MiCODUS MV501G Car GPS Tracker User Manual

: October 30, 2023
: MiCODUS

Table of Contents

MiCODUS MV501G Car GPS Tracker
Package Contents
Usage Instructions
Main Features
Specifications
Wiring diagram
Activate Device
Functions Explanation
Installation Recomendation
Troubleshooting
Full SMS Commands List
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MiCODUS MV501G Car GPS Tracker

MiCODUS Tracker

The MiCODUS Tracker is a GPS tracking device that comes with a range of features to ensure the safety of your vehicle. The device supports 4G+2G connectivity for real-time tracking and historical route playback. It also has a 1000mAh battery and supports cut-off fuel/resume fuel, SOS, voice monitor, geo-fence, overspeed alarm, and vibration alarm.

Specifications

The MV501G model weighs 150g and has dimensions of 107mm(L) 51mm(W) 20mm(H). The device has a working voltage of 9-36V DC and supports a normal SIM card. It has a GPS antenna and supports cold start and hot start. The device has a tracking sensitivity of 64 and position accuracy of 5-10m. The device works in a temperature range of -20°C to 70°C and humidity range of 5% to 95%. The device supports GNSS positioning type.

Package Contents

GPS Main Unit MV501G x 1
Function Cable x 1
Microphone Cable x 1
SOS Button Cable x 1
Relay x 1
User Guide x 1
Temperature Sensor (Optional) x 1
Fuel Sensor (Optional) x 1
Camera (Optional) x 1
Genuine Packing Box x 1

Usage Instructions

Activate Device

To activate the device, install the SIM card in the correct direction. Use the SMS command format to set the correct APN name and configure the APN. Take the device to a good signal place for operation.

Voice Monitor

To use the voice monitor feature, set the center number using the SMS command: CENTER,A,center number#. Switch the tracker to voice monitor mode by using the SMS command: MONITOR#. Dial the SIM number of the tracker from the center number to remotely monitor the voice around it.

Vibration Alert

The vibration alert function works only under stationary status.
To use this feature, configure SOS numbers for the tracker using the SMS command: SOS,A,1st number,2nd number,3rd number#. Enable the device to enter into arm mode by using the SMS command: ARM#.

Main Features

Specifications

Device Information

| Model| MV501G
---|---|---
Weight| 150g
Dimensions| 107mm(L) 51mm(W) 20mm(H)
Charging Time| Around 7 hours
Battery Working Time| Tracking Mode:1- 2 Days

Working Parameters

Cellular Specifications

| Working Frequency| 4G LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66

2G GSM/GPRS/EDGE: 850/900/1800/1900MHz

SIM Card| Micro SIM Card
Cellular Antenna| Built-in

GNSS Specifications

Wiring diagram

Activate Device

LED	Event	State

POWER LED (RED)

ALL LED

| Device is working but stopped more than 5min|

ALL LED TURN OFF

Device has not been turn on
Device ran out of battery

Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below:

SMS Command

Format

| Reply| Example| Note
---|---|---|---

APN,ApnName,User, Password#

|

SET APN OK

|

APN,orange, orange,orange#

|

If the SIM card has APN user and APN password, then use this command.

APN,ApnName#

|

SET APN OK

|

APN,internet#

| If the SIM card operator doesn’t have APN user and APN password, then please use this command.

Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply “SET APN ok” but it will can’t get online!

Functions Explanation

Please follow with the quick user guide carefully!

Voice Monitor:

Set center number by this sms command:
CENTER,A,center number
Switch the tracker to voice monitor mode by this sms command:MONITOR#
Dial the sim number of the tracker from the center number, then the tracker will pick up the call automatically and you will can remote monitor the voice around it.

Vibration Alert:
This vibration alert function just work under stationary status. How to use this function:

Configure SOS numbers for the tracker by this sms command: SOS,A,1st number,2nd number,3rd number#
3 SOS numbers supports at the most
Enable the device to enter into arm mode by this sms command: ARM#
Conifgure the alarm ways by this sms command:
SENALM,[A][,M]#
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming,
0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1
Keep the device under stationary status more than 5min to let it enter into sleep arm mode;
Vibrate the device then the tracker will send the vibration alarm messages

Cut Off Fuel/Resume Fuel

Set center number by this sms command: CENTER,A,center number#
Send this sms command from the center number:
RELAY,A#
A=0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately; 2: Cut Off Fuel Safely)

Enable SOS Emergency Call

Set sos alarm numbers via this sms command: SOS,A,1st number,2nd number,3rd number#
Long press the SOS panic button 3 seconds then the emergency call will be made to the sos numbers, it will dial the numbers by turn till it is picked up

Installation Recomendation

The decice should face up to the sky.
Metal therma barrier of heating layer of the windshield affects the signal.

Troubleshooting

Type	Use

Unable to connect to

tracking platform

| Check the APN and settings.

Check whrther the data service of SIM card is enabled. Check the balance of SIM card.

Tracker shows offline

| Check whether external power is still connected. Check if the vehicle entered netword blind area. Check the balance of SIM card.

Unable to locate

| Make sure the top side facing upward without metallic things shielded.

Make sure it’s not in area with no satellite coverage.

Location drift

| In area with poor GNSS signal (tall building around or basement), drifting may happen.

Check whether vibration happens around to trigger the

accelerator.

No command reply

| Make sure command format is correct.

Vehicle may be in network blind area.

Make sure SIM card is well inserted and has SMS servi.

Full SMS Commands List

Functions	Command Format	Explanation

APN Setting

|

APN,Network name[,name,password]#

| APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password)

Server Setting

| If set with Domain Name: SERVER,1, Domain,Port#|

SERVER,1,d.micodus.net,7700#

If set with IP: SERVER,0,IP,Port#| SERVER,0,47.254.77.28,7700#

Revise the instruction password

|

PASSWORD,[A],[B]#

| A=old password, six digitals, digital range: 0-9,

default：000000;

B=new password, six digitals, digital range: 0-9

Check IMEI| IMEI#|
Restore factory settings|

FACTORY#

|
Restart device| RESET#|

Set The Angle Upload

|

ANGLEREP,[X][,A][,B]#

| X=ON/OFF, default：ON; A=5～180 degrees,

diversion angle

degree, default：30 degrees；B=2～5 seconds, detecting time, default：3 seconds,

---|---|---
ANGLEREP,OFF#|

Mileage Statistics

|

MILEAGE,[A],[B]#

|

A=ON/OFF, On/Off mileage calculation, default: Off B=0～999999，Mileage initial value , unit：km ; default: 0, mileage return to zero

MIELEAGE#

|

Query current mileage

Add SOS Administrator

Number

|

SOS,A,1st number,2 nd number,

3rd number#

|

Set 3 numbers at a time: SOS,A,13800138000,1380013800 1,13800138002#

Set the first numberseparately: SOS,A,13800138000#

Set the second number separately: SOS,A,,13800138001#

Means to set 3rd number separately: SOS,A,,,13800138002#

Delete SOS

Administrator Number

|

SOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3#

|

Directly delete the number: SOS,D,13800138000#

Delete 1st number:

SOS,D,1#

Delete 2nd number:

SOS,D,2#

Delete the 2nd and 3rd number: SOS,D,2,3#

Add Center Number

|

CENTER,A,center number#

| CENTER,A,13800138000#

NOTE: Center number is only used for cutting off power & oil, it can only be set by SOS Administrator when using this command by SMS.

Delete Center Number

|

CENTER,D#

|

Data Upload Time Interval

|

TIMER,T1,T2#

| T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;
Heartbeat Packet

Upload

|

HBT,time#

| HBT,3#

NOTE: Range :1-60min, default 3min.

Sensor Sensitivity

|

LEVEL,A#

| LEVEL,2#

NOTE: A：Sensitivity Level 1-9

(1-9 is from week to strong vibration)

Arm Manually

|

ARM#

|

Set the device into arm mode

Disarm manually

|

DISARM#

|

Set the device out of arm mode

---|---|---

Cut Off / Resume Fuel

|

RELAY,A#

|

A=1/2;

1: Enable relay immediately

2: Enable relay safely [STATE] ON/OFF

1. RELAY,1#

A is set to 1, the relay command will be executed

immediately;

2. RELAY,2#

A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.

RELAY,0#

|

Overspeed Alarm Setting

|

SPEED,[A][,B][,C]#

| A=ON/OFF, open or close over speed alarm, default：OFF B=1～255(km/h), speed limit, default：100(km/h);

C=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS, default:1.

SPEED,OFF#

|

Vibration Alarm

Setting

|

SENALM,[A][,M]#

|

A=ON/OFF, default: OFF; M=0/1/2, way of alarming,

0 :GPRS only, 1: SMS+GPRS,

2 : GPRS+SMS+phone call, default:2

SENALM,OFF#

|

Shift Alarm Setting

|

SHIFT,[A][,B][,M]#

| Example: SHIFT,ON,100,1# ( Means Setting 100 meters shift alarm range, when the ignition turned off, vehicle’s 100 meters’ shift will trigger the alarm. )

A=ON/OFF; default:ON

B=Shift Distance (Range: 100-9999m) M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+GPRS,

2: GPRS+SMS+CALL, default:1

SHIFT,OFF#

|

Auto Arm By ACC

|

ACCARM,ON,M#

|

Arm Time: M=5-1800s, default: 60s

ACCARM,OFF#

|