MiCODUS MV66 2G Mini OBD II GNSS Tracker User Manual

: October 30, 2023
: MiCODUS

Table of Contents

MiCODUS MV66 2G Mini OBD II GNSS Tracker
Product Information: MiCODUS Tracker
Main Features
Product Usage Instructions
Specifications
Working Parameters
GNSS Specifications

MiCODUS MV66 2G Mini OBD II GNSS Tracker

Product Information: MiCODUS Tracker

Main Features

Compact Size
Plug & Play
Real-time Tracking
Historical Route Overspeed Playback
Alarm ON / OFF
Engine On/ OFF Alarm
Shift Alarm
Vibration Alarm
Geo-fence
Plug Out Alarm
Low Voltage Voice Monitor Alarm

Product Usage Instructions

Charge the MiCODUS Tracker backup battery before use.
Insert a SIM card into the tracker.
Install the tracker in your vehicle.
Turn on the tracker by pressing the ON/OFF button.
The tracker will start real-time tracking and record historical routes.
To set up alarms, use the following commands:
- Engine On/Off Alarm: #EOA#ON# or #EOA#OFF#
- Shift Alarm: #SA#ON# or #SA#OFF#
- Vibration Alarm: #VA#ON# or #VA#OFF#
- Geo-fence Alarm: #GF#ON# or #GF#OFF#
- Plug Out Alarm: #POA#ON# or #POA#OFF#
- Low Voltage Voice Monitor Alarm: #LVMA#ON# or #LVMA#OFF#
To view historical routes and overspeed playback, use the following command: #HIS#password#

Note : Replace ‘password’ in the above command with your tracker password.

Specifications

Device Information

Model: MV66
Weight: N/A
Dimensions: N/A
Backup Battery: Yes

Working Parameters

Working Voltage: N/A
Working Current: N/A
Sleep Current: N/A
Working Temperature: N/A
Working Humidity: N/A

Communication Module

Cellular Specifications: N/A
SIM Card: Yes
Celluar Antenna: Yes
Working Frequencies: N/A

GNSS Specifications

Satellite Channels: N/A
GPS Frequencies: Yes
BDS Frequencies: Yes
Hot/warm/cold Start: Yes
Tracking sensitivity: Yes
GNSS Antenna: Yes
Positioning Type: N/A
Accurancy GNSS Accuracy: <10M @ Open Sky
LBS Accuracy: 100-2000m
(Depend on density of base stations)

Activate Device

First Step： Prepare and Install SIM Card

If using your local SIM card, please make sure the SIM card already enabled SMS, internet data traffic, call and caller ID displaying functions;
If use our spionlink SIM card, then please recharge it via this website www.spionlink.com to get data plan firstly.
LED| Event| State
---|---|---

POWER LED (RED)

GPS LED (BLUE)

| GPS is in fixing| Flash every 1 second
GPS has fixed| Solid

ALL LED

| Device is working but stopped more than 5min| ****

ALL LED TURN OFF

Device has not been turn on
Device ran out of battery

Second Step: Configure APN

Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below:

SMS Command Format	Reply	Example	Note
apn,apn content, apnuser,apnpasswd#	apn ok	apn,orange, orange,orange#	If

there has APN user and APN apnpassword, then please use this command for configuration
apn,apn content#| apn ok| apn,internet#| If there doesn’t have APN user and APN password, then please use this command for configuration

Note : The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply “SET APN ok” but it will can’t get online!

Package Content

MV66 OBD Tracker x 1
User Guide x 1
Packing Box x 1
OBD Extension Cable（optional） x 1

Functions Explanation

Voice Monitor
Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below: Second Step: Configure APN
Step 1: Set up a center number for the device: CENTER,A,CENTER NUMBER#
For example, if your cellphone number is 008613655559999, then you can set up the center number like this: CENTER,A,+8613655559999# Note : Please add country code as prefix with your cellphone number!
Step 2: Use the center number to set up a number for the tracker to call back: MONITOR,number for monitor#
For example: MONITOR,+8613366668888# The tracker will make a call to this number +8613366668888 and this number can pick up the call to monitor the voice around it.
Set Data Upload Interval
TIMER,T1,T2#
T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10;
T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, 0 means no upload, default is 10;
For example: TIMER,10,3600# This command means the tracker will upload every 10 seconds when it engine is on, and every 3600 seconds when engine is off.
Vibration Alarm
Step 1 : Set up a center number for the device: CENTER,A,CENTER NUMBER#
For example: if you want to set up this number as center number:+8613366668888, the command should be sent like this: CENTER,A,+8613366668888#
Note : Please put the country code as prefix with the center number
Step 2: Set up SOS contact numbers:
SOS,A,SOS1,SOS2,SOS3#
For example: SOS,A,+8613366667777,+8613366667778,+8613366667779#
Note : You can set up 3 SOS alarm numbers for the device at the same time.
Step 3: Set up the vibration alarm way: SENALM,A,M#
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming, 0 : Server only, 1: SMS+Server,
2 : SMS+Server+Call, default:2
For example: SENALM,ON,1#
This means the vibration alarm message will be sent out via server and SMS

Installation Recomendation

Area A: VW、Ford、 Toyota 、Hyundai 、Citroen、BMW、 etc./Most cars.
Area B: Honda,Lexus,etc.
Area C: Dongfeng Citronen,etc.
Area D/E: A few cars…

Trouble shooting

Type	Use

Unable to connect to tracking platform

| Check the APN and settings.

Check whrther the data service of SIM card is enabled. Check the balance of SIM card.

Tracker shows offline

| Check whether external power is still connected. Check if the vehicle entered netword blind area. Check the balance of SIM card.

Unable to locate

| Make sure the top side facing upward without metallic things shielded.

Make sure it’s not in area with no satellite coverage.

Location drift

| In area with poor GNSS signal (tall building around or basement), drifting may happen.

Check whether vibration happens around to trigger the accelerator.

No command reply

| Make sure command format is correct. Vehicle may be in network blind area.

Make sure SIM card is well inserted and has SMS servi.

Full SMS Commands List

Query Commands

Functions	Command Format	Explanation

Version Inquiry

|

VERSION#

|

Device Reply Example: ID:7201074948 IMEI:354188046912460 ICCID:898602A51314F1298017 VERSION:MV66_V2.0.2 BUILD:OCT 19 2016 16:31:00

Map URL Inquiry

|

URL#

| http://map.google.com/?q=22.557868,113. 935090 <0.0km/h 0.0> <2023-01-06

17:32:13> IMEI:354188047752402

Check IMEI

|

IMEI#

|

DEVICE IMEI No. : 354188046912458

Functions	Command Format	Explanation

Address Inquiry

|

POSITION#

| NOTE: Reply message’s language is determined by device’s language setting, if get position content failed, device will reply Google Map location link.

Parameter Inquiry

|

PARAM#

| ID: ID number of the tracker

IMEI: IMEI number of the

APN:APN name,APN user,APN password, IP:Domain name and port number or IP address, port pumber

TIMER:Moving upload interval; Static upload interval

SPEEDLIMIT: The overspeed threshold ANGLERPT: Data uploading angle CENTER: Center number of the tracker SOS: SOS1,SOS2,SOS3

GMT:Time zone

Status Inquiry

|

STATUS#

| GPRS: CLOSED (No Network) FAILED (Connecting Network or Failure) SUCCESS (Connected to Network） GSM: NONE (No celluar Signal), HIGH / MED/ LOW

(Signal Strength) , 18(Signal value)

GPS: CLOSED (GPS Module Closed); FIXED,N

(Positioned and satellite number); UNFIX,0 (Not Positioned yet) SPEED: 30KM/H

ACC: ON / OFF (ACC on or off)

POWER: CONNECTED / DISCONNECTED

(Power Connected or Disconnected), 12.5V (Vehicle battery voltage) SENSOR: ON/OFF (Sensor on or off), LEVEL: 3 (Sensitivity level 1-9) STATE: ARM (Arm or Disarm)

Alarms Parameters

|

ALARM#

| ID: 19172012644 (ID number of device)

STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value); alarm way

SHIFT: ON/OFF(alarm status); 300m(alarm value); alarm way

VIBRATE: ON/OFF(alarm status);3(sensitivity level); alarm way

ACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way ; POWER DOWN: ON/OFF(alarm status);alarm way LOW VOLTAGE: ON/OFF(alarm status);alarm way NOTE: Alarm Ways: Server Only, Server+SMS, Server+SMS+Call

Latitude&Longitude Inquiry

|

WHERE#

| LAT:N23.02930,LON:E114.32180,COURSE: 0.00,S PEED:0.00KM/H,DATETIME:

2023-01-06 17:39:11

Setting Commands

Functions	Command Format	Explanation
Change IMEI	IMEICHG, 354188046912460#	NEW IMEI No. : 354188046912460
Restore factory settings	FACTORY#	RESTORE FACTORY SETTINGS OK
Restart device	RESTART#	RESTARTING…1 MINUTE WILL BE OK

APN Setting

| APN,Network name [,name,password]#| APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password)

Server Setting

| If set with Domain Name: SERVER,1,Domain,Port#| SERVER,1,d.micodus.net,7700#
If set with IP: SERVER,0,IP,Port#| SERVER,0,47.254.77.28,7700#

Internet Traffic Switch

| TRAFFIC,ON#| OPEN TRAFFIC OK
TRAFFIC,OFF#| CLOSE TRAFFIC OK

Time Zone Setting

| GMT,Time zone orientation,Whole Time Zone [,Half Time Zone]#| GMT,E,8# (if no half time zone)

GMT,W,9,30# (if has half time zone)

NOTE: Parameter : E / W；0 ~ 12; 0/15/30/45

Set the angle upload

|

ANGLEREP,X,A,B#

| Example: ANGLEREP,ON,30,3# ( Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds)

X=ON/OFF, default: ON;

A=5～180 degrees, diversion angle degree, default： 30 degrees；

B=2～5 seconds, detecting time, default：3 seconds,

ANGLEREP,OFF#| CANCEL UPLOAD ANGLE OK

Mileage Statistics

|

MILEAGE,A,B#

| Example: MILEAGE,ON,5000# (Means the initial mileage value is 5000KM)

A=ON/OFF, On/Off mileage calculation, default: Off

B=0～999999，Mileage initial value , unit：km ;

default: 0, mileage return to zero

MIELEAGE#| Query current mileage

Add SOS Administrator Number

|

SOS,A,1st number, 2nd number,

3rd number#

| Set 3 numbers at a time:

SOS,A,13800138000,1380013800 1,13800138002#

Set the first numberseparately:

SOS,A,13800138000#

Set the second number separately:

SOS,A,,13800138001#

Means to set 3rd number separately:

SOS,A,,,13800138002#

Functions	Command Format	Explanation

Delete SOS Administrator Number

|

SOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3#

| Directly delete the number:

SOS,D,13800138000#

Delete 1st number: SOS,D,1#

Delete 2nd number: SOS,D,2#

Delete the 2nd and 3rd number: SOS,D,2,3#

Add

Center Number

|

CENTER,A,center number#

| CENTER,A,+8613800138000#

NOTE: Please remember to add the country code as prefix with the cellphone number!

Delete Center Number|

CENTER,D#

|

DEL CENTER OK

Data Upload Time Interval

|

TIMER,T1,T2#

| Example: TIMER,5,3600#

T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10;

T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;

Heartbeat Packet Upload

|

HBT,time#

| Example: HBT,3# ( Means the tracker will send hearbeat data package to server very 3min to keep the network connected )

Time: 1-60min, default 3min

Sensor Sensitivity

|

LEVEL,A#

| Example: SENLEVEL,4# ( Means shake sensor level is set to 4 )

A=1-9

NOTE: 1-9 is from week to strong vibration

Arm manually

|

DISARM#

|

Set the device into arm mode

Disarm manually| ARM#| Set the device out of arm mode

Auto Arm By ACC

|

ACCARM,ON,M#

| Example: ACCARM,ON,60# (Means the tracker will enter into arm status automatically when the ACC off more than 60 seconds)

Arm Time: M=5-1800s, default: 60s

ACCARM,OFF#| Close auto arm function

Voice Monitor

|

MONITOR,

+8613428768257#

| Example: MONITOR,+8613366669999#

(Means the tracker will make call to this number

+8613366669999,then this number +8613366669999 can pick up the call to monitor the voice)

N: Number for Voice Monitoring

NOTE: 1.Please send this monitor command via the center number; 2. Any number can be set up to monitor the voice, the tracker will make a call to the number

N and it will can pick up the call to monitor voice

Alarm Setting Commands

Functions	Command Format	Explanation

Overspeed Alarm Setting

|

SPEED,A,B,M#

| Example: SPEED,ON,120,1# ( Means the speed limit is 120km/h and the alarm way is via SMS and Server ) A=ON/OFF, open or close over speed alarm,

default: OFF

B=1～255(km/h), speed limit, default：100(km/h);

M=0/1/2, way of alarm, 0 : SERVER only, 1: SERVER+

SMS, 2: SERVER+SMS+CALL; default: 1

Vibration Alarm Setting

|

SENALM,A,M#

| Example: SENALM,ON,2# ( Means the vibration alarm already been enabled and the alarm message will be sent via Server, SMS and Call )

A=ON/OFF, default: OFF;

M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1

SENALM,OFF#| CANEL VIBRATE ALARM OK

Shift Alarm Setting

|

SHIFT,A,B,M#

| Example: SHIFT,ON,100,1# ( Means Setting 100 meters shift alarm range, when the ignition turned off, vehicle’s 100 meters’ shift will trigger the alarm.) A=ON/OFF; default:ON

B=Shift Distance (Range: 100-9999m)

M=0/1/2; way of alarm, 0 : GPRS only,

1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1

SHIFT,OFF#| CANCEL SHIFT ALARM OK

ACC Status Change Alarm

|

ACCALM,A,B,M#

| Example: ACCALM,ON,0,2# (Means the tracker will send alarm message out via Server, SMS and Call when the engine is start)

A=ON/OFF, Default: ON;

B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF

Alarm; 2: ACC ON&OFF Alarm; Default:2

M: 0/1/2 (way of alarm): 0 : Server only,