Voltronic MT626 Contactless Card Readers Instruction Manual
- May 15, 2024
- Voltronic
Table of Contents
Voltronic MT626 Contactless Card Readers
Specifications
- Communication Interface: RS-232C three-wire serial port
- Power Supply: DC 5V
- J6 Interface Socket Specifications: 4Pins-2.54mm straight pin socket
- Transmission Speed: 115200bps
- Supported Card Types: RF card
- Operating Voltage: 5V
- Operating Current: 150mA
- Quiescent Current: 30mA
- LED Indicators: D1 (Status), D6 (Power)
Product Usage Instructions
Installation
Ensure the card reader module is installed with symmetrical mounting holes
and proper dimensions as specified.
Wiring and Connection
- Connect the power supply and communication lines to the designated pins of the J6 interface.
- Connect the card reader to the host/PC via the serial port.
- Power on the card reader.
Software Setup
Run the host/PC software that is compatible with the product for usage.
FCC Compliance
Ensure compliance with FCC regulations regarding operation and
interference. Maintain a minimum distance of 20cm between the device and the
body.
Instructions
Product Overview
MT626V202 is a contactless MIFARE®ONE (MF1) reader module, it is based on
13.56MHZ communication frequency. It can be widely used in terminal
peripherals in electric power, telecommunications, transportation,
petrochemical and other industrial occasions.
Interface definition
This product adopts RS-232C three-wire serial port and shares a J6 interface
with the power supply.
- Communication configuration: RS232C Signal levels Transmission speed 115200bps
- Power supply: DC 5V. J6 interface socket specifications: 4Pins-2.54mm straight pin socket with a pitch as shown below
Note : The input (I) output (0) shown in the table above is relative to this product.
Performance indicators
Installation size
The installation dimensions of the card reader module are as follows:
The unit is mm, R is the radius, and the mounting hole is symmetrical with the center point of the plate.
The card reader module is started for use
-
Define the wiring according to the interface of this product, and connect the power supply and communication lines as shown below
-
Connect the host/PC with the serial port of the card reader and power on ;
( Note : Please confirm the correct serial port number is selected, that is connected with your card read module) -
Run the host/PC software matching this product to use.
FCC regulatory compliance statement
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this the device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Information to user
Warning : changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
List of applicable FCC rules:
- 47 CFR Part 15, Subpart C 15.203
- 47 CFR Part 15, Subpart C 15.205
- 47 CFR Part 15, Subpart C 15.207
- 47 CFR Part 15, Subpart C 15.209
- 47 CFR Part 15, Subpart C 15.225
- 47 CFR Part 2.1093
Summarize the specific operational use conditions
This module can be used in IOT devices, the input voltage to the module is
nominally 5V.
Limited module procedures
This module is a limited module.
Trace antenna designs
The antenna is a PCB onboard antenna.
RF exposure considerations
This Module complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Antennas
If you desire to increase antenna gain and either change antenna type or use
same antenna type certified, a Class Il permissive change application is
required to be filed by us, or you (host manufacturer) can take responsibility
through the change in FCC ID (new application) procedure followed by a Class
Il permissive change application.
Label and compliance information
Please notice that if the FCC identification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the
enclosed module.
Information on test modes and additional testing requirements
- Test software: MT626V-CE
- Frequencies: 13.56MHZ
- Modulation Type: ASK
FCC other Parts, Part 15B Compliance Requirements for Host Product
Manufacturer
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
ISED compliance statement
This device contains license-exempt transmitters)/receivers) that comply with
Innovation, Science and
Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The license-exempt transmitter/receiver contained in this apparatus complies with Innovation, science and Economic Development Canada’s RSS applicable to license-exempt radio apparatus. The operation is authorized under the following two conditions:
- The apparatus shall not cause interference;
- The apparatus shall accept any electrical radio interference suffered, even if the interference is likely to compromise its operation.
ISED Radiation Exposure Statement
- Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 30852-MT626V202” any similar wording that expresses the same meaning may be used. The registration label for an Innovation, Science and Economic Development Canada module must be placed on the host product in a conspicuous place at all times.
- If there is no label, the host product must be labeled with the Innovation, Science and Economic Development Canada module registration number, preceded by the word “contains”, or similar wording along the same lines, which reads as follows:
Contains IC : 30852-MT626V202 is the approval number of the module.
FAQ
-
Q: What is the operating voltage of the card reader module?
A: The operating voltage is 5V with an operating current of 150mA and a quiescent current of 30mA. -
Q: How far is the read and write distance for RF cards?
A: The approximate read and write distance for RF cards is 4cm, influenced by the usage environment, card type, and power supply.