fasteners: 24 in. (609 mm)
- Stud center must be verified
-
Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder.
-
Position the mounting template at your desired height and line up the holes with your stud center line. Level the wall plate and mark the hole locations.
-
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. -
Install wall plate
**06**
using four lag bolts**01**
. Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
STEP 2B Attach Wall Plate to Solid Concrete Wall
CAUTION: Avoid potential personal injury or property damage!
- Mount the wall plate assembly
**06**
directly onto the concrete surface - Minimum solid concrete thickness: 8 in. (203 mm)
-
Position the mounting template on the wall at your desired height. Level the wall plate and mark the hole locations.
-
Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).
-
Insert four anchors.
CAUTION: Be sure the anchors are seated flush with the concrete surface. -
Insert wall plate
**06**
using four lag bolts**01**
. Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 3 Extension Arms and end support Assembly
Please make sure you install these extension arms in right direction.
STEP 4 Wall Plate Installation Integrity Test
Before hanging TV, please try to pull the mount to make sure that it has been
assembled on the wall tightly.
STEP 5 Hang and Secure TV to Wall Plate
Hang TV/bracket assembly onto wall plate, wrap clips on bracket around
extension arms and tighten them using bolts **03**
.
STEP 6 Adjustments
TV leveling adjustment (±4°): Loosen 4 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level, and retighten to secure.
Tilting angle adjustment (+5°/-15°):
Pull TV to your desired angle then fasten 2 tilting bolts with Allen key.
Cables manage: Manage TV cables orderly and guide them through the velcros.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>