SuperLightingLED DA-M WT 6 In 1 Tuya APP Cloud Control Wireless Remote Control User Manual
- June 15, 2024
- SuperLightingLED
Table of Contents
WiFi & RF to DALI Converter
Model No.: DA-M(WT)
6 in 1 Tuya APP cloud control / Wireless remote control / Powered 24VDC /
Encoding switch select address
User Manual Ver 1.0.0
Features
- WiFi & RF DALI master, 6 in 1 function, support single color, color temperature, RGB, RGBW, RGB+CCT, or switch light control.
- Tuya APP cloud control, support on/off, color temperature and brightness adjust, delay turn on/off light, timer run, scene edit and music play function.
- Match with RF 2.4G single zone or multiple zone remote control optional.
- 1 DALI address, support DT6 dimming, DT8-TC color temperature, DT8-RGB, DT8-RGBW or DT7 switch.
- In accordance with DALI standard protocol IEC 62386-101, 102, 207, 208, 209 and in compliance with DALI products from other international incorporation.
- Enable to select DALI address by encoding switch, support unicast, group and broadcast mode.
Technical Parameters
Input and Output
Power input| 24VDC
Static current| 2mA@24VDC
Input signal| Tuya APP + RF 2.4GHz
Output signal| DALI
Remote control distance| 30m(open and barrier-free)
Environment
Operation temperature| Ta: -20º C ~ +50º C
Case temperature (Max.)| Ta: +55 ºC
IP rating| IP20
Package
Size| W60 x L 60 x H40mm
Gross weight| 0.061kg
Warranty
Warranty| 5 years
Mechanical Structures and Installations
System wiring
Note:
- The above distance is measured in spacious(no obstacle) environment, Please refer to the actual test distance before installation.
- Please check if the WiFi router net in 2.4G band, the 5G band is not available, and do not hide your router network.
- Please keep the distance between DA-M(WT) devices and router close, and check the WiFi signals.
- WiFi signal strength detection: open the main interface of the device, click to enter the device interface, and click “Check the device network” to detect.
Wiring Diagram
Note: When DA-M(WT) is working, because the
power consumption of the WiFi module is too large, it cannot be powered by the
DALI bus power supply.
Light type settings
| SWITCH | C |
|---|---|
| DIM | W |
| CCT | Y |
| RGB | R |
| RGBW | G |
| RGB+CCT | B |
Please select the light type before Tuya APP network connection config.
Press and hold Match/Set key for 2s, switch 6 kinds light type in sequence,
and light type LED indicator turn corresponding color.
White: DIM
Yellow: CCT
Red: RGB
Green: RGBW
Blue: RGB+CCT
Cyan: SWITCH
Tuya APP network connection
Push twice Match/Set key fastly: Clear previous network connection, enter
Smart con RUN LED indicator flash fastly.
Press and hold Match/Set key for 5s: Clear previous network connection, enter
AP con RUN LED indicator flash slowly.
If smart config failed, please try AP config.
Repeat power on and off for 5 consecutive times, also clear previous network
connection, the RUN LED indicator flash fastly.
If Tuya APP network connection succeed, the RUN LED indicator stops flash.
And in Tuya APP, you can , RGB, RGBW, RGB+CCT, SWITCH device).
Tuya APP interface
White interface
For DIM type: Touch brightness slide to adjust brightness.
For RGB type: Touch brightness slide, get RGB mixed white firstly, then to
adjust white brightness.
For RGBW type: Touch brightness slide, adjust white channel brightness.
Color temperature
interface
For CCT type: Touch color wheel to adjust color temperature.
Touch brightness slide to adjust brightness.
For RGB+CCT type: Touch color wheel to adjust color temperature, RGB will turn
off automatically.
Touch brightness slide to adjust white brightness.
Colour interface
For RGB or RGBW type: Touch color wheel to adjust static RGB color.
Touch brightness slide to adjust color brightness.
Touch saturation slide to adjust color saturation, namely gradient from the
current color to white(RGB mixed).
For RGB+CCT type:
Touch color wheel to adjust static RGB color, CCT will turn off automatically.
Touch brightness slide to adjust color brightness.
Touch saturation slide to adjust color saturation, namely gradient from the
current color to white (RGB mixed)
Scene interface
The 1-4 scene is static color for all light type.
the inner color of these scene can be editable.
The 5-8 scene is dynamic mode for RGB type, such as green fade in and fade
out, RGB jump, 6 color jump, 6 color smooth.
Music, Timer,
Schedule
The music play can use smart phone music player or micro-phone as music signal
input.
The Timer key can turn on or turn off light in the next 24 hours.
The Schedule key can add multiple timers to turn on or turn off light
according to different time periods.
Match Remote Control (Optional)
Please select the same light type of RF remote control for matching,
End user can choose the suitable match/delete ways. Two options are offered
for selection:
Use the Match key
Match:
Short press match key, immediately press on/off
key (single zone remote) or zone key (multiple zone remote) on the remote.
The RUN LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 10s to delete all match, The RUN LED indicator
fast flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power of the receiver, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The RUN LED indicator blinks 3 times means match is successful.
Delete:
Switch off the power of the receiver, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The RUN LED indicator blinks 5 times means all matched remotes were deleted.
DALI address setting
Address value = X * 10 + Y.
For example: X = 5, Y = 4, Address value = 5 x 10 + 4 = 54.
Unicast mode
X is 0-6, Y is 0-9.
Address value 0-63 correspond to DALI unicast address 00-63.
For example:
Address value = 40, the unicast address value is 40.
Group mode
X is 7, Y is 0-F.
Address value 70-7F correspond to DALI group address 0-15.
For example:
Address value = 75, the group address value is 5.
Broadcast mode
X is 9, Y is 0-F.
Address value 90 – 9F correspond to broadcast address.