Tell LC2600 Series 1-3 4 Inch Thick Door Instruction Manual
- June 15, 2024
- Tell
Table of Contents
Installation Instruction
LC2600 Series
LEVERSET IS PRESET FOR 1-3/4” THICK DOOR
*THRUBOLTS ARE PROVIDED AND RECOMMENDED FOR USE IN HIGH SECURITY DOORS.
INSTALLATION OPTIONS
If you are installing this lock in a previously drilled door, you should have
a 2-1/8” hole through the door. You may or may not have two additional 3/8”
holes above and below the larger hole. Theseallow the lock to be installed
using thru-bolts.
This lock may be installed with or without thru-bolts. Use of thru bolts is
high recommended. even if it requires that you drill the two additional holes.
(A drill guide is available to simplify this task.)
If you elect to install without thru-bolts, we recommend that you install some
of the provided selftapping screws through the inside spring cage to stabilize
the lock on the door.
If you do not stabilize the lock, it may eventually become misaligned.
Security Level
-
High level: install with thru bolts.
-
Mid level: install without thru bolts, but use support screws.
DOOR PREP
-
Check lock for proper backset and body outside thru bolt type before drilling.
-
Place paper template (supplied) on the door and mark for holes. Drill the cross-bore holes, and then the latch holes. NOTE: Cut notches on 2-1/8” cross-bore hole on both sides for metal doors (Refer to fig. 2)
-
Drill (2) 3/8” thru bolt holes half way thru from each side of door to prevent damaging door unless lock is to be installed without thru bolts then skip this step.
-
Mortise latch unit front 5/32” into door edge to dimensions shown in fig.2.
-
Insert latch unit with sleeve if hole is 1” dia, or without sleeve into 7/ 8” dia. Make certain that latch bolt bevel faces direction of closing door.
-
Drill two 1/8” dia. holes and secure latch unit with screws supplied.
DISASSEMBLE A LOCK
- Use push pin to disassemble inside lever.
- Disassemble inside rose assembly and inside mounting plate.
FIT FOR 1-3/8” DOOR THICKNESS
(For 1-3/4” thick door, skip to step 4 directly)
Adjust for door thickness as
follows:
- Remove 4 small screws holding outside mounting plate to outside trim. And remove two thru-bolt posts if posts are fixed on the outside trim.
- Rotate the outside mounting plate until the lock body aligns with the centerline of the door.
- Re-install the 4 small screws holding the outside mounting plate to the outside trim and 2 thru-bolt posts if lock is to be installed with thru-bolts.
INSTALL LOCK ONTO DOOR
4A:
Place lock body into position. Make sure that latch prongs engage chassis
housing, and slide engages latch tail.
IMPORTANT
DO NOT INSTALL INSIDE LEVER AND LOCK IF THE DOOR IS THICKER THAN 2”, THE CATCH
WILL BE COVERED BY INSIDE ROSE.
4C: Install inside spring cage
using thru-bolts or M6x12 bolts, but do not tighten completely yet
4D: Slide inside lever onto the spindle and check to see if
rotation is smooth. Adjust the radial clearance between the inside spring cage
and inside lever, if necessary. Tighten the thru-bolts or M6X 12 bolts.
RECOMMENDED: Install four self-tapping support screws through the spring cage
for added stability, if thru-bolts were not used.
4E: Insert push pin into
hole to depress catch and remove inside lever.
4F: Install inside rose, make
sure inside rose and inside spring cage are secure.
4G: Slide inside lever
onto spindle. Push lever completely onto spindle until it locks into place.
(Pull on lever to make sure that catch is fully engaged.)
INSTALL STRIKE
INSTRUCTIONS FOR CYLINDER REPLACEMENT (IF REQUIRED)
6A: 1. Turn key 75 ° clockwise 2. insert push pin into hole in
outside lever to depress catch. 3. Remove the outside lever.
6B: Once you have removed the outside lever it is easy to adjust
the lock for a different door thickness, if necessary. Just depress the catch
and rotate the outside trim until the lock body aligns with the ce.nterline of
the door. 
6C: Install cylinder and lever.
6D: Turn the key approximately 80 ° clockwise and push the lever
all the way onto the spindle and then turn the key back to normal position.
Template
IMPORTANT
- FOR HIGH SIDE OF BEVEL PLACE OUTSIDE LINE AT EDGE OF DOOR
- FOR FLAT DOORS PLACE CENTER LINE AT EDGE OF DOOR
- FOR LOW SIDE OF BEVEL PLACE INSIDE LINE AT EDGE OF DOOR
IMPORTANT
- FOR HIGH SIDE OF BEVEL PLACE OUTSIDE LINE AT EDGE OF DOOR
- FOR FLAT DOORS PLACE CENTER LINE AT EDGE OF DOOR
- FOR LOW SIDE OF BEVEL PLACE INSIDE LINE AT EDGE OF DOOR
1-800-433-4047
LC2600-2018-ENG
Documents / Resources
| Tell
LC2600 Series 1-3 4 Inch Thick
Door
[pdf] Instruction Manual
LC2600 Series 1-3 4 Inch Thick Door, LC2600 Series, 1-3 4 Inch Thick Door, 4
Inch Thick Door, Thick Door, Door
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>