HOOKE ROAD BXG.3049 Fender Flares Installation Guide
- June 15, 2024
- HOOKE ROAD
Table of Contents
BXG.3049 Fender Flares
Installation Guide
BXG.3049 Fender Flares
(1) Contents:
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 6 | Button Head Socket Cap Bolts Screws | M8*20 | |
| 12 | Button Head Socket Cap Bolts Screws | M6*20 | |
| 12 | Split Lock Washer | D6 | |
| 6 | Flat Washer | M8161 | |
| 12 | Flat Washer | M6161 | |
| 10 | Flange Hex Lock Nuts | M6 | |
| 6 | Flange Hex Lock Nuts | M8 | |
| 2 | Rivet Nut | M6 |
Rear
12| Button Head Socket Cap Bolts Screws| M635|
12| Split Lock Washer| D6|
12| Flat Washer| M616*1|
4| Flange Hex Lock Nuts| M6|
8| Rivet Nut| M6|
Tools required:
a. Drive Socket Ratchet Wrench;
b. 4mm & 5mm Hex Bit Socket;
c. Rivet Nut Tool;
d. 10mm & 13mm Wrench;
Installation time:
About 1.5 hours, 2-3 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.3049), please scan the QR code.
https://drive.google.com/drive/folders/14LHFGtEEHPNtSSlB-
VA8f7lmHlzPJ66H?usp=sharing
Installation instruction:
Driver Side Front Fender Flare Installation:
Step 1: Remove the factory front fender flare. Ready to install our
product.
Step 2: Install the rivet nut in the most right
hole with the rivet nut tool.
the rivet nut tool instruction: The 4mm Hex Bit Socket use in the top, 10mm
wrench stuck on the middle nut. Put the rivet nut in the hole, screw the
threaded end of the rivet nut tool into the rivet nut (Notice: Must be screwed
to the bottom), finally unscrew the rivet nut tool out.
Notes: The image on the upper
right only shows how the rivet nut tool is used.
Step 3: Next, Lift up the front fender flare and install the right three
holes. Use the Button Head Socket Cap Bolts Screws (M820), Flat Washer
(M8161), Flange Hex Lock Nuts (M8). Don’t tighten up those bolts.
Step 4: Next, Install the connecting brackets (A&B&C) in order
(Attention to distinguish the driver side and passenger side). Use the Button
Head Socket Cap Bolts Screws (M620), Flat Washer (M6161), Flange Hex Lock
Nuts (M6).
Tighten up this step and the step 3 bolts.
Driver Side
Passenger Side
Front Connecting Brackets (A)| Driver Side
Passenger Side
Front Connecting Brackets (B)| Driver Side
Passenger Side
Front Connecting Brackets (C)
---|---|---
Driver
Side Rear Fender Flare Installation：
Step 5: Remove the factory rear fender flare. Ready to install our
product.
Step 6: Install the rivet nut into the four
holes with the rivet nut tool.
Step 7: Install the rear fender flare. Use
the Button Head Socket Cap Bolts Screws (M635), Split Lock Washer (D6), Flat
Washer (M616*1). Only the upper installation holes need use the Flange Hex
Lock Nuts(M6). Tighten up those bolts.
Step 8: Repeat the same
installation steps in the passenger side.
Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life with
this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Google Hooke Road to find your parts
Feel Free To Share Your Vehicle @HookeRoad4x4
With The Hashtag #hookeroad If You’d Like
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>