MOUNTUP MU6004 Dual Monitor Stand Height Adjustable Monitor Desk Mount Instruction Manual

MOUNTUP MU6004 Dual Monitor Stand Height Adjustable Monitor Desk Mount

If you have any questions, please feel free to contact our customer service via Amazon before returning.

WARNING!

BEFORE ASSEMBLY

• Layout all components and hardware. Check all parts are included and undamaged.
• Should anybody intends to install or use this mount, please read and understand this manual carefully.
• If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.

WARNING

• This product contains small items that could be a choking hazard if swallowed.
• KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
• Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury mounting or caused by improper inappropriate use.

CAUTION AND MAINTENANCE

• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

PACKAGE CONTENTS

ASSEMBLY STEPS

STEP 1: Apply Pads To The Base Bottom

Paste the Pad (E1) ooto the Base (El

STEP 2: Clamp Installation Or Grommet Base Installation

OPTION A: Clamp Installation
Loosen bolts (B4) by using 5mm Allen Key (I), then align the screw hole on the Base (E), and then lock the Screw (B4) with a 5mm Allen Key (I) .

Fix the Decorative Cover (C) to the Base (E) and fix the bracket on the table by tightening the Clamp (B).

OPTION B: Grommet Base Installation

Ensure the desktop has a hole between 0.39″-2.36″ (10mm-60mm) in diameter to use this option.

Use 5mm Allen Key(I) to detach Clip Plate(B2)and Bolt Y(B3) from Clamp(B).

Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (E) and the table board together.

STEP 3 : Arm Installation
Install Arm (A), Fixator(H) , Wire Clip (G) on the base in sequence as shown below.
Make sure to tighten the Fixator(H) to desired place with 5mm Allen Key(I}.
Adjust the tightness of the bolt of Arm(A) to make the rotation flexible.

STEP 4 : Attach Monitor

OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to back of monitor and secure with Screws(M-A) with Washers(M-C ) using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.

OPTION B: Curved Back Monitor
Attach the VESA Plate (D) to back of monitor and secure with screws (M-B) with Washers (M-C)and Spacer(M-D)using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.

NOTE: Hand tighten screws to avoid over-tightening.

STEP 5 : Hang Monitor

Slide the monitor onto the head of swivel arm.Install the Security Bolt (F).
Make sure the security bolt is tightened before you rotate the monitor.

Refer to below illustrations to adjust tilting angle of your monitor.

Problem:
If monitor face down

Solution:

1. Loosen the tilting bolt.
2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.

STEP 6 : Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).

Note:
Be sure to keep the arm in horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.

Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up
Upper Arm with monitor rises up and fails to stay where intended.

Solution:
Turn the inside screw clockwise(*-“direction) to decrease gas spring tension until the arm can stay as intended.

Note:
For how many circles the screw should be turned, please refer to the table below.

Monitor Weight| 2kg| 3kg| 4kg| 5kg| 6kg| 7kg| 8kg| 9kg
---|---|---|---|---|---|---|---|---
Circles(AT LEAST)| min| 2| 4| 6| 8| 10| 12| 15

STEP 7 : Cable Management

Remove bottom plastic covers from gas spring Arm (A} .Run cables from monitor through bottom of gas spring Arm (A}. Then cover the Wire Cap (A 1} onto the upper arm of the Arm (A}. Reattach plastic covers as shown in diagram.

1. Remove the cable cover using a 5mm Allen Key (I)
2. Fix the wire in the harness wire cover
3. lnstall and fix the harness cover on the Arm (A) using a 5mm Allen Key (I)

Adjust as Desired

Adjust monitor position and rotation

• Tilt
• S1 Swivel
• S1 Rotation

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously.
If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>