MOUNTUP MU2008 Dual Monitor Wall Mount Instruction Manual
- May 15, 2024
- MOUNTUP
Table of Contents
MOUNTUP MU2008 Dual Monitor Wall Mount
Specifications:
- Product Dimensions: 4.4″ (112mm) x 3.94″ (100mm) x 2.95″ (75mm)
- Weight Capacity: 4.4lbs – 17.6lbs (2kg – 8kg)
- Wall Plate: 1.59″ (40.5mm) x 6.65″ (169mm) x 5.59″ (142mm)
- Lag Bolt Size: ST6.3x65mm
- Concrete Wall Anchor Size: 10x50mm
Product Usage Instructions
Safety Precautions:
- Read the installation instructions carefully before proceeding.
- Ensure the wall is suitable for mounting the product – use in wood stud or solid concrete wall only.
- Verify that the wall can support five times the weight of the monitor and mount combined.
- Check for choking hazards in small parts before assembly.
Installation Steps:
- Verify all parts are included and undamaged before starting assembly.
- Identify the lower arm (A), upper arms (B), decorative covers (C), cable covers (D), VESA plates (E), bolts (F), Allen keys (G, H), lag bolts (W-A), concrete wall anchors (W-B), and bubble level (T).
- Follow the detailed installation guide provided in the manual for step-by-step assembly.
- Use the appropriate tools provided to secure the mount to the wall.
- Ensure the monitor weight does not exceed the specified capacity.
FAQ
- Q: What should I do if I encounter missing or damaged parts?
- A: Do not return the damaged item to your dealer; please contact our customer service team for assistance.
- Q: Can I install this product on a drywall?
- A: No, this product is designed for use in wood stud or solid concrete walls only. DO NOT install into drywall alone.
- Q: How do I ensure the safety of the installation?
- A: Read the safety precautions carefully, verify your wall construction, and follow the installation steps provided in the manual to ensure a secure installation.
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
- This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the monitor and mount combined.
- Incorrect installation may result in product damage/property damage or body injury.
We shall bear no responsibility for any damage or injury resulting from
incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard
if swallowed. Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item
to your dealer; please contact our customer service team. Never use damaged
parts!
Must Check Before Getting Started
Verify Your Monitor Specifications:
Verify Your Wall Construction
CAUTION:
Avoid potential personal injuries and property damage! Drywall covering the wall must not exceed 5/8 in (16 mm). Minimum wood stud size: nominal 2 x 4 in (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm).
CAUTION:
Avoid potential personal injuries and property damage! Mount the wall plate
assembly directly onto the concrete surface (no surface covering).
Attention
Tension adjustment should be done only after monitor installation
WARNING:
Gas Spring Arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury
Product Dimensions
Supplied Parts and Hardware
NOTE: Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
Attach a VESA Plate to Monitor
Select Correct Monitor Screw Length
Attach VESA Plate to Monitor
Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged
Attach Arm to Wall
- Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder
- Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.
- Drill pilot holes using a Ф3/16 in (Ф4.5mm) diameter drill bit.
- IMPORTANT:
- Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud.
Install wall plate using lag bolts with Socket Wrench, NO Electrodrill. No anchors when installed onto the wood studs.
CAUTION:
To avoid potential personal injury or property damage: All 3 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step. To prevent the TV falling down, the Arrow Must Keep UP at this step!!
Attach Arm to Wall
OPTION B: Solid Concrete Wall Installation
- Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.
- IMPORTANT:
- Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks.
Use the hammer to knock anchors into the concrete wall. Be sure the anchors are seated flush with the concrete surface. Install wall plate using lag bolts and anchors with Socket Wrench, NO Electrodrill.
CAUTION:
To avoid potential personal injury or property damage: All 3 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step. To prevent the TV falling down, the Arrow Must Keep UP at this step!
Hang Monitor
Install the Upper Arms (B) to the Lower Arm (A). Secure the arm by tightening
the inside screw using 3mm Allen key (G). Attach Decorative Covers (C) to the
wall plate.
Slide the monitor onto the head of swivel arm, install the security bolt (F). Make sure the security bolt is installed before you rotate the monitor.
Adjustments
Adjustments (If necessary)
Tilt Adjustment
- Loosen the tilting bolt.
- Adjust the monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
Tension Adjustment
The gas spring is pre-set for a load-bearing range of 8.8 lbs -13.2 lbs. For intended functioning of the mount, you will need to adjust the tension of Arm in accordance with your monitor weight by 6mm Allen Key (H).
- Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended.
- Solution:
- Turn the inside screw counterclockwise (“+” direction) to increase gas spring tension until the arm can stay as intended.
- Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.
- Solution:
- Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intende
Cable Management
Adjust monitor position and rotation
Documents / Resources
|
MOUNTUP MU2008 Dual Monitor Wall
Mount
[pdf] Instruction Manual
MU2008 Dual Monitor Wall Mount, MU2008, Dual Monitor Wall Mount, Monitor Wall
Mount, Wall Mount, Mount
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>