saxby lighting 103844 Arezzo Track Head Spotlight Instruction Manual

: October 30, 2023
: saxby lighting

Table of Contents

saxby lighting 103844 Arezzo Track Head Spotlight
Safety Warning
Layout
Installation
Connection
Wiring
Fitting Units
Technical data
Care and Safety
Contact Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 103844 Arezzo Track Head Spotlight

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.

Safety Warning

This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
Only to be installed outside arms reach.
Always use the correct type and wattage bulb. Exceeding the bulb wattage will damage the product.
This track is suitable for dimming. But the fittings with low voltage lamps are not suitable for dimming. Care must be taken to only use the same type of fitting that is able to be dimmed, and the dimmer wattage must not be exceeded.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

This track system can be extended to a variety of different configurations using accessories such as left bends, right bends, T junctions, X junctions, and flexible joints.

Track Accessory:

Products:

Installation

Existing fittings must be completely removed before the installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note the power at the fuse board and the luminaire must be switched off before installation or maintenance.

Plan the track layout and decide on accessories needed before fixing anything to the ceiling.
The maximum power per run of the track is 1 KW (1 OOOW).
Ensure the ceiling is capable of holding the weight of the track and products Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
Mark the first hole position and fit the screw in the position as shown.
Feed the screw through the keyhole slot, and slide into position. Mark the position of the second hole.
Locate the track and fit the second screw into position.
If fitting accessories, remove the end cap and push them firmly home.
Fit extra lengths of the track as required.

Connection

The track accessories are provided with earth connection points on both sides.
When offering the accessory to the track, verify which tab needs to be removed. (See left-hand diagram).
To remove the tab, grasp firmly with a pair of pliers and lever back.
The tab should snap cleanly off. (See right-hand diagram).
Locate the accessory in the track and push home.

Wiring

Undo the screw and remove the cover from the live end. Push out the desired cable access point. lndentify the correct cable from the supply and pull through.
Connect the supply wires to the terminal block, opposite the corresponding wires from the fitting. The central connector can also be wired in this way.
Refit the cover onto the live end taking care not to trap the cable.

Check that

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Fitting Units

Locate the product in the track with the connections in the slot.
There is a rotary switch on the track head. The fitting will be turned on when the rotary switch is in the ON position, and when it is turned 90° the fitting will be OFF.
Replace the fuse or circuit breaker and switch it on. Your light is now ready for use.

Technical data

Supply Voltage: 220-240 V-, 50 Hz
Bulb Type:
- 103844, 103845, 103846, 1 x Max. 35W GU1 O (required)
- 103847, 103848, 103849, 1 x Max. 7W LED GU10 (required)
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1, and must be connected to the earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
Always disconnect the product from the mains for at least 10 minutes allowing it to cool down before any maintenance or adjustment.
For your safety, always switch off the power supply before cleaning.