saxby lighting 80497 Extrusion RigelSLIM Surface Instruction Manual
- May 15, 2024
- saxby lighting
Table of Contents
saxby lighting 80497 Extrusion RigelSLIM Surface Instruction Manual
EXTRUSION
80497, 80498, 80499, 80500, 80501, 94946, 94947, 94948, 94949 97732, 97734, 97735, 97736, 97737, 97738, 97739, 102665, 102666, 102667, 102668, 108286, 108287, 107409
Surface
Recessed
Bendable
Corner
Plaster-in
Thank you for purchasing this accessory. Please read the instruction carefully
before use to ensure safe and satisfactory operation of this product.
Please retain these instruction for future reference.
Specification
Dimensions
Surface
- 80497: 2000mm x 17mm x 9mm
- 94946: 2000mm x 17mm x 9mm
- 97734: 2000mm x 17mm x 9mm
- 97735: 2000mm x 23.5mm x 11.2mm
- 80498: 2000mm x 16.5mm x 13.5mm
- 97738: 2000mm x 23.5mm x 21.5mm
Recessed
- 94947: 2000mm x 21.7mm x 6mm
- 97736: 2000mm x 30.7mm x 11.2mm
- 97739: 2000mm x 30.0mm x 21.5mm
- 80499: 2000mm x 23.1mm x 13.4mm
- 108286: 2000mm x 23.1mm x 13.4mm
- 102666: 2000mm x 21mm x 13.5mm
Bendable
- 97732: 2000mm x 18mm x 5mm
Corner
- 80501: 2000mm x 16mm x 16mm
- 108287: 2000mm x 16mm x 16mm
- 97737: 2000mm x 30mm x 30mm
- 102668: 2000mm x 61mm x 61mm
Plaster-in –
- 80500: 2000mm x 56.9mm x 15.4mm
- 94948: 2000mm x 64mm x 14mm
- 94949: 2000mm x 100mm x 19.6mm
- 102665: 2000mm x 100mm x 19.6mm
- 102667: 2000mm x 95mm x 40mm
Installation for Surface / Recessed / Bendable / Corner
- Choose an ideal place to mount the profile.
- Remove the 4 brackets from the fixing pack.
- Using the brackets as templates, mark and drill the position of the fixing holes
- Ensure the mounting structure is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes.
- Attach both brackets to the chosen mounting surface using the plastic plugs and screws (not supplied) according to the following installation diagram.
- Remove the backing off of the chosen LED module strip and stick down inside the aluminium profile.
- Attach diffuser to the profile, sliding into the profile grooves.
- Place end caps onto the ends of the fitting.
- Push profile onto the brackets to secure.
- Your fitting is now ready for use
Product images may vary
Installation for Plaster-in
- Using the aluminium profile as templates, mark and drill the position of the fixing holes.
- Ensure the mounting structure is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes.
- Remove the backing off of the chosen LED module strip and stick down inside the aluminium profile.
- Attach diffuser to the profile, sliding into the profile grooves.
- Place end caps onto the ends of the fitting.
- Push the aluminum profile into the existing groove
- Then use the plastic plugs and screws (not supplied) to fix the aluminum profile to the wall.
- Cemented the sides of the aluminum profile
Product images may vary
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing
lightbulbs, or cleaning.
V5 18/05/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg