MiCODUS MV710G GPS Vehicle Tracker User Manual

MiCODUS MV710G GPS Vehicle Tracker

Product Information

• Specifications
  • Model: MV710G
  • Weight: 40g
  • Dimensions: 79mm(L)33mm(W)16mm(H)
  • Battery: Built-in 60 mAh 3.7V polymer battery
  • Working Voltage: 9-95V DC
  • Working Current: 12V/average 35mA
  • Sleep Current: 12V/average 10mA
  • Working Temperature: -20°C to 75°C
  • Working Humidity: 10%-85% RH non-condensing
  • SIM Card: Micro SIM
  • Cellular Antenna: Built-in, FPC
• Cellular Specifications:
  • GSM/2G: 850/900/1800/1900MHz
  • LTE/4G: LTE-FDD:B1/B2/B3/B4/B5/B7/B8/B28/B66
• GNSS Specifications:
  • GPS+BDS
  • GPS Frequency: BDS Frequency
  • Sensitivity: -162 dBm
  • Satellite Channels Hot/Cold Start: 32

Product Usage Instructions

• Setting up the MiCODUS Tracker
  • To set up your new MiCODUS Tracker, follow these steps:
  • Find a suitable location in your vehicle to place the tracker. Make sure it has access to the GPS and cellular signals.
  • Insert a micro SIM card into the tracker.
  • Connect the tracker to the power source with a voltage range of 9-95V DC.
  • Turn on the tracker using the ON/OFF switch.
  • Download and install the MiCODUS Tracker mobile app on your iOS or Android device.
  • Launch the app and create an account if you don’t have one already.
  • Follow the app’s instructions to pair the tracker with your account.
• Main Features
  • The MiCODUS Tracker offers the following main features:
  • 4G LTE+ 2G GSM connectivity for reliable communication.
  • ACC status detection to monitor the vehicle’s ignition status.
  • GPS+BDS for accurate positioning.
  • Remotely cut off and resume fuel tracking.
  • Historical route playback to review past journeys.
  • Vibration alarm for unauthorized movement or towing.
  • Alarm notifications for various events such as power failure, low battery voltage, engine on/off, and geo-fence breaches.
  • Overspeed alarm to alert you when the vehicle exceeds a preset speed limit.
  • Lifetime free iOS and Android tracking platform for real-time monitoring.
• Frequently Asked Questions (FAQ)
  • Q: How long does the battery last?
  • A: The MiCODUS Tracker has a built-in 60mAh polymer battery. The battery life will depend on the usage and settings, but it is recommended to connect the tracker to a power source for continuous operation.
  • Q: Can I use any SIM card with the tracker?
  • A: The tracker requires a micro SIM card for cellular connectivity. Make sure to use a compatible micro SIM card from a supported network provider.
  • Q: How do I view the historical route playback?
  • A: Launch the MiCODUS Tracker mobile app and navigate to the historical route playback section. Select the desired date and time range to view the recorded route on the map.
  • Q: What is the working temperature range of the tracker?
  • A: The MiCODUS Tracker is designed to operate within a temperature range of -20°C to 75°C. Avoid exposing the tracker to extreme temperatures outside this range.

Main Features

Specifications

Working Frequency

| GSM/2G : 850/900/1800/1900MHz
LTE/4G: LTE-FDD:B1/B2/B3/B4/B5/B7/B8/B28/B66

GNSS Specifications

| GNSS| GPS+BDS
GPS Frequency| L1: 1575.42±1.023MHz
BDS Frequency| B1:1561.098±2.046MHz
Sensitivity| -162 dBm
Satellite Channels| 32
Hot/Cold Start| <1s，<32s @ Open Sky
Positioning Antenna| Built-in ceramic dielectric antenna, 18184mm
Accuracy| <10m（1σ）
External Interface| ACC Detection| 1
Cut Off Fuel/Power| Standard
SOS（optional）| 1
Open door Alarm (optional)| 1
Microphone| 1

How to manage

How to manage the tracker to get online?

Step 1: SIM card requirements

Please get a suitable SIM card from your local place. The SIM card must meet below points:

• It must be compatible with the 4G LTE or 2G GSM network
• Please enable SMS, call, and internet data traffic of the SIM card
• Remove the PIN code
• Enable the caller ID display feature
• Use a size SIM card for the tracker
• Please inquire with the SIM card provider for the exact correct APN information

Step 2: SIM card installation

Step 3: Wiring

NOTE: After installing the SIM card correctly, it is very important to connect the tracker with external power no less than 12V for power supply before operation!

Step 4 Configure APN

Please get the exact correct APN name from the local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:

the SIM card has an APN user and APN password, then use this command.
APN,ApnName#|

SET APN OK

| APN,internet#| If the SIM card operator doesn’t have an APN user and APN password, then please use this command.

Note: The APN information is very important, it must be 100% correct to match with the sim card of the tracker, if you configured the wrong APN, the tracker also will reply “SET APN ok” but it will can’t get online!

Step 5 Indicator status description

ALL LED

| Device is working but stopped more than 5min|

ALL LED TURN OFF

Device has not been turn on
Device ran out of battery

Package Content

• GPS Main Unit x 1
• Function Cable x 1
• User Guide x 1
• Genuine Packing Box x 1

Functions Explanation

• a. Cut Off Fuel/Resume Fuel Set center number by this sms command: CENTER,A,center number#

  • Send this sms command from the center number: RELAY,A#
  • A= 0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately; 2: Cut Off Fuel Safely)
  • For example:

• b. Vibration Alert:

  • T his vibration alert function just work under stationary status. How to use this function:

  • Configure SOS numbers for the tracker by this sms command: SOS,A,1st number,2nd number,3rd number# 3 SOS numbers supports at the most

  • Enable the device to enter into arm mode by this sms command: ARM#

  • Conifgure the alarm ways by this sms command: SENALM,[A][,M]#

  • A= ON/OFF, default: OFF;

  • M= 0/1/2, way of alarming,

  • 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1

  • Keep the device under stationary status more than 5min to let it enter into sleep arm mode;
    Vibrate the device then the tracker will send the vibration alarm messages

  • For example:

• c. External Battery Low Voltage Alarm

  • Command format: LVALM,A,B,M#
  • A= ON/OFF, default： ON;
  • B= 9-95V (voltage alarm threshold), default: 11.1v
  • M= 0/1/2, way of alarming, 0: Server only,
  • 1: SMS+Server, 2: SMS+Server+Call, default:1；
  • For example: LVA LM, ON,11.5,1#
  • This means once the external battery voltage is less than 11.5v the device will send an alarm message via server and SMS.
  • For example:

• d. Engine Start and Flameout Alarm

  • Command format: ACCALM,A,B,M#
  • A= ON/OFF, Default: ON;
  • B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC
  • ON &OFF Alarm; Default:2
  • M: 0/1/2 (way of alarm): 0: Server only,
  • 1: SMS+Server, 2: SMS+Server+Call, Default:1;
  • For example: ACCALM, ON,2,1#
  • This means once the device detects engine start and engine flameout it will send an alarm message via server and SMS.
  • For example:

Installation Recommendation

Troubleshooting

Check whether the data service of SIM card is enabled. Check the balance of SIM card.

Tracker shows offline

| Check whether external power is still connected. Check if the vehicle entered the network blind area. Check the balance of SIM card.

Unable to locate

| Make sure the top side facing upward without metallic things shielded.

Make sure it’s not in area with no satellite coverage.

Location drift

| In area with poor GNSS signal (tall building around or basement), drifting may happen.

Check whether vibration happens around to trigger the accelerator.

No command reply

| Make sure command format is correct. Vehicle may be in network blind area.

Make sure SIM card is well inserted and has SMS service.

Full SMS Commands List

Setting Commands

Functions| Command Format| Explanation

APN Setting

|

APN,Network name[,name, password]#

| APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password)

Server Setting

| If set with Domain Name: SERVER,1,Domain,Port#| SERVER,1,d.micodus.net,7700#
If set with IP: SERVER,0, IP,Port#| SERVER,0,47.254.77.28,7700#
Check IMEI| IMEI#| DEVICE IMEI No. : 0123456789
Change IMEI| IMEICHG,354188046912460#| NEW IMEI No. : 354188046912460
Restore factory settings| FACTORY#| RESTORE FACTORY SETTINGS OK
Restart device| RESTART#| RESTARTING…1 MINUTE WILL BE OK

Internet Traffic Switch

| TRAFFIC,ON#| OPEN TRAFFIC OK
TRAFFIC,OFF#| CLOSE TRAFFIC OK

Time Zone Setting

|

GMT,A,B,C#

| Example:GMT,E,8# (Means East +8 zone, no half time zone)

GMT,W,9,30# (Means West -9.5 zone, has half time zone)

A: E / W, E: East time zone, W: West time zone B: 0 ~ 12; whole time zone

C: 0/15/30/45, half time zone

Set the angle upload

|

ANGLEREP,X,A,B#

| Example: ANGLEREP,ON,30,3# ( Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds)

X=ON/OFF, default：ON;

A=5～180 degrees, diversion angle degree, default: 30 degrees；

B=2～5 seconds, detecting time, default: 3

seconds,

ANGLEREP,OFF#| CANCEL UPLOAD ANGLE OK

Mileage Statistics

|

MILEAGE,A,B#

| Example: MILEAGE,ON,5000# (Means enable the mileage statistics feature, the mileage initial value is 5000km)

A=ON/OFF, On/Off mileage calculation, default: Off B=0～999999，Mileage initial value , unit：km ;

default: 0, mileage return to zero

MIELEAGE#| Query current mileage

Add SOS Administrator Number

|

SOS,A,1st number,2nd number, 3rd number#

| Example:

Set 3 numbers at a time: SOS,A,13800138000,13800138001,13800138002#

Set the first numberseparately: SOS,A,13800138000#

Set the second number separately: SOS,A,,13800138001#

Means to set 3rd number separately:

SOS,A,,,13800138002#

---|---|---

Delete SOS Administrator Number

|

SOS,D,1st number,2nd number, 3rd number# or SOS,D,1,2,3#

| Example:

Directly delete the number: SOS,D,13800138000#

Delete 1st number: SOS,D,1#

Delete 2nd number: SOS,D,2#

Delete the 2nd and 3rd number: SOS,D,2,3#

Add Center Number

|

CENTER,A,center number#

| Example: CENTER,A,008613800138000# (Means

the tracker will just can be controlled by this number 008613800138000, 0086 is country code)

NOTE:

1. Please set up the center number with the country code as prefix!

2. After set up center number, the tracker will just can be controlled by center number, it will not reply commands from other numbers!

Delete Center Number

|

CENTER,D#

|

DEL CENTER OK

Data Upload Time Interval

|

TIMER,T1,T2#

| Example: TIMER,5,180# (Means the tracker will upload data every 5s when ACC is on and 180s when ACC is off)

T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;

Heartbeat Packet Upload

|

HBT,time#

| Example: HBT,3# (Means the tracker will send the heartbeat data package to server every 3 min for connection maintenance)

NOTE: Range :1-60min, default 3min.

Sensor Sensitivity

|

LEVEL,A#

| Example: LEVEL,2# (Means set up the shake sensor level to 2)

NOTE: A：Sensitivity Level 1-9 (1-9 is from week to strong vibration)

Arm manually| ARM#| Set the device into arm mode

Disarm manually

|

DISARM#

|

Set the device out of arm mode

Cut Off / Resume Fuel

|

RELAY,A#

| A=1/2;

1: Enable relay immediately 2: Enable relay safely

For Example:

1. RELAY,1#

A is set to 1, the relay command will be executed immediately.

2. RELAY,2#

A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.

---|---|---
RELAY,0#| RESUME FUEL OK
Inquiry Commands
Functions| Command Format| Explanation

Version Inquiry

|

VERSION#

| Device Reply Example: ID:9301074948 IMEI:354188046912460 ICCID:898602A51314F1298017

VERSION:MV930G_V2.0.2 BUILD:OCT 19

2016 16:31:00

Parameter Inquiry

|

PARAM#

| Device Reply Example： ID:9301074948 IMEI:861157040411486 APN:CMNET IP:47.254.77.28:7700 TIMER:10,180 SPEEDLIMIT: 120km/h ANGLERPT: 30′

CENTER: 13428768257 SOS:13267052361,13488888888,13599999999 GMT:E8.00

Latitude&Longitude Inquiry

|

WHERE#

|

LAT:N23.02930,LON:E114.32180,COURSE:0.00,S PEED:0.00KM/H,DATETIME:2015-05-23 14:39:11

Map URL Inquiry

|

URL#

| http://map.google.com/?q=22.557868,113.935090

<0.0km/h 0.0> <2014-12-12 07:32:13> IMEI:354188047752402

Address Inquiry

|

POSITION#

|

NOTE: Reply message’s language is determined by device’s language setting, if get position content failed, device will reply Google Map location link.

Status Inquiry

|

STATUS#

| BATTERY: XX% (Built-in Battery Power Percent)

INTERNET: CLOSED (No Network)

FAILED (Connecting Network or Failure)

SUCCESS (Connected to Network）

NET: NONE (No celluar Signal), HIGH / MED / LOW (Signal Strength) , 18(Signal value) GPS: CLOSED (GPS Module Closed); FIXED,N (Positioned and satellite number); UNFIX,0 (Not Positioned yet)

SPEED: 30KM/H

ACC: ON / OFF (ACC on or off)

RELAY: ON / OFF (Relay on or off)

POWER: CONNECTED / DISCONNECTED

(1P2o.5wVe(rVCeohnicnleecbtaetdteorryDvioslctoagnen)ected),

SENSOR: ON/OFF (S sor on or off), LEVEL: 3 (Sensitivity level 1-9) STATE: ARM (Arm or Disarm)

---|---|---

Alarms Parameters

|

ALARM#

| ID: 19172012644 (ID number of device)

STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value);alarm way

SHIFT: ON/OFF(alarm status); 300m(alarm value);alarm way

VIBRATE: ON/OFF(alarm status);3(sensitivity level);alarm way

ACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way ; ;

POWER DOWN: ON/OFF(alarm status);alarm way LOW VOLTAGE: ON/OFF(alarm status);alarm way NOTE: Alarm Ways: 0/1/2 ( 0 : SERVER only, 1: SMS+GPRS, 2 : GPRS+SMS+CALL )

Alarm Commands
Functions| Command Format| Explanation

Overspeed Alarm Setting

|

SPEED,A,B,M#

|

Example: SPEED,ON,100,1# (When the speed of the tracker exceeds 100km/h it will send alarm message via SMS and server)

A=ON/OFF, enable or cancel over speed alarm, default: OFF

B=1～255(km/h), speed limit, default：100(km/h); M=0/1/2, way of alarm, 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call default：1.

SPEED,OFF#

|

CANCEL OVERSPEED ALARM OK

Vibration Alarm Setting| SENALM,A,M#| Example: SENALM,ON,2# (Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered)

A=ON/OFF, default: OFF;

M=0/1/2, way of alarming, 0 : Serveronly, 1: SMS+Server, 2 : SMS+Server+Call, default:2

---|---|---
SENALM,OFF#| CANEL VIBRATE ALARM OK
Shift Alarm Setting| SHIFT,A,B,M#| Example: SHIFT,ON,300,1# ( Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle’s 300 meters’ shift will trigger the alarm, the alarm message will be sent via SMS and server )

A=ON/OFF; default:ON

B=Shift Distance (Range: 100-9999m)

M=0/1/2; way of alarm, 0 : Server only, 1: SMS+Server, 2: Server+SMS+CALL, default:1

SHIFT, OFF#| CANCEL SHIFT ALARM OK
Auto Arm By ACC| ACCARM, ON,M#| Example: ACCARM, ON,60# (Means when the engine turned to off status, the tracker will enter into arm status automatically after the 60s)

Arm Time: M=5-1800s, default: 60s

ACCARM, OFF#| Close auto arm function

ACC Status Change Alarm

|

ACCALM,A,B,M#

| Example: ACCALM, ON,2,2# (Means enable this alarm type, the tracker will send alarm message via SMS, server, and call when the engine start and flameout)

A=ON/OFF, Default: ON;

B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC

ON&OFF Alarm; Default:2

M: 0/1/2 (way of alarm): 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call, Default:1;

ACCALM, OFF#| Cancel the ACC alarm function
Power Disconnect Alarm| PWRALM,A,M| Example: PWRALM, ON,1# (Means when the external power disconnects the tracker will send an alarm message via SMS and server)

A=ON/OFF, default ON;

M=0/1/2, ways of alarming, 0: Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default:2；

PWRALM, OFF#| Close the power disconnect alarm

Low Voltage Alarm Setting

|

LVALM,A,B, M#

| Example: LVALM, ON,11.2V,1# (Means once the external power voltage is less than 11.5v the tracker will send an alarm message out via SMS and server)

A=ON/OFF, default： ON;

B=9-95 V, Low voltage threshold, can be a decimal, such as

12.5 V

M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call,default:1

LVALM, OFF#| CANCEL LOW VOLTAGE ALARM OK

Any Questions?

• E-mail: support@micodus.com.
• Skype: MiCODUS

Download the APP

Search “MiCODUS” in the iOS APP store Google Play Store, or just scan the QR code below to download MiCODUS APP:

Copyright ©2023 MiCODUS | All Rights Reserved

References

• Spionlink - SIM Card Service | Prepaid Data Plan | GPS Tracker Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>