MOUNTUP MU4003-A Single Monitor Mount Installation Guide
- June 15, 2024
- MOUNTUP
Table of Contents
**MOUNTUP MU4003-A Single Monitor Mount Installation Guide
**
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
BEFORE ASSEMBLY
- Please check and make sure all necessary accessories are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts.
- Please read and understand this manual carefully before installation.
WARNING
-
This product contains small items that could be a choking hazard if swallowed.
KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED. -
Improper installation, such as using the product for monitor over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Must Check Before Getting Started
Verify Your Monitor Specifications:
VESA Pattern (W × H):
75mm × 75mm / 3″ × 3″
100mm × 100mm / 4″ × 4″
MAX:
17.6 lbs (8 kg)
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage or injury.
Verify Your Desk Specifications:
C-clamp
Desk Thickness
0.39~1.97″ (10~50mm)
Perfect
Grommet
Φ0.39~2.36″
(Φ10~60mm)
Desk Thickness
0.39~1.97″ (10~50mm)
Perfect
Product Dimensions
Supplied Parts and Hardware
-
A (x1) VESA Plate
-
B (x1) Swivel Arm
-
C (x1) Clamp
-
D (x1) Pole
-
E (x3) Pad
-
F (x1) Wire Clip
-
G (x1) 5mm Allen Key
-
H (x1) 6mm Allen Key
-
Ⅰ (×4) Screw M4×12mm
-
Ⅱ (×4) Screw M4×25mm
-
Ⅲ (×4) Spacer H10mm
NOTE: Not all parts and hardware included will be used.
Base Installation
OPTION A: Clamp Installation
C-clamp
Desk Thickness
0.39-1.97″ (10-50mm)
Apply pad (E) to the pole (D) bottom to avoid desk scratches. Mount clamp (C)
to the bottom of pole (D) by tightening pre-assembled bolts (C6) with 5mm
Allen key (G). Then secure clamp to the desktop.
OPTION B: Grommet Base Installation
Grommet
Φ0.39~2.36″
(Φ10~60mm)
Desk Thickness
0.39-1.97″ (10-50mm)
Remove the plastic protector from the hole(if any). Detach bracket (C1) and
bolt (C2) from clamp (C). Apply pad (E) to the pole (D) bottom to avoid desk
scratches. Secure base to the desktop by using bracket (C1) and bolt (C2).
Arm Installation
Install wire clip (F) and swivel arm (B) to the pole (D). Fasten the bolt with supplied 6mm Allen key (H)
Please do not move stand outside desk for safety!
Attach VESA Plate to Monitor
Select Correct Monitor Screw Length
CAUTION: Too short will not hold your monitor. Too long will damage your monitor.
Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the
appropriate screws and spacers for your monitor.
For more spacing between bracket and monitor
For protruded back monitor
For counter bore of monitor
To avoid the blocked input
Do not tighten the screws excessively or tighten them by using the Electrode,
or your monitor might be damaged.
Hang Monitor
Remove pre-assembled security bolt (B0) from the swivel arm (B), save
it for using to next step. Slide the monitor onto the head of swivel arm
(B).
Secure the VESA plate to the arm with the removed bolt (B0) from the previous
step. Make sure the security bolt (B0) is installed before you rotate the
monitor.
Adjustments (If necessary)
Problem: If monitor face down
Solution:
- Loosen the tilting bolt.
- Adjust monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle
Cable Management
Run cables through the Wire Clip. Store Allen keys (G or H) in wire clip for
future use.
Adjust monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>