MEAN WELL LPV-20 series 20W Single Output Switching Power Supply Owner’s Manual
- June 15, 2024
- MEAN WELL
Table of Contents
MEAN WELL LPV-20 series 20W Single Output Switching Power Supply
Features
- Constant voltage design
- Universal AC input / Full range
- Withstand 300VAC surge input for 5 seconds
- Protections: Short circuit / Over load / Over voltage
- Cooling by free air convection
- Small and compact size
- Fully encapsulated with IP67 level (Note.7)
- Fully isolated plastic case
- Class II power unit, no FG
- Class 2 power unit
- Pass LPS
- Suitable for LED related fixture or appliance (such as LED Decoration or Advertisement devices)(Note. 11)
- 100% full load burn-in test
- Low cost, high reliability
- 2 years warranty
GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx
SPECIFICATION
| MODEL | LPV-20-5 | LPV-20-12 | LPV-20-15 | LPV-20-24 |
|---|---|---|---|---|
| OUTPUT | DC VOLTAGE | 5V | 12V | 15V |
| RATED CURRENT | 3A | 1.67A | 1.33A | 0.84A |
| CURRENT RANGE | 0 ~ 3A | 0 ~ 1.67A | 0 ~ 1.33A | 0 ~ 0.84A |
| RATED POWER | 15W | 20W | 20W | 20.2W |
| RIPPLE & NOISE (max.) **Note.2** | 80mVp-p | 120mVp-p | 120mVp-p | 150mVp-p |
| VOLTAGE TOLERANCE Note.3 | ±5.0% | |||
| LINE REGULATION | ±1.0% | |||
| LOAD REGULATION | ±2.0% | |||
| SETUP, RISE TIME | Note.6 | 500ms, 20ms / 230VAC 500ms, 20ms / |
115VAC at full load
HOLD UP TIME (Typ.)| 50ms/230VAC 16ms/115VAC at full load
INPUT| VOLTAGE RANGE| Note.4| 90 ~ 264VAC 127 ~
370VDC
FREQUENCY RANGE| 47 ~ 63Hz
EFFICIENCY (Typ.)| 77%| 81%| 83%| 83%
AC CURRENT (Typ.)| 0.55A/115VAC 0.35A/230VAC
INRUSH CURRENT(Typ.)| COLD START 70A(twidth=215μs measured at 50% Ipeak)
at 230VAC
MAX. No. of PSUs on 16A CIRCUIT BREAKER| 8 units (circuit breaker of
type B) / 14 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| 0.25mA / 240VAC
PROTECTION| OVER LOAD| 110 ~ 150% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is
removed
OVER VOLTAGE| 5.75 ~ 6.75V| 13.8 ~ 16V| 17.5 ~ 21V| 28 ~ 32V
Protection type : Shut off o/p voltage, clamping by zener diode
ENVIRONMENT| WORKING TEMP.| -30 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY| 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 50℃)
VIBRATION| 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X,
Y, Z axes
SAFETY & EMC| SAFETY STANDARDS| Ul879, UL1310, CSA C22.2 No.
207-M89,CAN/CSA C22.2 No. 223-M91,IEC/BS EN/EN 62368-1, IS
15885(Part2/Sec13)(NOTE 12), EAC TP TC 004,IP67 approved
WITHSTAND VOLTAGE| I/P-O/P:3KVAC
ISOLATION RESISTANCE| I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55032 (CISPR32) Class B, BS
EN/EN61000-3-2 Class A, BS EN/EN61000-3-3,EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS
EN/EN55035, light industry level, EAC TP TC 020
OTHERS| MTBF| 6025.8K hrs min. Telcordia SR-332 (Bellcore) ;
786.5Khrs min.| MIL-HDBK-217F (25℃)|
DIMENSION| 1183526mm (LWH)
PACKING| 0.22Kg; 60pcs/14.2Kg/0.72CUFT
NOTE| 1. All parameters NOT specially mentioned are measured at 230VAC
input, rated load and 25°C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted
pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load
regulation.
4. Derating may be needed under low input voltage. Please check the static
characteristics for more details.
5. The power supply is considered as a component that will be operated in
combination with final equipment. Since EMC performance will be affected by
the
complete installation, the final equipment manufacturers must re-qualify EMC
Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Turning ON/OFF the
power supply may lead to increase of the set up time.
7. Suitable for indoor use or outdoor use without direct sunlight exposure.
Please avoid immerse in the water over 30 minute.
8. The ambient temperature derating of 3.5°C/1000m with fanless models and of
5°C/1000m with fan models for operating altitude higher than 2000m(6500ft).
9. Products sourced from the Americas regions may not have the TUV/BIS/CCC
logo. Please contact your MEAN WELL sales for more information.
10. For any application note and IP water proof function installation
caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
11. This product is not intended for LED lighting luminaire applications in
the EU.(In the EU the LPF/NPF/XLG series are recommended.)
12. Products sourced from the China regions may not have the BIS logo, please
contact your MEAN WELL sales for more information.
https://www.meanwell.com/serviceDisclaimer.aspx
Mechanical Specification
Recommend Mounting Direction
Block Diagram
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>