melodySusie Eos 5 LED UV Nail Lamp User Manual
- June 4, 2024
- melodysusie
Table of Contents
Eos 5 LED UV Nail Lamp
User Manual
Thank you for choosing MelodySusie! Please read this user guide carefully and keep it in an accessible location so you may refer to it later.
LG Chip
MelodySusie and LG have reached strategic cooperation. LG is our only nail lamp chips’ supplier. Each of our Eos 5 LED UV nail lamp beads has an LG Chip. LG Chip is high luminance and light efficiency, low electric power consumption, long lifespan. It is environment-friendly and no harm to skin and eyes. We combine to provide nail lamps with the most advanced technology for every customer.
Items Included
1 x MelodySusie Eos 5 LED/UV Nail Lamp (Including a rechargeable lithium battery) 1 x AC/DC Adaptor 1 x User Manual
How to Usti
Step 1: Connect the power cord and turn the switch on the back of the
machine to “o”, the 15s timer will light up.
or
Step 1: When using the battery, turn the switch on the back of the
machine to “-“, the 15s timer will light up
Step 2: Place your hands in the device and the lamp will automatically
turn on for 15 seconds. To stop drying, simply remove your hands.
Step 3: You can also choose a pre-set timer button (15s/the 30s/45s/60s)
as needed. The lamp will run until the preset time has elapsed.
Tips: If there is no action within 5 minutes, the indicator light will turn off. Touch any buttons on the operation panel to wake up.
Malfunctions and Solutions
Malfunctions
| Reasons|
Solutions
---|---|---
The nail lamp does not work well. / The beads do not turn on.| The power
cord’s AC plug is loose or poorly connected.| Reconnect the power cord and
make sure it is properly connected or contact MelodySusie’s customer service
team to change the power supply.
The nail lamp does not work well. The beads do not turn on.| The power cord’s
AC output is not properly connected to the lamp’s AC outlet.| Please make the
power
cord’s AC output is
properly connected to the lamp’s AC outlet.
The LCD screen and the countdown are normal. But the LED light beads don’t
turn on.| The LED light beads are defective or the lamp’s
internal circuits are damaged. Please contact our customer service team for
help.
The LED light beads are defective or the lamp’s internal circuits are damaged.
Please contact our customer service team for help.| The light bead is damaged.
Please contact
MelodySusie customer service team to change for the new light beads.
The power cord’s AC plug is not compatible with the outlet.| Please kindly
note the plug is a US plug. If you want to use the nail lamp in other
countries or areas, please use it with a universal adaptor.
II Please check whether there is water or dust on the button surface. Clean
the nail lamp with a dry cloth.
When pressing the button, the lamp doesn’t work.
The gel nail polish cannot be cured or dried| Insufficient curing time may
result in incomplete curing of your gel nail polish. The curing time
requirements vary from different gel polish brands and colors.| Please try to
extend the curing time appropriately until the nail surface is completely
cured. For best results, avoid moving your hand too much until curing is
complete.
The gel nail polish cannot be cured or dried
| The light on your nail surface is not enough.| Please adjust the angle of
your nail surface until it faces the light straight to ensure sufficient
illumination.
Please check whether the light beads have been aged.| Please contact the
customer service team to change the new light beads.
Use incompatible polish, such as regular nail polish, and nail lacquer.|
Please use LED, UV gel nail polish, or a compatible nail lamp.
The gel polish is a bit tacky after drying.| Please wipe your nail surface
with a gentle cleanser or alcohol prep pads.
There has a protective film on the touch screen, please take it off to get a smooth and bright panel.
How To Charge
Turn the back switch to “2, connect the power adapter, and insert it into the
power socket or power supply board. If the power indicator light flashes
repeatedly, the device is charging.
It takes about 4 hours. And the battery indicator light will turn on if fully
charged. Tips: Connect the adapter to charge when the battery drops below 20%.
The red indicator light will flicker. When the voltage is lower than 8.6V, the
timer buttons and red indicator light will flicker together.
This means a critically low battery and the lamp will not work soon. The
device can work for 90 minutes after being fully charged.
Note: Please don’t use it in the process of charging. If there is no
action within 3 minutes, the device will go into sleeping mode. Touch any
buttons on the operation panel to wake up.
Important Safety Information
-
Ensure your outlet supplies the correct power voltage to avoid damage to the device.
-
Do not unplug the lamp during operation.
-
Do not place heavy objects on the lamp housing.
-
Do not disassemble the device. Doing so could be dangerous and constitutes voiding warranty conditions.
-
If the power cord is damaged, it should be replaced by
MelodySusie or another authorized professional. -
Certain cosmetic substances may lead to adverse skin reactions.
-
Children under 18 years of age should not use this device without parental consent and supervision.
-
Please handle with care and do not drop
Eos 5 Specifications
Weight: 2.8 lbs
Input: AC100V~240V,50~60Hz
Size: 8.74 x 9.44 x 4.50 inches (LxWxH)
Wavelength: 365~400nm
Warranty and Customer Service
This lamp has a 6-month limited warranty on quality-related issues. Please register on our website to extend your warranty and to view this manual in other languages.
Service@melodysusie.com
service@melodysusie.com
http://www.melodysusie.com
Whipple Road, Union City, CA 94578
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>