MiCODUS MV930G Car GPS Rastreador 4G Tracker User Manual

MiCODUS MV930G Car GPS Rastreador 4G Tracker User Manual

Main Features

• 4G LTE+ 2G GSM

• GNSS+LBS

• Remotely Cut Off /Resume Fuel

• Realtime Tracking

• Historical Route Playback

• Vibration Alarm

• 9-95V Wide Working Voltage

• ACC Status Detection

• Tow Alarm

• Power Disconnect Alarm

• Geo-fence

• Engine On/ OFF Alarm

• Battery low voltage alarm

• Overspeed Alarm

• Lifetime Free Tracking Platform

• iOS & Android

Specifications

4G LTE CAT1:LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20/B25/B26/B28/B66; LTE-TDD: B34/B38/B39/B40/B41
GNSS Specifications| GNSS| GPS+BDS+GLONASS
GPS Frequency| L1: 1575.42±1.023MHz
BDS Frequency| B1:1561.098±2.046MHz
Satellite Channels| 32
Hot/Cold Start| <1s，<32s @ Open Sky
GNSS Antenna| Built-in Ceramics GNSS Antenna, 25254mm
Positioning Type| GNSS+LBS+AGPS
Accuracy| Location accuracy: <10m（1σ）
Timing accuracy: <30ns（1σ）
Speed accuracy: <0.1m/s（1σ）

How to manage the tracker to get online?

Step 1
SIM card requirements

Please get a suitable SIM card from your local place. The SIM card must meet below points:

• It must be compatible with the 4G LTE or 2G GSM network
• Please enable SMS, call, internet data traffic of the SIM card
• Remove the PIN code
• Enable the caller ID display feature
• Use Nano size SIM card for the tracker
• Please inquire the SIM card provider for the exact correct APN information

Step 2
SIM card installation

Step 3

Wiring

NOTE: After installed SIM card correctly , it is very important to connect the tracker with external power no less than 12V for power supply before operation!

Step 4 Configure APN

the SIM card has APN user and APN password, then use this command.
APN, Apn Name#| SET APN OK| APN, internet#| If the SIM card operator doesn’t have APN user and APN password, then please use this command.

Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply “SET APN ok” but it will  can’t get online!

Step 5 Indicator status description

Device has not been turn on
Device ran out of battery

Package Content

GPS Main Unit: x 1
Funcion Cable: x 1
Pick: x 1
User Guide: x 1
Genuine Packing Box: x 1

Functions Explanation

a. Cut Off Fuel/Resume Fuel

• Set center number by this sms command:
  CENTER, A, center number#

• Send this sms command from the center number:
  RELAY,A#

A=0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately;
2: Cut Off Fuel Safely)

**For example:

**

b. Vibration Alert:

This vibration alert function just work under stationary status. How to use this function:

• Configure SOS numbers for the tracker by this sms command:
  SOS,A,1st number,2nd number,3rd number#
  3 SOS numbers supports at the most
  

• Enable the device to enter into arm mode by this
  sms command: ARM#

• Conifgure the alarm ways by this sms command:
  SENALM,[A][,M]#
  A=ON/OFF, default: OFF;
  M=0/1/2, way of alarming,
  0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1

• Keep the device under stationary status more than 5min to let it enter into sleep arm mode;

• Vibrate the device then the tracker will send the vibration alarm messages
  For example:
  

c. External Battery Low Voltage Alarm

• Command format: LVALM,A,B,M#
  A = ON/OFF, default :ON;
  B=9-95V (voltage alarm threshold) , default: 11.1v
  M=0/1/2, way of alarming, 0: Server only,
  1 : SMS + Server, 2: SMS + Server + Call, default:1；

For example: LVA LM,ON,11.5,1#
This means once the external battery voltage is less than 11.5v the device will send alarm message via server and sms.

d. Engine Start and Flameout Alarm

• Command format: ACCALM,A,B,M#

A=ON/OFF, Default: ON;
B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC
ON&OFF Alarm; Default:2
M: 0/1/2 (way of alarm): 0 : Server only,
1: SMS + Server, 2: SMS+ Server + Call, Default:1;
For example: ACCALM,ON,2,1#
For example:

This means once the device detects engine start and engine flameout it will send alarm message via server and sms .

Installation Recommendation

1. The device should face up to the sky.
2. Metal thermae barrier of heating layer of the windshield affects the signal.

Troubleshooting

Check whether the data service of SIM card is enabled. Check the balance of SIM card.
Tracker shows offline| Check whether external power is still connected. Check if the vehicle entered network blind area. Check the balance of SIM card.
Unable to locate| Make sure the top side facing upward without metallic things shielded.Make sure it’s not in area with no satellite coverage.
Location drift| In area with poor GNSS signal (tall building around or basement), drifting may happen.
Check whether vibration happens around to trigger the accelerator.
No command reply| Make sure command format is correct. Vehicle may be in network blind area.
Make sure SIM card is well inserted and has SMS service.

Full SMS Commands List

Setting Commands

Functions| Command Format| Explanation
APN Setting| APN,Network name[,name, password]#| APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password)

Server Setting

| If set with Domain Name: SERVER,1,Domain,Port#| SERVER,1,d.micodus.net,7700#
If set with IP: SERVER,0, IP,Port#| SERVER,0,47.254.77.28,7700#
Check IMEI| IMEI#| DEVICE IMEI No. : 0123456789
Change IMEI| IMEICHG,354188046912460#| NEW IMEI No. : 354188046912460
Restore factory settings| FACTORY#| RESTORE FACTORY SETTINGS OK
Restart device| RESTART#| RESTARTING…1 MINUTE WILL BE OK
Internet Traffic Switch| TRAFFIC,ON#| OPEN TRAFFIC OK
TRAFFIC,OFF#| CLOSE TRAFFIC OK

Time Zone Setting

|

GMT,A,B,C#

| Example:GMT,E,8# (Means East +8 zone, no half time zone)GMT,W,9,30# (Means West -9.5 zone, has half time zone)A: E / W, E: East time zone, W: West time zone B: 0 ~ 12; whole time zoneC: 0/15/30/45, half time zone

Set the angle upload

|

ANGLEREP,X,A,B#

| Example: ANGLEREP,ON,30,3# ( Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds)X=ON/OFF, default：ON;A=5～180 degrees, diversion angle degree, default: 30 degrees；B=2～5 seconds, detecting time, default: 3seconds,
ANGLEREP,OFF#| CANCEL UPLOAD ANGLE OK

Mileage Statistics

|

MILEAGE,A,B#

| Example: MILEAGE,ON,5000# (Means enable the mileage statistics feature, the mileage initial value is 5000km)A=ON/OFF, On/Off mileage calculation, default: Off B=0～999999，Mileage initial value , unit：km ;default: 0, mileage return to zero
MIELEAGE#| Query current mileage

Add SOS Administrator Number

|

SOS,A,1st number,2nd number, 3rd number#

| Example:Set 3 numbers at a time: SOS,A,13800138000,13800138001,13800138002#Set the first numberseparately: SOS,A,13800138000#Set the second number separately: SOS,A,,13800138001#Means to set 3rd number separately:SOS,A,,,13800138002#

Delete SOS Administrator Number

|

SOS,D,1st number,2nd number, 3rd number# or SOS,D,1,2,3#

| Example:Directly delete the number: SOS,D,13800138000#Delete 1st number: SOS,D,1#Delete 2nd number: SOS,D,2#Delete the 2nd and 3rd number: SOS,D,2,3#

Add Center Number

|

CENTER,A,center number#

| Example: CENTER,A,008613800138000# (Meansthe tracker will just can be controlled by this number 008613800138000, 0086 is country code)NOTE:1. Please set up the center number with the country code as prefix!2. After set up center number, the tracker will just can be controlled by center number, it will not reply commands from other numbers!
Delete Center Number| CENTER,D#| DEL CENTER OK

Data Upload Time Interval

|

TIMER,T1,T2#

| Example: TIMER,5,180# (Means the tracker will upload data every 5s when ACC is on and 180s when ACC is off)T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;
Heartbeat Packet Upload|

HBT,time#

| Example: HBT,3# (Means the tracker will send heartbeat data package to server every 3 min for connection maintenance)NOTE: Range :1-60min, default 3min.
Sensor Sensitivity| LEVEL,A#| Example: LEVEL,2# (Means set up the shake sensor level to 2)NOTE: A：Sensitivity Level 1-9 (1-9 is from week to strong vibration)
Arm manually| ARM#| Set the device into arm mode
Disarm manually| DISARM#| Set the device out of arm mode

Cut Off / Resume Fuel

|

RELAY,A#

| A=1/2;1: Enable relay immediately 2: Enable relay safelyFor Example:1. RELAY,1#A is set to 1, the relay command will be executed immediately.2. RELAY,2#A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.
RELAY,0#| RESUME FUEL OK
Inquiry Commands
Functions| Command Format| Explanation

Version Inquiry

|

VERSION#

| Device Reply Example: ID:9301074948 IMEI:354188046912460 ICCID:898602A51314F1298017VERSION:MV930G_V2.0.2 BUILD:OCT 192016 16:31:00

Parameter Inquiry

|

PARAM#

| Device Reply Example： ID:9301074948 IMEI:861157040411486 APN:CMNET IP:47.254.77.28:7700 TIMER:10,180 SPEEDLIMIT: 120km/h ANGLERPT: 30’CENTER: 13428768257 SOS:13267052361,13488888888,13599999999 GMT:E8.00
Latitude&Longitude Inquiry| WHERE#| LAT:N23.02930,LON:E114.32180,COURSE:0.00,S PEED:0.00KM/H,DATETIME:2015-05-23 14:39:11
Map URL Inquiry| URL#| http://map.google.com/?q=22.557868,113.935090<0.0km/h 0.0> <2014-12-12 07:32:13> IMEI:354188047752402

Address Inquiry

|

POSITION#

| NOTE: Reply message’s language is determined by device’s language setting, if get position content failed, device will reply Google Map location link.

Status Inquiry

|

STATUS#

| BATTERY: XX% (Built-in Battery Power Percent)INTERNET: CLOSED (No Network)FAILED (Connecting Network or Failure)SUCCESS (Connected to Network）NET : NONE (No celluar Signal), HIGH / MED / LOW (Signal Strength) , 18(Signal value) GPS: CLOSED (GPS Module Closed); FIXED,N (Positioned and satellite number); UNFIX,0 (Not Positioned yet)SPEED: 30KM/HACC: ON / OFF (ACC on or off)RELAY: ON / OFF (Relay on or off)POWER: CONNECTED / DISCONNECTED1(P2o.5wVe(rVCeohnicnleecbtaetdteorry Dvioslctoagnen) ected), SENSOR: ON/OFF (S sor on or off), LEVEL: 3 (Sensitivity level 1-9) STATE: ARM (Arm or Disarm)

Alarms Parameters

|

ALARM#

| ID: 19172012644 (ID number of device)STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value);alarm waySHIFT: ON/OFF(alarm status); 300m(alarm value);alarm wayVIBRATE: ON/OFF(alarm status);3(sensitivity level);alarm wayACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way ; ;POWER DOWN: ON/OFF(alarm status);alarm way LOW VOLTAGE: ON/OFF(alarm status);alarm way NOTE: Alarm Ways: 0/1/2 ( 0 : SERVER only, 1: SMS+GPRS, 2 : GPRS+SMS+CALL )
Alarm Commands
Functions| Command Format| Explanation

Overspeed Alarm Setting

|

SPEED,A,B,M#

| Example: SPEED,ON,100,1# (When the speed of the tracker exceeds 100km/h it will send alarm message via SMS and server)A=ON/OFF, enable or cancel over speed alarm, default: OFFB=1～255(km/h), speed limit, default：100(km/h); M=0/1/2, way of alarm, 0 : Server only, 1: SMS+ Server, 2: SMS+ Server+ Call default：1.
SPEED,OFF#| CANCEL OVERSPEED ALARM OK

Vibration Alarm Setting

|

SENALM,A,M#

| Example: SENALM,ON,2# (Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered)A=ON/OFF, default: OFF;M=0/1/2, way of alarming, 0 : Serveronly, 1: SMS+ Server, 2 : SMS+Server+Call, default:2
SENALM,OFF#| CANEL VIBRATE ALARM OK

Shift Alarm Setting

|

SHIFT,A,B,M#

| Example: SHIFT,ON,300,1# ( Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle’s 300 meters’ shift will trigger the alarm, the alarm message will be sent via SMS and server )A=ON/OFF; default:ONB=Shift Distance (Range: 100-9999m)M=0/1/2; way of alarm, 0 : Server only, 1: SMS+Server, 2: Server+SMS+CALL, default:1
SHIFT,OFF#| CANCEL SHIFT ALARM OK

Auto Arm By ACC

| ACCARM,ON,M#| Example: ACCARM,ON,60# (Means when the engine turned to off status, the tracker will enter into arm status automatically after 60s)Arm Time: M=5-1800s, default: 60s
ACCARM,OFF#| Close auto arm function

ACC Status Change Alarm

|

ACCALM,A,B,M#

| Example: ACCALM,ON,2,2# (Means enable this alarm type, tracker will send alarm message via SMS, server and call when engine start and flameout)A=ON/OFF, Default: ON;B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACCON&OFF Alarm; Default:2M: 0/1/2 (way of alarm): 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call, Default:1;
ACCALM,OFF#| Cancel ACC alarm function

Power Disconnect Alarm

| PWRALM,A,M#| Example: PWRALM,ON,1# (Means when the external power disconnect the tracker will send alarm message via SMS and server)A=ON/OFF, default ON;M=0/1/2, ways of alarming, 0: Serveronly, 1: SMS+ Server, 2 : SMS+Server+Call, default:2；
PWRALM,OFF#| Close power disconnect alarm

Low Voltage Alarm Setting

|

LVALM,A,B,M#

| Example: LVALM,ON,11.2V,1# (Means once the external power voltage is less than 11.5v the tracker will send alarm message out via SMS and server)A=ON/OFF, default：ON;B=9-95 V, Low voltage threshold, can be a decimal, such as12.5 VM=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call,default:1
LVALM,OFF#| CANCEL LOW VOLTAGE ALARM OK

Vibration Alarm Setting

|

SENALM,A,M#

| Example: SENALM,ON,2# (Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered)A=ON/OFF, default: OFF;M=0/1/2, way of alarming, 0 : Serveronly, 1: SMS+Server, 2 : SMS+Server +Call, default:2
SENALM,OFF#| CANEL VIBRATE ALARM OK

Shift Alarm Setting

|

SHIFT,A,B,M#

| Example: SHIFT,ON,300,1# ( Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle’s 300 meters’ shift will trigger the alarm, the alarm message will be sent via SMS and server )A=ON/OFF; default:ONB=Shift Distance (Range: 100-9999m)M=0/1/2; way of alarm, 0 : Server only, 1: SMS+Server, 2: Server +SMS+ CALL, default:1
SHIFT,OFF#| CANCEL SHIFT ALARM OK

Auto Arm By ACC

| ACCARM,ON,M#| Example: ACCARM,ON,60# (Means when the engine turned to off status, the tracker will enter into arm status automatically after 60s)Arm Time: M=5-1800s, default: 60s
ACCARM,OFF#| Close auto arm function

ACC Status Change Alarm

|

ACCALM,A,B,M#

| Example: ACCALM,ON,2,2# (Means enable this alarm type, tracker will send alarm message via SMS, server and call when engine start and flameout)A=ON/OFF, Default: ON;B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACCON&OFF Alarm; Default:2M: 0/1/2 (way of alarm): 0 : Server only, 1: SMS+ Server, 2: SMS+ Server+ Call, Default:1;
ACCALM,OFF#| Cancel ACC alarm function

Power Disconnect Alarm

| PWRALM,A,M#| Example: PWRALM,ON,1# (Means when the external power disconnect the tracker will send alarm message via SMS and server)A=ON/OFF, default ON;M=0/1/2, ways of alarming, 0: Server only, 1: SMS+ Server, 2 : SMS+ Server+ Call, default: 2；
PWRALM,OFF#| Close power disconnect alarm

Low Voltage Alarm Setting

|

LVALM,A,B,M#

| Example: LVALM,ON,11.2V,1# (Means once the external power voltage is less than 11.5v the tracker will send alarm message out via SMS and server)A=ON/OFF, default ：ON;B=9-95 V, Low voltage threshold, can be a decimal, such as12.5 VM=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call,default:1
LVALM,OFF#| CANCEL LOW VOLTAGE ALARM OK

Any Questions?

E-mail: support@micodus.com
Skype: MiCODUS

Download the APP

Search “MiCODUS” in iOS APP store or Google Play Store, or just scan the QR code as below to download MiCODUS APP:

References

• Spionlink - SIM Card Service | Prepaid Data Plan | GPS Tracker Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>